πŸ“š Exam by Category
β–Ύ
Objective Questions

Latest WBMSC Assistant Engineer Civil Exam Question (Objective Questions), MCQ in English

Subjects : Civil

Question Bank WBMSC Assistant Engineer (Civil) Exam - English
Back to Exam

Civil

Question 1Single Answer
What will be the depth of penetration of the plunger in Vicat Apparatus (IS : 5513 - 1976) from the bottom of the Vicat Mould, when the cement paste is tested for standard consistency, according to IS 4031 – 1988 ?
  1. A
    11 to 15 mm
  2. B
    8 to 10 mm
  3. C
    15 to 17 mm
  4. D
    5 to 7 mm
Question 2Single Answer
Two sewer pipelines A and B (having the same diameter and made of the same material) are laid at a bed slope of 1 in 225 and 1 in 625, respectively. Determine the ratio of their carrying capacities (QA to QB) .
  1. A
  2. B
  3. C
    1
  4. D
Question 3Single Answer
Select the correct statement with respect to an over - reinforced cement concrete section under the working stress method .
  1. A
    The compressive stress in steel reaches the allowable limit before the maximum tensile stress in concrete reaches the allowable limit
  2. B
    Tensile steel stress and maximum compressive stress in concrete simultaneously reach their allowable limits
  3. C
    The allowable limiting stress is reached in concrete before the steel stress reaches the limiting value
  4. D
    The tensile stress in steel reaches the allowable limit before the maximum compressive stress in concrete reaches the allowable limit
Question 4Single Answer
A cantilever beam of span L is built - in at the support. It is restrained against lateral deflection and torsion at the free end. The effective length of compression flange for the beam as per IS 800 : 2007 is
  1. A
    0.5 L
  2. B
    0.85 L
  3. C
    2 L
  4. D
    0.75 L
Question 5Single Answer
What is the principle of plane surveying ?
  1. A
    Working from part to whole
  2. B
    Working from point to area
  3. C
    Working from angle to volume
  4. D
    Working from whole to part
Question 6Single Answer
According is IS 5968 : 1987, the minimum radius of radius of curve to be provided in the alignment of unlined canals carrying a discharge of less than 30 cumecs up to 15 cumecs is :
  1. A
    100 m
  2. B
    1000 m
  3. C
    600 m
  4. D
    150 m
Question 7Single Answer
A Pelton wheel is to be designed for a pitch diameter of 1 m and jet diameter of 0.1 m. The number of buckets on the runner computed by Taygun’s formula is :
  1. A
    20
  2. B
    25
  3. C
    15
  4. D
    10
Question 8Single Answer
What is the effect of fly ash in concrete ?
  1. A
    Reduces the secondary hydration process
  2. B
    Increases the heat of hydration
  3. C
    Increases the amount of air entrainment
  4. D
    Reduces the heat of hydration
Question 9Single Answer
As per IS 456 : 2000, the minimum grade of concrete to be used for plain concrete and reinforced concrete, respectively, in concrete works exposed directly along the sea coast are :
  1. A
    M 20 and M 30
  2. B
    M 20 and M 25
  3. C
    M 22 and M 40
  4. D
    M 15 and M 25
Question 10Single Answer
Identify the property that changes as a function of the geometrical dimensions of a section in structural materials :
  1. A
    Mass density
  2. B
    Moment of inertia
  3. C
    Poission’s ratio
  4. D
    Modulus of elasticity
Question 11Single Answer
As per IRC (Indian Roads Congress) recommendation, what will be the designed stopping sight distance (in metres) at the vehicle speed of 80 km/h on a rural highway ?
  1. A
    120
  2. B
    140
  3. C
    70
  4. D
    60
Question 12Single Answer
No deduction is made in the quantity estimation for plastering work in cement mortar for openings having size up to :
  1. A
    0.5 m2
  2. B
    1.0 m2
  3. C
    3 m2
  4. D
    0.75 m2
Question 13Single Answer
What is the height of slump cone mould used for testing the workability of the concrete ?
  1. A
    20 cm
  2. B
    10 cm
  3. C
    30 cm
  4. D
    25 cm
Question 14Single Answer
Select the correct option with regard in the following statements (S1, S2) pertaining to pavements .
S1 : Present serviceability index is used for the functional evaluation of pavement surface condition
S2 : Rigid pavements are less affected by temperature variations than flexible pavements
  1. A
    Statements S1 is true and Statement S2 is false
  2. B
    Both statements S1 and S2 are false
  3. C
    Statements S1 is false and Statement S2 is true
  4. D
    Both statements S1 and S2 are true
Question 15Single Answer
If the quadrantal bearing of a line AB is S 31'35' E, then its whole circle bearing is equal in :
  1. A
    121o25'
  2. B
    148o25'
  3. C
    58o25'
  4. D
    211o25'
Question 16Single Answer
The overflowing sheet of water on a weir is called :
  1. A
    creek
  2. B
    crest
  3. C
    limp
  4. D
    nappe
Question 17Single Answer
According to IS 456 - 2000, what is the slump of a medium degree of workability of concrete if planed in heavily reinforced sections like slabs, beams, walls, columns ?
  1. A
    10 - 25 mm
  2. B
    25 - 50 mm
  3. C
    0 - 10 mm
  4. D
    50 - 100 mm
Question 18Single Answer
Which of the following is Kharif season in India ?
  1. A
    March / April to June / July
  2. B
    December / January to April / May
  3. C
    May / June to October / November
  4. D
    October / November to April / May
Question 19Single Answer
The estimated value of a built - up property at the end of its useful life without dismantled is called :
  1. A
    market value
  2. B
    book value
  3. C
    scrap value
  4. D
    salvage value
Question 20Single Answer
The amount of cement required for 100 m2 area, of damp proof course with 2.5 cm thinkness, in with proportion of 1: 2 : 4 (cement : sand : aggregate) will be :
  1. A
    2.5 m2
  2. B
    0.55 m2
  3. C
    1.10 m2
  4. D
    0.25 m2
Question 21Single Answer
What is the primary focus of kinematics in dynamics?
  1. A
    Forces causing motion
  2. B
    Motion without forces
  3. C
    Energy conservation
  4. D
    Momentum transfer
Question 22Single Answer
What is the primary purpose of evaluating bearing capacity in foundation design?
  1. A
    Ensure soil can support loads without failure
  2. B
    Minimize construction cost
  3. C
    Increase settlement
  4. D
    Enhance aesthetic appeal
Question 23Single Answer
Which bearing capacity theory is commonly used for shallow foundations?
  1. A
    Terzaghi’s theory
  2. B
    Rankine’s theory
  3. C
    Coulomb’s theory
  4. D
    Taylor’s theory
Question 24Single Answer
What field test is commonly used to estimate bearing capacity?
  1. A
    Standard Penetration Test (SPT)
  2. B
    Proctor test
  3. C
    Consolidation test
  4. D
    Triaxial test
Question 25Single Answer
What is the factor of safety for allowable bearing capacity?
  1. A
    2.5 to 3
  2. B
    1.5 to 2
  3. C
    4 to 5
  4. D
    1 to 1.5
Question 26Single Answer
What is immediate settlement in foundation design?
  1. A
    Elastic settlement occurring instantly
  2. B
    Settlement due to consolidation
  3. C
    Settlement due to shear failure
  4. D
    Settlement due to compaction
Question 27Single Answer
What is the allowable settlement for isolated footings on clay?
  1. A
    75 mm
  2. B
    50 mm
  3. C
    25 mm
  4. D
    100 mm
Question 28Single Answer
What is the allowable settlement for isolated footings on sand?
  1. A
    50 mm
  2. B
    75 mm
  3. C
    25 mm
  4. D
    100 mm
Question 29Single Answer
What is the primary purpose of proportioning shallow foundations?
  1. A
    Ensure uniform load distribution and stability
  2. B
    Minimize material usage
  3. C
    Increase settlement
  4. D
    Enhance aesthetic appeal
Question 30Single Answer
What is an isolated footing used for?
  1. A
    Support single column loads
  2. B
    Support multiple columns
  3. C
    Distribute load over large area
  4. D
    Support bridge piers
Question 31Single Answer
What is a combined footing used for?
  1. A
    Support two or more closely spaced columns
  2. B
    Support single column
  3. C
    Distribute load over weak soil
  4. D
    Support machine loads
Question 32Single Answer
What is a raft foundation used for?
  1. A
    Distribute load over large area in weak soils
  2. B
    Support single column
  3. C
    Minimize construction cost
  4. D
    Support deep foundations
Question 33Single Answer
What is a common type of pile foundation?
  1. A
    Driven precast pile
  2. B
    Spread footing
  3. C
    Strip footing
  4. D
    Mat foundation
Question 34Single Answer
What is the primary function of a pile foundation?
  1. A
    Transfer load to deeper, stronger soil
  2. B
    Distribute load over surface soil
  3. C
    Reduce settlement in firm soil
  4. D
    Increase soil permeability
Question 35Single Answer
What is the static formula for pile capacity based on?
  1. A
    Skin friction and end bearing
  2. B
    Soil permeability
  3. C
    Consolidation settlement
  4. D
    Shear strength only
Question 36Single Answer
What is a common dynamic formula for pile capacity?
  1. A
    Engineering News formula
  2. B
    Terzaghi’s formula
  3. C
    Meyerhof’s formula
  4. D
    Skempton’s formula
Question 37Single Answer
What is the formula for pile capacity using the Engineering News formula?
  1. A
    Q_u = (W h) / (s + C)
  2. B
    Q_u = (W h) / s
  3. C
    Q_u = (W h) / C
  4. D
    Q_u = (W h) / (s - C)
Question 38Single Answer
What is the primary consideration in pile group design?
  1. A
    Group efficiency and settlement
  2. B
    Individual pile capacity only
  3. C
    Soil permeability
  4. D
    Construction cost
Question 39Single Answer
What is the efficiency of a pile group?
  1. A
    Ratio of group capacity to sum of individual capacities
  2. B
    Ratio of individual capacity to group capacity
  3. C
    Ratio of settlement to load
  4. D
    Ratio of skin friction to end bearing
Question 40Single Answer
What is the purpose of a pile load test?
  1. A
    Verify pile capacity and settlement
  2. B
    Measure soil permeability
  3. C
    Calculate consolidation
  4. D
    Assess slope stability
Question 41Single Answer
What is the primary property of a fluid?
  1. A
    Inability to resist shear stress
  2. B
    High compressive strength
  3. C
    Fixed shape
  4. D
    High rigidity
Question 42Single Answer
What is the specific gravity of a fluid?
  1. A
    Ratio of fluid density to water density
  2. B
    Ratio of fluid viscosity to water viscosity
  3. C
    Ratio of fluid pressure to water pressure
  4. D
    Ratio of fluid volume to water volume
Question 43Single Answer
What is the total pressure force on a vertical plane surface submerged in a fluid?
  1. A
    F = p g h_c A
  2. B
    F = p g A
  3. C
    F = p h_c A
  4. D
    F = p g h_c / A
Question 44Single Answer
Where is the center of pressure located for a vertical plane surface?
  1. A
    Below the centroid
  2. B
    At the centroid
  3. C
    Above the centroid
  4. D
    At the surface
Question 45Single Answer
What is the force on a curved surface submerged in a fluid?
  1. A
    Sum of horizontal and vertical components
  2. B
    Horizontal component only
  3. C
    Vertical component only
  4. D
    No force
Question 46Single Answer
What is fluid kinematics concerned with?
  1. A
    Motion of fluid without considering forces
  2. B
    Forces causing fluid motion
  3. C
    Fluid properties at rest
  4. D
    Energy transfer in fluids
Question 47Single Answer
What is a streamline in fluid flow?
  1. A
    Path traced by a fluid particle tangent to velocity
  2. B
    Path perpendicular to velocity
  3. C
    Path of constant pressure
  4. D
    Path of constant density
Question 48Single Answer
What is the condition for irrotational flow?
  1. A
    Zero vorticity
  2. B
    Constant velocity
  3. C
    Zero velocity
  4. D
    Constant pressure
Question 49Single Answer
What is the velocity potential in fluid flow?
  1. A
    Scalar function whose gradient gives velocity
  2. B
    Vector function of pressure
  3. C
    Scalar function of density
  4. D
    Vector function of vorticity
Question 50Single Answer
What is the stream function used for?
  1. A
    Represent two-dimensional incompressible flow
  2. B
    Calculate pressure distribution
  3. C
    Measure vorticity
  4. D
    Determine fluid density
Important Questions Package

WBMSC Assistant Engineer Civil Exam Online Question Bank Package

Buy WBMSC Assistant Engineer Civil Important Questions, MCQ, question answer in Hindi & English. It will help you to score high marks in WBMSC Assistant Engineer Civil question bank 2026 in Online, PDF & Print study material.

+ Free Monthly Current Affairs, GK & more PDF Download
Sr.Package NameAmount
1.WBMSC Assistant Engineer (Civil) Exam - English
Description : 1000 Question With Answer
β‚Ή101 [β‚Ή500]
2.WBMSC Assistant Engineer (Civil) Exam - English
Description : 2000 Question With Answer
β‚Ή151 [β‚Ή500]
3.WBMSC Assistant Engineer (Civil) Exam - English
Description : 3000 Question With Answer
β‚Ή181 [β‚Ή500]
4.WBMSC Assistant Engineer (Civil) Exam - English
Description : 1000 Question & Answer Download in PDF (Send by Email)
β‚Ή151 [β‚Ή550]
5.WBMSC Assistant Engineer (Civil) Exam Question Bank Book - English
Description : 1000 Question with Answer (Printed Material)
β‚Ή390 [β‚Ή650]
Back to Exam