A tank of length, breadth and height in the ratio of 2:1:2 is full of water. The ratio of hydrostatic force at the bottom to that at any larger vertical surface is
A
1
B
2
C
3
D
4
Question 3Single Answer
Which of the following fluids exhibit a certain shear stress at zero shear strain rate followed by a straight line relationship between shear stress and shear strain rate?
A
Newtonian fluid
B
Ideal Bingham plastic fluids
C
Pseudo-plastic fluids
D
Dilatent fluids
Question 4Single Answer
What is the specific gravity of a marble stone, which weighs 400N in air, and 200N in water? (g=10m/s2)
A
8
B
6
C
4
D
2
Question 5Single Answer
What is the intensity of pressure in the following SI units, when specific gravity of mercury is 13.6 and the intensity of pressure is 400KPa ?
A
0.3 bar or 4.077m of water or 0.29 mm of Hg
B
4 bar or 5.077m of water or 0.399 mm of Hg
C
0.3 bar or 5.077m of water or 0.599 mm of Hg
D
4 bar or 4.077m of water or 0.299 mm of Hg
Question 6Single Answer
Consider the following statements:
1.If a small upward displacement is given to a floating body, it results in the reduction of the buoyant force acting on the body
2.A slight horizontal displacement does not change either the magnitude or the location of the buoyant force
Which of the above statements is/are correct?
A
Both 1 and 2
B
1 only
C
2 only
D
Neither 1 nor 2
Question 7Single Answer
State whether following flow field is physically possible?
A
Possible for steady, incompressible flow
B
Possible for unsteady, incompressible flow
C
Possible for steady, compressible flow
D
Not Possible
Question 8Single Answer
In a differential manometer, a head of 0.5 m of fluid A in limb 1 is found to balance a head of 0.3 m of fluid B in limb 2. The atmospheric pressure is 760 mm of mercury. The ratio of specific gravities of A to B is
A
0.25
B
0.26
C
2
D
4
Question 9Single Answer
A Reversed Carnot Engine removes 50 kW from a heat sink. The temperature of the heat sink is 250 K and the temperature of the heat reservoir is 300 K. The power required of the engine is
A
10 kW
B
20 kW
C
30 kW
D
50 kW
Question 10Single Answer
On which of the following just in time manufacturing philosophy emphasizes ?
A
man power
B
profit
C
inventory
D
manufacturing
Question 11Single Answer
In a stream line steady flow, two points A and B on a stream line are 1m apart and the flow velocity varies uniformly from 2m/s to 5m/s. What is the acceleration of fluid at B?
A
3 m/s2
B
6 m/s2
C
9 m/s2
D
15 m/s2
Question 12Single Answer
The stream function is given by Ψ = 3xy, then the velocity at the point (2,3) is
A
9
B
-6
C
117
D
10.8
Question 13Single Answer
The boundary layer thickness at a given distance from the leading edge of a flat plate is
A
More for lighter fluid
B
More for denser fluid
C
Less for denser fluid
D
Less for lighter fluid
Question 14Single Answer
In a laminar flow through a circular pipe, the discharge varies
A
Linearly with fluid density
B
Inversely with pressure drop
C
Directly as square of pipe radius
D
Inversely with fluid velocity
Question 15Single Answer
A fluid is flowing over a flat plate. At distance of 8 cm from the leading edge, the Reynolds number is found to be 25600. The thickness of the boundary layer at this point is
A
1.5mm
B
2.5mm
C
4.0mm
D
5.0mm
Question 16Single Answer
Air is flowing over a flat plate with a free stream velocity of 24 m/s, and its kinematic viscosity is 72 ×10-6m2/s. If at a particular point, the Reynolds number is 30000, its location from the leading edge is
A
0.05m
B
0.07m
C
0.08m
D
0.09m
Question 17Single Answer
In a refrigerator, the evaporator and condenser coil temperatures are –33°C and 27°C, respectively. Assuming that the maximum COP is realized, the required power input for a refrigerating effect of 4 kW is
A
8 kW
B
4 kW
C
2 kW
D
1 kW
Question 18Single Answer
In a hydraulic coupling
A
The magnitudes of input and output torques are equal
B
The magnitudes of input torque is greater than output torque
C
The magnitudes of input torque is less than output torque
D
The magnitudes of input torque is negligible as compared to output torque
Question 19Single Answer
Consider the following statements:
1.The wheel can be operated freely in air
2.Pressure at the exit of the nozzle is atmospheric
3.Pressure does not vary along the moving vanes
4.Change the direction of momentum imparts thrust over moving vanes Which of the following statements are applied to impulse turbine?
A
1,2 and 3 only
B
1,2 and 4 only
C
3 and 4 only
D
1,2, 3 and 4
Question 20Single Answer
A water jet 0.0015m2in area issues from a nozzle with 15 m/s velocity. It is made to impinge perpendicular on to a plate that moves away from the jet with a velocity of 5 m/s. The force on the plate due to this impact is
A
150 N
B
1470 N
C
340 N
D
900 N
Question 21Single Answer
Consider the following statements with regard to hydraulic turbines:
1.Kaplan turbines are most efficient at part load operations.
2.If n is the number of jets in a Pelton turbine, then the specific speed is proportional to n2.
3.The flow ratio of Francis turbines are in the range of 0.1 – 0.3.
Which of the above statements is/are correct?
A
1,2 and 3
B
1 and 2 only
C
1 and 3 only
D
2 and 3 only
Question 22Single Answer
Which of the following is a Vector quantity ?
A
Energy
B
Mass
C
Momentum
D
Angle
Question 23Single Answer
Bernoulli’s equation is applicable between any two points located in
A
Rotational flow of an incompressible fluid
B
Irrotational flow of compressible or incompressible fluid
C
Steady, rotational flow of an incompressible fluid
D
Steady, irrotational flow of an incompressible fluid
Question 24Single Answer
Water flows through a smooth circular pipe of diameter D and length L because of a pressure difference ΔP across the length. The volume flow rate is Q and the flow is turbulent with Reynolds number 105. If the pressure difference is increased to 4ΔP the volume flow rate will be
A
2Q
B
A little more than 2Q
C
A little less than 2Q
D
4Q
Question 25Single Answer
Heat is lost from a 100 mm diameter steam pipe placed horizontally in ambient air at 30°C. If the Nusselt number is 25 and the thermal conductivity of the air is 0.03 W/m K, then the heat transfer coefficient will be
A
7.5 W/m2K
B
15 W/m2K
C
25 W/m2K
D
35 W/m2K
Question 26Single Answer
For laminar flow through a round pipe, the shear stress
A
Remains constant over the cross-section
B
Varies linearly with the radial distance
C
Must be zero at all point
D
Varies parabolically with radial distance
Question 27Single Answer
Percentage clongation during tensile test is indicative of
A
Creep
B
Malleability
C
Ductility
D
Elasticity in the metal
Question 28Single Answer
Which of the above statements is not correct in the context of laminar flow through a pipeline?
A
Shear stress is zero at the center and varies linearly with pipe radius
B
Head loss is proportional to square of the average flow velocity
C
The friction factor varies inversely with flow Reynolds number
D
No dispersion of die injected into the flow stream
Question 29Single Answer
Laminar flow between closely spaced parallel plates is governed by the consideration of which one of the following pair of forces?
A
Pressure and inertial forces
B
Gravity and inertial forces
C
Viscous and inertial forces
D
Pressure and inertial forces
Question 30Single Answer
Formation and collapse of vapour bubbles are believed to be the root cause for cavitation in hydraulic turbines. Most favorable condition for the formation of bubbles is set in the turbine at
A
Penstock/nozzl
B
Guide vanes/Inlet of the runner
C
Vanes receiving impact of jet
D
Outlet of the runner/Entrance of the draft tube
Question 31Single Answer
For fully developed laminar flow through a circular pipe with Reynolds number Rethe friction factor is
A
Inversely proportional to Re
B
Proportional to Re
C
Proportional to square of Re
D
Independent of Re
Question 32Single Answer
The ratio of power outlet of the pump to the power input to the pump is known as
A
Mechanical efficiency
B
Static efficiency
C
Overall efficiency
D
Manometric efficiency
Question 33Single Answer
A pump is defined as a device which converts
A
Hydraulic energy into Mechanical energy
B
Mechanical energy into Hydraulic energy
C
Kinetic energy into Mechanical energy
D
None of the above
Question 34Single Answer
The specific speed of a pump is defined as the speed of the unit of such a size that is
A
Delivers the unit discharge at unit head
B
Requires unit power to develop unit head
C
Delivers the unit discharge at unit power
D
Produces unit power with unit head available
Question 35Single Answer
Negative slip occurs in reciprocating pumps, when delivery pipe is
A
Long and suction pipe is short and pump is running atlow speed
B
Long and suction pipe is short and pump is running at high speed
C
Short and suction pipe is long and pump is running at low speed
D
Short and suction pipe is long and pump is running at high speed
Question 36Single Answer
The pressure inside a soap bubble of 50 mm diameter is 25 N/m2 above the atmospheric pressure. The surface tension in soap film would be
A
0.156 N/m
B
0.313 N/m
C
0.624 N/m
D
0.078 N/m
Question 37Single Answer
A Newtonian fluid is one which
A
Is viscous but incompressible
B
Has a linear relationship between the shear stress and the rate of angular deflection
C
Exhibits an increase in viscosity with increasing rate of deformation
D
Exhibits a decrease in viscosity with increasing rate of deformation
Question 38Single Answer
Unlike the viscosity of fluids, the viscosity of gases increases with increasing temperature. This is due to
A
Increased cohesive force between the molecule
B
Increased momentum transfer in the molecules
C
Decreased momentum transfer in the molecules
D
Increase in both cohesive force and momentum transfer
Question 39Single Answer
Manometer is a device used for measuring
A
Velocity at a point in a fluid
B
Pressure at a point in a fluid
C
Discharge of a fluid
D
None of the above
Question 40Single Answer
When a dolphin glides through air, it experiences an external pressure of 0.75 m of mercury. The absolute pressure on dolphin when it is 5m below the free surface of the water is
A
0.10 N/m2
B
0.5 N/m2
C
1.0 N/m2
D
0.15 N/m2
Question 41Single Answer
Which of the above statements is correct?
A
For a floating body, the stable equilibrium condition exists when position of metacenter remains higher than the center of gravity of the body
B
For a floating body, the stable equilibrium condition exists when position of metacenter remains lower than the center of gravity of the body
C
For a floating body, the neutral equilibrium condition exists when position of metacenter remains higher than the center of gravity of the body
D
For a floating body, the unstable equilibrium condition exists when position of metacenter remains higher than the center of gravity of the body
Question 42Single Answer
A wall of 0.6m thickness has normal area of 1.5 m2 and is made up of material of thermal conductivity 0.4 W/mK. If the temperature on the two sides of the wall are 800°C and 1000°C, the thermal resistance of the wall is
A
1.8 K/W
B
1.8 W/K
C
1 K/W
D
1 W/K
Question 43Single Answer
A flownet is a graphical representation of streamlines and euqipotnetial lines such as these lines
A
Intersect each other at various different angles forming irregular shaped nets
B
Intersect each other orthogonally forming curvilinearsquares
C
Indicate the direction but not magnitude of vector
D
Indicate the direction and magnitude of vector
Question 44Single Answer
Which of the above statements is correct for the velocity of potential?
A
Existence of velocity potential is an indication of irrotational nature of the flow
B
The velocity potential automatically satisfies the continuity equation
C
Velocity potential can be defined only for 2-dimensional flow
D
All of the above
Question 45Single Answer
Angle of diverging portion of the venturimeter is limited to 7°, because:
1.Flow decelerates in the diverging portion and pressure increases in the downstream direction. Hence, the fluid experience an adverse pressure gradient, if the divergence angle is large.
2 .Flow separation takes place due to adverse pressure gradient when divergence angle is large.
3 .If the divergence angle is large, a negative pressure is created at the throat which obstructs the flow of fluid.
Which of the above reasons are correct?
A
1, 2 and 3
B
1 and 2 only
C
1 and 3 only
D
2 and 3 only
Question 46Single Answer
A gas is flowing through an insulated nozzle. If the inlet velocity of gas is negligible and there is an enthalpy drop of 45kJ/kg, the velocity of gas leaving the nozzle is
A
100m/s
B
200m/s
C
300m/s
D
350m/s
Question 47Single Answer
Which of the above statements are correct for turbo-prop powered aircrafts?
1 .The propulsion efficiency of turbo-prop is higher than that of turbo-jet and rockets for low speeds up to about 800km/hr.
2.For the same thrust the turbine in the turbo prop aircraft is smaller than in the turbo-jet aircraft.
3.For the turbo-prop the flight velocity cannot exceed the jet velocity.
A
1,2 and 3
B
1 and 2 only
C
2 and 3 only
D
1 and 3 only
Question 48Single Answer
If absolute jet exit velocity from a jet engine is 2800m/s and forward flight velocity is 1400m/s then propulsive efficiency is
A
33.33%
B
40%
C
66.66%
D
90%
Question 49Single Answer
An air-breathing aircraft is flying at an altitude where the air density is half the value at ground level. With reference to the ground level, the air fuel ratio at this altitude will be
A
1
2
B
1
C
2
D
4
Question 50Single Answer
Which of the above statements are correct for rockets?
1.Unlike the turbo-jet aircraft, in rockets the flight velocity can exceed the jet velocity.
2.In rockets gases having lower molecular weight increase the specific thrust.
3.In rockets the gases are expanded in the nozzle up to the atmospheric pressure.
A
1,2 and 3
B
1 and 2 only
C
2 and 3 only
D
1 and 3 only
Important Questions Package
TNPSC MVI Exam Online Question Bank Package
Buy TNPSC MVI Important Questions, MCQ, question answer in Hindi & English. It will help you to score high marks in TNPSC MVI question bank 2026 in Online, PDF & Print study material.
+ Free Monthly Current Affairs, GK & more PDF Download
Sr.
Package Name
Amount
1.
TNPSC Motor Vehicle Inspector Exam Paper II - English
Description : 1000 Question With Answer
₹101[₹500]
2.
TNPSC Motor Vehicle Inspector Exam Paper II - English
Description : 2200 Question With Answer
₹151[₹500]
3.
TNPSC Motor Vehicle Inspector Exam Paper II - English
Description : 1000 Question & Answer Download in PDF (Send by Email)
₹151[₹550]
4.
TNPSC Motor Vehicle Inspector Exam Paper II Question Bank Book - English
Description : 1000 Question with Answer (Printed Material)
₹390[₹650]
5.
TNPSC Motor Vehicle Inspector Exam Paper 1 - English (old)
Description : 1000 Question & Answer Download in PDF (Send by Email)
₹151[₹450]
Automobile and Mechanical Engineering)
Question 51Single Answer
What is single deck and double deck ?
A
Bus
B
Scooter
C
Van
D
Moped
Question 52Single Answer
Vijay Super 150 CC is a ........ .
A
moped
B
van
C
truck
D
scooter
Question 53Single Answer
Main part of a chassis is ........ .
A
steering system
B
transmission system
C
brake system
D
All of these
Question 54Single Answer
Producer of three wheeler vehicle is ........ .
A
TVS
B
Atlas
C
Hero Majestic
D
Vikram
Question 55Single Answer
Which company produce Vespa XE scooter ?
A
Maharashtra Scooter
B
Scooter India
C
Lohiya Machine
D
Bajaj Auto
Question 56Single Answer
Delivery van is a ............ vehicle .
A
light
B
medium
C
Both (a) and (b)
D
heavy
Question 57Single Answer
Which of the following is an example of transmission system ?
A
Clutch
B
Gear box
C
Universal joint
D
All of these
Question 58Single Answer
Foreigner vehicle is
A
Toyota
B
Contesa
C
Opel Astra
D
None of these
Question 59Single Answer
Full form of LMV is
A
Light Moving Vehicle
B
Light Motor Vehicle
C
Load Moving Vehicle
D
Light Motion Vehicle
Question 60Single Answer
Main part of motor vehicle is
A
chassis
B
body
C
Both (a) and (b)
D
None of these
Question 61Single Answer
Kinetic India Limited (Pune) produce
A
Luna
B
Laxmi
C
Swega
D
Hero Majestic
Question 62Single Answer
Which company made hard moped ?
A
Tamil Nadu Moped
B
Moped India
C
Sain and Pandit
D
Hero Majestic
Question 63Single Answer
......... in an automobile is the source of power .
A
Engine
B
Output
C
Steering system
D
Suspension system
Question 64Single Answer
Chassis of the automobile supports, its
A
body
B
engine
C
transmission
D
All of these
Question 65Single Answer
............ is the birth place of the automobile .
A
Germany
B
Japan
C
America
D
Italy
Question 66Single Answer
First motor car race was held in ............ .
A
1896
B
1898
C
1895
D
1899
Question 67Single Answer
Generally motor vehicle is
A
backward drive
B
right hand drive
C
centre drive
D
left hand drive
Question 68Single Answer
Heavy vehicle is
A
Red Ford
B
Contesa
C
Maruti 1000
D
Yezdi
Question 69Single Answer
The first automobile powered by steam engine was built in France by
A
Nicholas-Joseph Cugnot
B
Daimler Benz
C
Henry Ford
D
Elwood J. Haynes
Question 70Single Answer
In the year 1885, the real automobile was built by which of the following man ?
A
Nicholas-Joseph Cugnot
B
Daimler Benz
C
Henry Ford
D
Elwood J. Haynes
Question 71Single Answer
Vehicle without body is known as
A
wheel
B
ring
C
axle
D
chassis
Question 72Single Answer
Which of the following is called power plant ?
A
Axle
B
Chassis
C
Wheel
D
Engine
Question 73Single Answer
The first motor car appeared in India in
A
1870
B
1898
C
1753
D
1947
Question 74Single Answer
The first successful American car was built by
A
Duryea Brothers
B
Lanchester
C
Both (a) and (b)
D
None of these
Question 75Single Answer
Which is the India manufacturer of jeeps ?
A
Ashok Leyland
B
Hindustan Motors
C
Mahindra and Mahindra
D
None of the above
Question 76Single Answer
Which of the following is the Indian manufacturer of moped ?
A
Enfield India
B
Indian Automotives
C
Moped India
D
All of these
Question 77Single Answer
Indian manufacturer of tractors are
A
Eicher
B
Escorts
C
Gujarat Tractors
D
All of these
Question 78Single Answer
Which of the following Udyog ?
A
Maruti 800 car
B
Maruti 800 deluxe car
C
Maruti 800 flat roof car
D
All of these
Question 79Single Answer
In 1935, ...... made an automobile industry in are the kinds of India .
A
Sir M. Visvesvaraya
B
Sir Rajdoot
C
Sir Charles and Frank
D
None of the above
Question 80Single Answer
Which of the following are the Indian manufacturer of scooters ?
A
Andhra Pradesh Scooters
B
API
C
Bajaj Auto
D
All of the above
Question 81Single Answer
In petrol engine, combustion pressure is
A
1 : 4-1 : 10
B
1 : 12-1 : 22
C
3 : 5-5 : 10
D
5 : 12-5 : 22
Question 82Single Answer
Which of the following is a type of super charger ?
A
Piston type
B
Blower type
C
Turbo type
D
All of these
Question 83Single Answer
What is called internal diameter of cylinder ?
A
Throw
B
Bore
C
TDC
D
BDC
Question 84Single Answer
Engine is a device, which converts
A
mechanical energy into heat energy
B
heat energy into mechanical energy
C
mechanical energy into sound energy
D
None of the above
Question 85Single Answer
Engine valve open by
A
Crank shaft
B
Cam shaft
C
Roker shaft
D
Valve guide
Question 86Single Answer
Which metal cylinder is made ?
A
Brass
B
Cast iron
C
Aluminium
D
None of these
Question 87Single Answer
In compression stroke piston move
A
upward
B
BDC to TDC
C
downward
D
left to right
Question 88Single Answer
Two-stroke engine is ......... engine .
A
water cooled
B
air cooled
C
oil cooled
D
None of these
Question 89Single Answer
If the clearance volume 6 cu/inch and the displacement volume is 36 cu/inch. What will be value of compression ratio ?
A
3 : 1
B
4 : 1
C
5 : 1
D
7 : 1
Question 90Single Answer
The power produced in cylinder is called ......... .
A
brake horse power
B
indicated horse power
C
frictional horse power
D
None of these
Question 91Single Answer
Another name of diesel engine is
A
High volume combustion engine
B
Low volume combustion engine
C
Constant volume combustion engine
D
No volume combustion engine
Question 92Single Answer
The volume remain at the top of the piston, when the piston is at TDC is called at ......... .
A
unswept volume
B
clearance volume
C
Both (a) and (b)
D
swept volume
Question 93Single Answer
A fuel which has a higher itself ignition temperature
A
detonates less
B
helps detonation
C
results in smooth burning of charge
D
increase the rate of ignition
Question 94Single Answer
Pre-ignition
A
is the spontaneous ignition of the last part of charge
B
is resorted to at higher altitudes
C
increases the efficiency and saves unburnt fuel
D
causes reduced efficiency and loss of power engine
Question 95Single Answer
The efficiency of internal combustion ranges from
A
15%-35%
B
20%-40%
C
25%-30%
D
30%-35%
Question 96Single Answer
The firing order in a four-stroke IC engine is
A
1-2-3-4
B
1-4-3-2
C
1-3-4-2
D
1-2-4-3
Question 97Single Answer
The quantity control method of governing is used in
A
diesel engines
B
rocket engines
C
petrol engines
D
steam engines
Question 98Single Answer
The delay period in SI engine is about
A
0.10 s
B
0.0002 s
C
0.002 s
D
the ignition time lag
Question 99Single Answer
Which among the following can be used for Turbojet engines ?
A
Kerosene
B
Methyl alcohol
C
High speed diesel
D
Demethylated spirit
Question 100Single Answer
The thermal efficiency of an IC engine is
A
more than external combustion engine
B
less than external combustion engine
C
equal to external combustion engine
D
independent of method of fuel ignition
Question 101Single Answer
If a four-strokes engine is revolving of at 1200 rpm, then the number of explosions are equal to
A
1200
B
600
C
2400
D
300
Question 102Single Answer
If L is the stroke length and r is the crank radius, then
A
L = r
B
L = 4r
C
L =
D
L = 2r
Question 103Single Answer
In IC engine the type of governing used is
A
quality governing
B
quantity governing
C
hit and miss governing
D
None of these
Question 104Single Answer
Which one is not related of IC engine ?
A
Gas turbine
B
Four-stroke IC engine
C
Two-stroke Sl engine
D
Steam turbine
Question 105Single Answer
Which is related to IC engine only ?
A
Distributor
B
Spark plug
C
Atomizer
D
Carburettor
Question 106Single Answer
Spark ignition engine works on
A
Carnot cycle
B
Rankine cycle
C
constant pressure cycle
D
constant volume cycle
Question 107Single Answer
The term 'Bore' in IC engine is used for
A
diameter of the piston
B
inside diameter of cylinder
C
diameter of piston ring
D
None of the above
Question 108Single Answer
Displacement volume or swept volume is the volume displaced by the piston in
A
two-strokes
B
four-strokes
C
one-stroke
D
half-stroke
Question 109Single Answer
The piston, if an IC engine completes two strokes in
A
180° of crank rotation
B
360° of crank rotation
C
540° of crank rotation
D
720° of crank rotation
Question 110Single Answer
The pistons are usually given a coating such as tin plating in order to
A
conduct heat efficiency
B
reduce possibility of scoring
C
reduce friction
D
None of the above
Question 111Single Answer
Piston rings are usually made of
A
steel
B
cast iron
C
aluminium
D
babbit
Question 112Single Answer
In loop scavenging, the top of piston is
A
contoured
B
depressed
C
slanted
D
flat
Question 113Single Answer
In the crank case method of scaversing the air pressure is produced by
A
movement of piston
B
centrifugal pump
C
national aspirator
D
None of these
Question 114Single Answer
Connecting rod is made of
A
aluminium alloy
B
cast iron
C
copper alloy
D
medium carbon steel
Question 115Single Answer
In a four-stroke four cylinder diesel engine, number of carburettors used is
A
0
B
1
C
2
D
4
Question 116Single Answer
The material of the exhaust valve is
A
aluminium alloy
B
cast iron
C
silicon chrome steel
D
low carbon steel
Question 117Single Answer
The flywheel is located on the
A
racker arm shaft
B
crankshaft
C
cam shaft
D
All of these
Question 118Single Answer
The function of the governor is to
A
supply energy during non-working strokes
B
supply energy when the piston is at dead centre
C
run the engine at some average constant speed
D
control vibrations due to the reciprocating parts
Question 119Single Answer
The popular firing order of a four-stroke SI engine is
A
1-3-4-2
B
1-2-3-4
C
4-3-2-1
D
2-4-3-1
Question 120Single Answer
Morse test is used to determine efficiency of
A
multi-cylinder engines
B
four-stroke engines
C
two-stroke engines
D
None of these
Question 121Single Answer
In petrol engine, actual pressure developed compared to the predicted maximum pressure is
A
50%
B
25%
C
70%
D
90%
Question 122Single Answer
In a naturally aspirated diesel engine, air is supplied by
A
a super charger
B
a centrifugal blower
C
a vacuum chamber
D
an injection tube
Question 123Single Answer
Which of the following symptoms show that the combustion is necessarily complete ?
A
Presence of free carbon in exhaust
B
Presence of carbon mono-oxide in exhaust
C
Presence of oxygen in exhaust
D
Presence of nitrogen in exhaust
Question 124Single Answer
Those engines where fuel is burnt outside the combustion chamber are called
A
External combustion engine
B
Internal combustion engine
C
Both (a) and (b)
D
None of the above
Question 125Single Answer
Which of the following is not the example of internal combustion engine ?
A
Wankle engine
B
Petrol engine
C
Steam engine
D
Diesel engine
Question 126Single Answer
Which of the following is correct ?
A
I H P =
B
I H P =
C
I H P =
D
I H P =
Question 127Single Answer
In four stroke engine the number of revolutions is
A
N =
B
N =
C
N = RPM
D
N =
Question 128Single Answer
The amount of power which is available at flywheel for useful work is known as
A
I H P
B
H P
C
Brake horse power
D
None of the above
Question 129Single Answer
Diesel engine is ...... than petrol engine .
A
heavier
B
lesser
C
greater
D
None of these
Question 130Single Answer
What is the percentage of silicon in a cast iron cylinder ?
A
9.5
B
2.1
C
2.9
D
1.2
Question 131Single Answer
Diesel engine uses ...... oil for its running .
A
diesel
B
petrol
C
kerosene oil
D
None of these
Question 132Single Answer
Most of the engines used in present day automobiles have ...... of cylinders .
A
In-line
B
V-type
C
opposed type
D
radial type
Question 133Single Answer
Due to less number of parts 2-stroke engines are in …....... weight .
A
heavier
B
lighter
C
same
D
constant
Question 134Single Answer
Which of the following is the function of piston ?
A
In exhaust stroke it pushed out exhaust gases
B
It works as a guide for the upper part of connecting rod
C
Both (a) and (b)
D
None of the above
Question 135Single Answer
Which is the lowest part of the piston ?
A
Ring
B
Skirt
C
Pin
D
Dam
Question 136Single Answer
The space left in the circumference of piston after cutting ring groove is called
A
slot skirts
B
ring groove
C
running part
D
ring land
Question 137Single Answer
The place where gudgeon pin is fixed in the piston is called
A
pin boss
B
ring carrier
C
ring land
D
slot skirts
Question 138Single Answer
Piston ring must withstand temperature upto …….. °C without losing their tension .
A
100
B
3000
C
1000
D
300
Question 139Single Answer
Oil sump is the ......... most part of engine .
A
highest
B
lowest
C
higher
D
lower
Question 140Single Answer
Main parts of crank shaft are
A
journals
B
throws
C
webs
D
All of these
Question 141Single Answer
In case of a four stroke diesel engine, the heat carried away by the exhaust gases will be around
A
5-7%
B
7-10%
C
10-20%
D
20-35%
Question 142Single Answer
In a two stroke engine, the working cycle is complete in the number of revolution of the crank shaft equal to
A
one
B
two
C
three
D
four
Question 143Single Answer
Which one is a spark ignition engine ?
A
Petrol engine
B
Diesel engine
C
Steam engine
D
None of these
Question 144Single Answer
Which of the following defines IC engine most appropriately ?
A
Product of combustion is used as working substance
B
Combustion of fuel takes place inside the cylinder
C
Petrol or diesel is used as fuel
D
Works on diesel or otto cycle
Question 145Single Answer
In diesel engine, the suction contains
A
air
B
fuel
C
mixture of air and fuel
D
air or fuel
Question 146Single Answer
Spark ignition engine is
A
petrol engine
B
diesel engine
C
steam engine
D
Cl engine
Question 147Single Answer
For a four-cylinder engine, the firing order for evenness of torque is
A
1-2-3-4
B
1-3-2-4
C
1-4-3-2
D
1-3-4-2
Question 148Single Answer
The silencer of an IC engine
A
reduces noise
B
decreases brake specific fuel consumption
C
increases brake specific fuel consumption
D
has no effect on efficiency
Question 149Single Answer
The compression ratio for a practical diesel engine usually lies in the range
A
5-7
B
7-9
C
10-15
D
16-22
Question 150Single Answer
Vocational petrol is a mixture of
A
petrol or oil
B
staterun gasoline or diesel
C
staterun gasoline or cranked gasoline
D
None of the above
Question 151Single Answer
If a submerged body displaced from its equilibrium position, returns to its original position, it is called __________.
A
thermal equilibrium
B
neutral equilibrium
C
unstable equilibrium
D
stable equilibrium
Question 152Single Answer
In a flow measurement, a venturi meter is preferred over an orifice plate because _____.
A
energy of head loss is less
B
It is cheaper
C
pressure drop is more
D
space is limited
Question 153Single Answer
Pitot tube measures ______.
A
dynamic pressure of a moving stream
B
guage pressure
C
temperature of moving water
D
pressure difference between two fluids
Question 154Single Answer
Which of the following is not a property of an ideal fluid ?
A
flow is irrotational
B
it has no viscosity
C
it has viscosity
D
it is incompressible
Question 155Single Answer
Nozzle used in steam turbines convert ________.
A
enthalpy of steam into work
B
enthalpy of steam into kinetic energy
C
enthalpy of steam into pressure energy
D
pressure energy into work
Question 156Single Answer
Which of the following assumptions is the most relevant in air-standard cycle analysis ?
A
All the processes within the cycle are irreversible
B
Working fluid is a fixed mass
C
Specific heat of air changes during the cycle
D
Cycle is assumed to be an open cycle
Question 157Single Answer
The modern Francis turbine is a ___________flow turbine .
A
tangential
B
axial
C
radial
D
mixed
Question 158Single Answer
Variation of stress with strain rate for a Newtonian fluid is ______ .
A
hyperbolic
B
linear
C
elliptical
D
parabolic
Question 159Single Answer
Which of the following is NOT a part of refrigeration systems ?
A
Turbine
B
Evaporator
C
Compressor
D
Condenser
Question 160Single Answer
Which of the following is NOT an intensive property ?
A
Temperature
B
Total volume
C
Pressure
D
Density
Question 161Single Answer
Which of the following does NOT represent a unit of viscosity ?
A
Stoke
B
Poise
C
m²/sec
D
N-m/sec
Question 162Single Answer
__________ in the fuel is oxidised during knocking .
A
Hydrocarbon
B
Phosphorous
C
Water
D
Coal
Question 163Single Answer
_________ is defined as the ability of a material to resist deformation under action of an external load .
A
Stiffness
B
Resilience
C
Brittleness
D
Toughness
Question 164Single Answer
Draught is produced in locomotive boilers by which of the following components ?
A
Locomotive
B
Steam jet
C
Centrifugal fan
D
Chimney
Question 165Single Answer
For a steady flow, the value of all fluid properties at any fixed point _________ .
A
do not change with location
B
change with time
C
change with location
D
do not change with time
Question 166Single Answer
For a floating body, if the metacentre is below the centre of gravity, then the body is said to be __________ equilibrium .
A
thermal
B
stable
C
unstable
D
neutral
Question 167Single Answer
________ is useful for measuring flow of a conducting fluid .
A
Orifice meter
B
Rotameter
C
Vane meter
D
Electro-magnetic flow meter
Question 168Single Answer
A two- stroke engine consists of ________ port (s)
A
Three
B
Four
C
One
D
Two
Question 169Single Answer
Air Cooling is mostly preferred for _________ .
A
heavy truck
B
buses
C
moto cycles
D
multi-utility vehicles
Question 170Single Answer
_______ valves are provided in reciprocating compressors .
A
Simply supported
B
Solenoid
C
Plate
D
Poppet
Question 171Single Answer
Benson boiler have ______ water drum (s)
A
One
B
Zero
C
Three
D
Two
Question 172Single Answer
_________ is used for pumping water into a boilers .
A
Economiser
B
Duplex pump
C
Feed pump
D
Rotor
Question 173Single Answer
The function of a carburetor in internal combustion engines is :
A
to control fuel alone
B
to cool exhaust gases
C
to maintain air-fuel ratio
D
to control air alone
Question 174Single Answer
The device which transfers energy from the ______ to _____ the is known as hydraulic turbine .
A
atmosphere; fluid
B
rotor; fluid
C
fluid; rotor
D
fluid; atmosphere
Question 175Single Answer
The flash chamber in the single stage VCR cycle serves to ________ .
A
decrease the compression ratio
B
increase the refrigerating effect
C
increase the compression ratio
D
decrease the refrigerating effect
Question 176Single Answer
Define thermodynamics .
A
It is a science which deals with the relation between heat, work and properties of systems
B
It is a science which deals with work done
C
It deals with dynamics under thermal conditions
D
It is science which deals with the relation between work and properties
Question 177Single Answer
Which of the following statements is correct about a Benson boiler ?
A
Air is sent through the same direction
B
There is no recirculation of water
C
Steam is sent out in multiple directions
D
Flue gases pass only in one direction
Question 178Single Answer
Within a refrigeration system, the expansion valve is incorporated between the ________ .
A
Super-heater and sub-cooler
B
compressor and condenser
C
evaporator and compressor
D
condenser and evaporator
Question 179Single Answer
The reversed ______ cycle employed for passenger aircraft systems .
A
Carnot
B
Atkinson
C
Ericsson
D
Brayton
Question 180Single Answer
Fusible plug in a steam boiler is placed ______ .
A
below the water level indicator
B
at he crown of the furnace
C
at the fire grate of the boiler
D
near the manhole
Question 181Single Answer
Aqua ammonia solution used in a vapour absorption refrigeration system is a solution of ammonia in ________ .
A
CF3
B
LiBr
C
H2O2
D
H2O
Question 182Single Answer
Coated electrodes are used in ______ .
A
gas tungsten arc welding
B
submerged arc welding
C
tungsten insert gas welding
D
shielded metal arc welding
Question 183Single Answer
Where is air cycle refrigeration commonly used ?
A
Domestic refrigerator
B
Cold storage
C
Aircraft conditioning
D
Car air conditioning
Question 184Single Answer
________, is not a water tube boiler .
A
Benson boiler
B
Babcock-Wilcox boiler
C
Stirling boiler
D
Scotch marine
Question 185Single Answer
Stoke is another unit of -
A
kinematic viscosityy
B
velocity gradient
C
Shear stress
D
dynamic viscosit
Question 186Single Answer
For a refrigerating machine, capacity is expressed as ______ .
A
the lowest temperature attained
B
inside volume of the cabinet
C
gross weight of the machine
D
rate of heat extraction from the space being cooled
Question 187Single Answer
The value of quality or dryness fraction of a substance in saturated liquid-vapor mixture is ________ .
A
1
B
2
C
Zero
D
between Zero and 1
Question 188Single Answer
Uniform flow is the type of flow where in velocity at any given time ________- with respect to space .
A
Decreases
B
Does not change
C
Increases
D
Changes
Question 189Single Answer
______ falls under the category of a water tube boiler .
A
Locomotive boiler
B
Lancashire boiler
C
Cornish boiler
D
LaMont boiler
Question 190Single Answer
Chaplets are used in ________ .
A
forging
B
casting
C
welding
D
extrusion
Question 191Single Answer
Which of the following is NOT a unit of pressure ?
A
Pa
B
Bar
C
N/m²
D
Joule
Question 192Single Answer
What was the first refrigerant used in continuous refrigeration system ?
A
Ammonia
B
Water
C
Air
D
Carbon dioxide
Question 193Single Answer
For a 2 m deep swimming pool, pressure difference between the top and the bottom of the pool is ________ kPa .
A
22
B
19.6
C
11
D
12
Question 194Single Answer
Pressure measurement is done by ____. by measuring heat loss from a heated wire .
A
A pirani gauge
B
a manometer
C
a barometer
D
an orifice meter
Question 195Single Answer
In the Rankine cycle, the fluid which enters the boiler is :
A
water
B
steam
C
mercury
D
oxygen
Question 196Single Answer
Percentage elongating measured during tensile testing indicates _____ .
A
malleability
B
fatigue strength
C
creep
D
ductility
Question 197Single Answer
For a given centrifugal pump, discharge varies _______ with speed .
A
fifth power of
B
linearly
C
inversely
D
square root of
Question 198Single Answer
Foaming is a phenomenon that occurs in the boiler feed water due to _____ .
A
nitrogen peroxide
B
manganese
C
sodium chloride
D
oil
Question 199Single Answer
Compounding of a steam turbine is done to ______ .
A
balance the rotor
B
reduce the rotor speed
C
reduce the blade friction
D
connect the shaft
Question 200Single Answer
Any change in entropy could be achieved by changing______ .