What will be the depth of penetration of the plunger in Vicat Apparatus (IS : 5513 - 1976) from the bottom of the Vicat Mould, when the cement paste is tested for standard consistency, according to IS 4031 β 1988 ?
A
11 to 15 mm
B
8 to 10 mm
C
15 to 17 mm
D
5 to 7 mm
Question 2Single Answer
Two sewer pipelines A and B (having the same diameter and made of the same material) are laid at a bed slope of 1 in 225 and 1 in 625, respectively. Determine the ratio of their carrying capacities (QA to QB) .
A
B
C
1
D
Question 3Single Answer
Select the correct statement with respect to an over - reinforced cement concrete section under the working stress method .
A
The compressive stress in steel reaches the allowable limit before the maximum tensile stress in concrete reaches the allowable limit
B
Tensile steel stress and maximum compressive stress in concrete simultaneously reach their allowable limits
C
The allowable limiting stress is reached in concrete before the steel stress reaches the limiting value
D
The tensile stress in steel reaches the allowable limit before the maximum compressive stress in concrete reaches the allowable limit
Question 4Single Answer
A cantilever beam of span L is built - in at the support. It is restrained against lateral deflection and torsion at the free end. The effective length of compression flange for the beam as per IS 800 : 2007 is
A
0.5 L
B
0.85 L
C
2 L
D
0.75 L
Question 5Single Answer
What is the principle of plane surveying ?
A
Working from part to whole
B
Working from point to area
C
Working from angle to volume
D
Working from whole to part
Question 6Single Answer
According is IS 5968 : 1987, the minimum radius of radius of curve to be provided in the alignment of unlined canals carrying a discharge of less than 30 cumecs up to 15 cumecs is :
A
100 m
B
1000 m
C
600 m
D
150 m
Question 7Single Answer
A Pelton wheel is to be designed for a pitch diameter of 1 m and jet diameter of 0.1 m. The number of buckets on the runner computed by Taygunβs formula is :
A
20
B
25
C
15
D
10
Question 8Single Answer
What is the effect of fly ash in concrete ?
A
Reduces the secondary hydration process
B
Increases the heat of hydration
C
Increases the amount of air entrainment
D
Reduces the heat of hydration
Question 9Single Answer
As per IS 456 : 2000, the minimum grade of concrete to be used for plain concrete and reinforced concrete, respectively, in concrete works exposed directly along the sea coast are :
A
M 20 and M 30
B
M 20 and M 25
C
M 22 and M 40
D
M 15 and M 25
Question 10Single Answer
Identify the property that changes as a function of the geometrical dimensions of a section in structural materials :
A
Mass density
B
Moment of inertia
C
Poissionβs ratio
D
Modulus of elasticity
Question 11Single Answer
As per IRC (Indian Roads Congress) recommendation, what will be the designed stopping sight distance (in metres) at the vehicle speed of 80 km/h on a rural highway ?
A
120
B
140
C
70
D
60
Question 12Single Answer
No deduction is made in the quantity estimation for plastering work in cement mortar for openings having size up to :
A
0.5 m2
B
1.0 m2
C
3 m2
D
0.75 m2
Question 13Single Answer
What is the height of slump cone mould used for testing the workability of the concrete ?
A
20 cm
B
10 cm
C
30 cm
D
25 cm
Question 14Single Answer
Select the correct option with regard in the following statements (S1, S2) pertaining to pavements .
S1 : Present serviceability index is used for the functional evaluation of pavement surface condition
S2 : Rigid pavements are less affected by temperature variations than flexible pavements
A
Statements S1 is true and Statement S2 is false
B
Both statements S1 and S2 are false
C
Statements S1 is false and Statement S2 is true
D
Both statements S1 and S2 are true
Question 15Single Answer
If the quadrantal bearing of a line AB is S 31'35' E, then its whole circle bearing is equal in :
A
121o25'
B
148o25'
C
58o25'
D
211o25'
Question 16Single Answer
The overflowing sheet of water on a weir is called :
A
creek
B
crest
C
limp
D
nappe
Question 17Single Answer
According to IS 456 - 2000, what is the slump of a medium degree of workability of concrete if planed in heavily reinforced sections like slabs, beams, walls, columns ?
A
10 - 25 mm
B
25 - 50 mm
C
0 - 10 mm
D
50 - 100 mm
Question 18Single Answer
Which of the following is Kharif season in India ?
A
March / April to June / July
B
December / January to April / May
C
May / June to October / November
D
October / November to April / May
Question 19Single Answer
The estimated value of a built - up property at the end of its useful life without dismantled is called :
A
market value
B
book value
C
scrap value
D
salvage value
Question 20Single Answer
The amount of cement required for 100 m2 area, of damp proof course with 2.5 cm thinkness, in with proportion of 1: 2 : 4 (cement : sand : aggregate) will be :
A
2.5 m2
B
0.55 m2
C
1.10 m2
D
0.25 m2
Question 21Single Answer
Select the correct statement related to increasing the carbon content in steel from 0.2 to 0.9 percent .
A
Increasing the carbon content in steel decreases the yield stress and increases the ductility
B
Increasing the carbon content in steel increases the yield stress and reduces the ductility
C
Increasing the carbon content in steel decreases the yield stress and does not affect the ductility
D
Increasing the carbon content in steel does not have any effect on the yield stress or ductility
Question 22Single Answer
Which of the following laws states that pressure or intensity of pressure at a point is static fluid is equal in all directions ?
A
Newton's law
B
Pascal's law
C
Darcy's law
D
Hydrostatic law
Question 23Single Answer
The determination of plasticity index and the percentage by weight of clay mineral finer than 2 Β΅ present in the soil were done for two soil samples A and B. The ratio of plasticity index to the percentage of clay size particle for the samples A and B are given in the table .
Soil sampleΒ Β Β Ratio of plasticity index to percentage of clay size particle
Sample AΒ Β Β Β Β Less than 0.75
Sample BΒ Β Β Β Β Greater than 1.25 The two soil sample A and B are classified as
A
Sample A : Inactive; Sample B : Active
B
Sample A : Active; Sample B : Normal
C
Sample A : Active; Sample B : Inactive
D
Sample A : Normal ; Sample B : Inactive
Question 24Single Answer
Which of the following compounds of cement is responsible for early strength ?
A
C4AF
B
C3S
C
C3A
D
C2A
Question 25Single Answer
According to SP : 27 - 1984, the thickness of slab or RC slab shall be measured to the nearest of :
A
0.0002 m
B
0.005 m
C
0.0001 m
D
0.01 m
Question 26Single Answer
Classify the following pollutants as primary pollutants (PP) and secondary pollutants (SP). Ozone, Carbon monoxide, Particulate matter, photochemical smog, Nitrogen oxides, Aerosol/mist, Hydrocarbons, Perory - Acetyl - Nitrate, Sulphur dioxide.
bulk unit weight of a soil when it is fully saturated
B
saturated bulk unit weight to total void
C
total void to saturated bulk unit weight
D
total void to saturated bulk unit weight
Question 28Single Answer
Identify the test to be conducted for the determination of the modulus of subgrade reaction in pavement design .
A
Plate bearing test
B
Triaxial test
C
CBR test
D
Direct shear test
Question 29Single Answer
In limit state design, the design bond stress for deformed bars (conforming to IS 1786) for M20 concrete mentioned in IS 456 : 2000 is (in N/mm2 units) :
A
1.2
B
1.8
C
1.68
D
1.92
Question 30Single Answer
Which of the following can be considered as a taking off point in road planning in India ?
A
Lucknow plan
B
Delhi plan
C
Bombay plan
D
Nagpur plan
Question 31Single Answer
The following two statements pertain to a simply supported under reinforced concrete beam. Select the correct option with regard is these statements .
1. The failure of the beam takes place due to the yielding of steel .
2. The moment of resistance of the beam is more than that of the balanced section of the beam .
A
Statement 1 is true but Statement 2 is false
B
Statement 1 is false but Statement 2 is true
C
Both statement 1 and 2 are true
D
Both statement 1 and 2 are false
Question 32Single Answer
A continuous beam ABC with span AB = BC = L is shown in the figure. Support A is fixed type, and supports B and C are roller type. The kinematic indeterminacy of the beam is :
A
2
B
3
C
5
D
4
Question 33Single Answer
The soils transported and deposited by a river or a stream care called :
A
aeolian soils
B
alluvial soils
C
lacustrine soils
D
marine soils
Question 34Single Answer
What is the mechanical extra widening required for a two-lane pavement of width 7 m on a horizontal curve of radius 250 m, if the longest wheel base of a vehicle expected on the road is 5 m with a design speed of 70 km/h ?
A
0.155 m
B
0.225 m
C
0.100 m
D
0.552 m
Question 35Single Answer
The following are some of the errors that area associated with a total station survey work. Vertical collimation error, Centering error, Horizontal collimation error, Eccentricity error Categorize the given errors as those due to temporary adjustments (T) and permanent adjustments (P).
A
T : Vertical collimation error, Horizontal collimation error
P : Centering error, Eccentricity error
B
T : Centering error, Horizontal collimation error, Eccentricity error
P : Vertical collimation error
C
T : Eccentricity error, Horizontal collimation error
P : Centering error, Vertical collimation error, Eccentricity error
D
T : Centering error
P : Vertical collimation error, Horizontal collimation error, Eccentricity error
Question 36Single Answer
According to IS 800 : 2007, identify the property which is considered as a mechanical property of structural steel, important in design .
A
Unit mass
B
Maximum percent elongation on a standard gauge length
C
Co - efficient of thermal expansion
D
Poisson ration
Question 37Single Answer
Which of the following methods is NOT used for measuring air content in fresh concrete ?
A
Blaine air permeability method
B
Gravimetric method
C
Pressure method
D
Volumetric method
Question 38Single Answer
Which of the following methods is NOT used for the calculation of depreciation of a structure ?
A
Straight line method
B
Quantity survey method
C
Geometric projection method
D
Declining balance method
Question 39Single Answer
The failure of an over reinforced concrete beam is due to :
A
compression failure
B
mid failure
C
shear failure
D
tension failure
Question 40Single Answer
In which type of estimate is 'Court yard' NOT considered ?
A
Unit rate estimate
B
Plinth area estimate
C
Lump sum estimate
D
Cub rate estimate
Question 41Single Answer
Match the items in List 1 (name of quantities) with those in List 2 (unit of quantities in the SI system). Use codes in List for matching .
List 1Β Β Β Β Β Β Β Β Β Β Β Β Β Β Β Β Β Β List 2
M. Dynamic viscosityΒ Β Β Β Β 1. N/m
N. Kinematic viscosityΒ Β Β Β 2. N.m
O. Surface tensionΒ Β Β Β Β Β Β 3. N.s/m2
P. EnergyΒ Β Β Β Β Β Β Β Β Β Β Β Β Β 4. m2/s
A
M-3, N-4, O-2, P-1
B
M-3, N-4, O-1, P-2
C
M-4, N-3, O-1, P-2
D
M-2, N-4, O-1, P-3
Question 42Single Answer
A reinforced concrete beam is subjected to the following bending moments .
Moment due to dead load = 50 kNm
Moment due to live load = 50 kNm
Moment due to seismic load = 20 kNm
The design bending moment for limit state of collapse is :
A
120 kNm
B
180 kNm
C
144 kNm
D
150 kNm
Question 43Single Answer
In a workshop shade, trusses are spaced at 4 m centre to centre. The purlins are spaced at 1.4 m centre to centre along the slope of 300. The (Dead Load + Live load) is 3 kNm2 and the wind load in 5 kNm2. The vertical and the inclined point loads, respectively, will be :
A
14.54 kN and 28 kN
B
17.8 kN and 48 kN
C
20 kN and 24 kN
D
18 kN and 21 kN
Question 44Single Answer
What will be the percentage of passing aggregate for the grading zone 1 of sieve size 1.18 mm ?
A
100%
B
10% - 20%
C
7% - 25%
D
30% - 70%
Question 45Single Answer
The annual or periodical payment for repayment of the capital amount invested on a property for a specified period is known as :
A
depreciation
B
obsolescence
C
amortization
D
annuity
Question 46Single Answer
Among the following river training works, which are aligned either parallel or at an angle to the banks, identify the one having a difference in alignment when compared to others :
A
Flood walls
B
Guide banks
C
Groynes
D
Levees
Question 47Single Answer
The test commonly to determine the grade of bitumen in terms of its hardness is :
A
the penetration test
B
the ductility test
C
the softening point test
D
the flash and fire point test
Question 48Single Answer
A level section has formation width of 10 m, side slope of 1 : 2 (vertical : horizontal) and central height of 2 m. Determine the quantity of earthwork required for a 1 km length of formation (in m3) .
A
24,000
B
20,000
C
18,000
D
28,000
Question 49Single Answer
Which type of odour characteristic is NOT used for classifying odour of a given water sample as per IS 3025 (part-5) 1983 ?
A
Degree of sweetness
B
Degree of turbidity
C
Degree of pungency
D
Degree of smokiness
Question 50Single Answer
The liquid limit and plastic limit of clay materials is 45% and 25% respectively, what is the activity of clay materials if 20% by weight of particles of size less than 2 microns ?
A
0
B
2
C
3
D
1
Important Questions Package
TNPSC Field Surveyor, Draftsman Exam Online Question Bank Package
Buy TNPSC Field Surveyor, Draftsman Important Questions, MCQ, question answer in Hindi & English. It will help you to score high marks in TNPSC Field Surveyor, Draftsman question bank 2026 in Online, PDF & Print study material.
+ Free Monthly Current Affairs, GK & more PDF Download
Sr.
Package Name
Amount
1.
TNPSC Field Surveyor, Draftsman (Paper-I) Exam - English
Description : 1000 Quetion with Answer.
βΉ101[βΉ500]
2.
TNPSC Field Surveyor, Draftsman (Paper-I) Exam - English
Description : 1500 Question with Answer.
βΉ131[βΉ500]
3.
TNPSC Field Surveyor, Draftsman (Paper-II) PART B Exam - English
Description : 1000 Question with Answer.
βΉ101[βΉ500]
4.
TNPSC Field Surveyor, Draftsman (Paper-II) PART B Exam - English
Description : 2000 Question with Answer.
βΉ151[βΉ500]
5.
TNPSC Field Surveyor, Draftsman (Paper-I) Exam - English
Description : 1000 Question & Answer Download in PDF (Send by Email)
βΉ151[βΉ450]
6.
TNPSC Field Surveyor, Draftsman (Paper-II) PART B Exam - English
Description : 1000 Question & Answer Download in PDF (Send by Email)
βΉ151[βΉ450]
7.
TNPSC Field Surveyor, Draftsman (Paper-I) Exam Question Bank Book - English
Description : 1000 Question with Answer (Printed Material)
βΉ390[βΉ600]
8.
TNPSC Field Surveyor, Draftsman (Paper-II) PART B Exam Question Bank Book - English
Description : 1000 Question with Answer (Printed Material)
βΉ390[βΉ600]
9.
TNPSC Field Surveyor, Draftsman Exam Paper I - English (Old)
Description : 500 Question With Answer
βΉ131[βΉ500]
Draughtsman
Question 51Single Answer
Among the following corrections applied for tape measurement, identify the correction which is NOT always negative in sign :
A
Sag
B
Slope of taype
C
Pull
D
Wrong alignment
Question 52Single Answer
A village has a population of 200 with as average rate of water demand as 100 litre per capita per day. A rapid sand filter having an average filtration rate of 100 litre/hour/m2 is to be designed for water treatment. The area of rapid sand filter required is : (Take the ratio of maximum demand to average demand as 1.5.)
A
8.00 m2
B
14.50 m2
C
10.00 m2
D
12.50 m2
Question 53Single Answer
If the bearing of the side AB of a regular hexagon traverse ABCDFFA shown in the figure is 36o45', the bearing of the adjacent side BC of the traverse is :
A
216o15'
B
96o45'
C
83o15'
D
156o45'
Question 54Single Answer
Pigment volume concentration (PVC) of paint is defined as :
A
B
C
D
Question 55Single Answer
The Indian Roads Congress (IRC) was founded in the year :
A
1927
B
1934
C
1950
D
1982
Question 56Single Answer
In a leveling survey work, the first staff reading taken in a staff station after shifting the instrument and the last staff reading taken to a staff sation before the instrument in shifted are, respectively :
A
back sight and intermediate sight
B
intermediate sight and back sight
C
back sight and fore sight
D
fore sight and back sight
Question 57Single Answer
Which of the following Indian Standard Codes provides conservatively imposed loads for buildings and structures ?
A
IS 875 (part 4) β 1987
B
IS 875 (part 1) β 1987
C
IS 875 (part 3) β 1987
D
IS 875 (part 2) β 1987
Question 58Single Answer
Activity of soil is ratio of the plasticity index to :
A
percentage of compressive strength
B
percentage by weight of clay fraction
C
liquidity index
D
percentage of sensitivity
Question 59Single Answer
Kor watering in irrigation is defined as :
A
the first watering which is given to seeds sown in the plot for germination
B
the first watering which is given to a crop when the crop is a few centimeters high
C
the first watering which is given to a crop before transplanting
D
the first watering which is given to a plot when the crop is transplanted
Question 60Single Answer
What is a SI unit for dynamic viscosity ?
A
Pascal second
B
Pascal
C
Stoke
D
Newton
Question 61Single Answer
Arrange the following building materials in the increasing order of density of materials .
Granite, Steel, River sand, Water
A
Water, River sand, Steel, Granite
B
River sand, Granite, Water, Steel
C
River sand, Water, Granite, Steel
D
Water, River sand, Granite, Steel
Question 62Single Answer
The bearing of a line AB is 150o15' and the angle ABC between line AB and BC is 110o30' as shown in the given figure . What is the bearing of line BC ?
A
440o45'
B
80o45'
C
79o15'
D
330o15'
Question 63Single Answer
Select the correct statement with respect to a slow sand filter :
A
The filtering medium has effective size 0.45 to 0.7 mm, uniformity coefficient 1.3 to 1.7, multiple graded layers of sand with bacteria and odour removal
B
The rate of filtration is in the range of 100 - 150 m3/m2/day
C
The effective size of sand particles shall be 0.15 to 0.3 mm, and their uniformity coefficient shall be preferably below 3
D
Backwashing daily or on alternate days is necessary for cleaning
Question 64Single Answer
What will be the carrying capacity of a horizontal rectangular channel 4 m wide, conveying a discharge of 1 cumecs per meter width of channel ?
A
4.000 m3/s
B
2.085 m3/s
C
1.000 m3/s
D
8.000 m3/s
Question 65Single Answer
Select the correct option with regard to the following statements (S1, S2) pertaining to consolidation in soils :
S1: A soil is termed as normally consolidated, if the present effective orver burden pressure is less than maximum to which the soil was ever been subjected to in the past .
S2: The large the value of co - efficient of consolidation, the shorter it takes for full consolidation to occur .
A
S1 is true and S2 is false
B
Both S1 and S2 are false
C
Both S1 and S2 are true
D
S1 is false and S2 is true
Question 66Single Answer
A real fluid in which the shear stress is directly proportional to the velocity gradient is known as :
A
non - newtonian fluid
B
newtonian fluid
C
ideal fluid
D
plastic fluid
Question 67Single Answer
An airport runway fill needs 8,50,000 m3 of soil compacted to void ratio of 0.7. The required soil is to be taken from a borrow pit having an in situ void ratio of 0.8. If the transportation cost is Rs.10 per m3, estimated cost for the filling work is (in Rs.) :
A
82,00,000
B
90,00,000
C
50,00,000
D
85,00,000
Question 68Single Answer
If p is internal pressure, d is diameter and t is thickness of wall for a thin cylindrical shell, then the value of hoop stress will be :
A
pt/4d
B
pd/4t
C
pd/2t
D
td/4p
Question 69Single Answer
As per IS 800 : 2007, in the design of beams/plate girders, when the web of a member acting alone is inadequate, different types of stiffeners are provided. Match the type of stiffeners provided in List 1 with the requirement to be satisfied by them in List 2 .
(Use the Code in the lists for matching)
List 1Β Β Β Β Β Β Β Β Β Β Β Β Β Β Β Β Β Β Β Β Β Β Β Β Β Β Β Β Β Β Β Β Β Β Β Β Β Β Β Β List 2
B. Intermediate transverse wed stiffenerΒ Β Β Β Β 1. Provide local reinforcement to wed under shear and bearing
C. Load carrying stiffienerΒ Β Β Β Β Β Β Β Β Β Β Β Β Β Β Β 2. Improve the buckling strength of a slender Web due to shear
D. Bearing stiffenerΒ Β Β Β Β Β Β Β Β Β Β Β Β Β Β Β Β Β Β Β Β 3. Prevent local buckling of web due to concentrated loading
E. Diagonal stiffenerΒ Β Β Β Β Β Β Β Β Β Β Β Β Β Β Β Β Β Β Β 4. Prevent local crushing of web due to concentrated loading
A
B - 3, C - 2, D - 4, E - 1
B
B - 4, C - 3, D - 1, E - 2
C
B - 2, C - 3, D - 4, E - 1
D
B - 4, C - 3, D - 2, E - 1
Question 70Single Answer
A canal was designed for a full supply discharge of 60 cumee. The average supply discharge in the canal is 40 cumee. The capacity factor of the cannal is :
A
6.0
B
4.00
C
0.67
D
0.45
Question 71Single Answer
Sewers must be checked for minimum velocities at their minimum hourly flows which is equal to :
A
1/4 average daily flows
B
1/2 average daily flows
C
average daily flows
D
1/3 average daily flows
Question 72Single Answer
What is the permissible limit of organic mater present in water for mixing concrete as per IS 456 - 2000 ?
A
200 mg/ l
B
3000 mg/ l
C
2000 mg/ l
D
400 mg/ l
Question 73Single Answer
A horizontal pipeline AB of diameter d cpmveus water, flowing from A to B. The U - tube manometer with mercury as manometric liquid can be used for the measurement of :
A
difference in the total energy between two points A and B
B
difference in the pressure head between two points A and B
C
difference in the velocity between the points A and B
D
difference in the kinetic head at the two points A and
Question 74Single Answer
A cantilever of beam span l is fixed at one end, the other end resting freely on the middle of a simply supported cross-beam of the same span and section. If the cantilever beam is now loaded with a uniform load of w per unit length, find the reaction at the free end offered by the cross beam.
A
B
C
D
Question 75Single Answer
Select the INCORRECT obstacle in chaining in a chain survey:
A
Obstracle to ranging only
B
Obstracle to chanining only
C
Obstracle to plotting
D
Obstracle to chanining and ranging
Question 76Single Answer
The basis for classification of ordinary Portland cement (OPC) as grade 33, 43 and 53 as per IS 10262 is :
A
28 days compressive strength
B
fineness value and setting time
C
soundness value
D
setting time
Question 77Single Answer
The mass of a chunk of moist soil is 20 kg and its dry density is 1500 kg/m3. What is the void ratio of the soil if the specific gravity is 2.50 and density of water is 10000 kg/m3
A
66.67%
B
72.35%
C
44.45%
D
56.67%
Question 78Single Answer
The maximum effective slenderness ratio for the compression flange of a steel beam against lateral torsional bucking as per IS 800 - 2007 is :
A
400
B
180
C
250
D
300
Question 79Single Answer
As old building has a future life of 15 years. The rate of interest on capital is 7%. If the coefficient of annual sinking fund is 0.43, then what will be value of year's purchase?
A
4
B
3
C
2.36
D
2
Question 80Single Answer
The value used for the prevention of reversal of flow in a pipeline is :
A
an air value
B
a check
C
a scour value
D
a butterfly value
Question 81Single Answer
In earthquake resistant design, response reduction factor (R) for steel special moment resisting frame (SMF) design as per IS 800 : 2000 is :
A
1.5
B
5.0
C
1.0
D
2.5
Question 82Single Answer
In mix design for M25 concrete, the assumed standard deviation for estimation of target mean strength of concrete mix, as recommended by IS 456 : 2000 is (in N/mm2) :
A
5.0
B
4.5
C
3.5
D
4.0
Question 83Single Answer
Which of the following CANNOT be considered as a hard surface lining of cannal ?
A
Boulder lining
B
Soil cement lining
C
Asphaltic concrete lining
D
Plaster lining
Question 84Single Answer
The following radings were obtained during differential leveling.
Reduced Level (RL) of point A is 240.000 m. The fore sight and back sight between points A and TPI in 1.420 m and 2.024 m, respectively. Fore sight and back sight between points TP1 and TP2 is 2.100 m and 1.986 m, respectively. The back sight from B is 1.722 m. These are marked on the givenfigure. What is the RL at turning point β 2 (TP2)? All values are in meteres.
A
242.024
B
241.202
C
240.604
D
240.490
Question 85Single Answer
Which of the following actions is NOT a permanent adjustment in case of trasit theodolite ?
A
Axis of the telescope levewl adjusted to paralled to the line of collimation
B
Axis of the plate level adjusted to perpendicular to vertical axis
C
Bringing the vertical axis of the theorolite exactly over the station mark
D
Horizontal axis is perpendicular to vertical axis when the instrument is levelled
Question 86Single Answer
Which of the following actions is NOT a permanent adjustment in case of trasit theodolite ?
A
Axis of the telescope levewl adjusted to paralled to the line of collimation
B
Axis of the plate level adjusted to perpendicular to vertical axis
C
Bringing the vertical axis of the theorolite exactly over the station mark
D
Horizontal axis is perpendicular to vertical axis when the instrument is levelled
Question 87Single Answer
The ability of a material in endure alternate wet and dry conditions for a long period without considerable deformation and loss of mechanical strength is called :
A
chemical resistance
B
fire resistance
C
weathering resistance
D
frost resistance
Question 88Single Answer
A newly built hose is let out for a rent of Rs. 1,000 per month inclusive of all taxes. If outgoings are at 20% of the gross rent and expected rate of return is 10%, what is the capital value by the rental method of valuation ?
A
Rs. 99,600
B
Rs. 1,12,300
C
Rs. 87,600
D
Rs. 96,000
Question 89Single Answer
What is the approximate composition of silicon dioxide (SiO2) present in ordinary Portland cement ?
A
60 - 67%
B
17 - 25%
C
40 - 50%
D
3 - 8%
Question 90Single Answer
The following statements (C1, C2, C3, C4) pertain in the characteristics of different type of canals. Which of the following statements is/are correct ?
C1 : A contour canal can irrigate command areas on both the banks.
C2 : If is possible to constract a contour canal with banks on one side only
C3 : In the case of a ridge canal, the number of cross drainage works are maximum.
C4 : Side slope canal is aligned roughly at right angles to the ground contours.
A
C1 only
B
C2 and C4 only
C
C1, C3 and C4 only
D
C1 and C3 only
Question 91Single Answer
In an incompressible static flaid column, the rate of increase of pressure in the vertical direction is equal to weight density of fluid at that point. Which of the following is the law for this statements.
A
Bernoulli's law
B
Viscosity law
C
Hydrostatic law
D
Pascal's law
Question 92Single Answer
A construction firm has estimate a net annual rent of Rs. 90,000 on a building, at the prevailing annual rate of interest of 9%. If the annual interest rate is revised to 5%, determine the increase in the capitalized value of the property.
A
Rs. 22,50,000
B
Rs. 8,00,000
C
Rs. 10,00,000
D
Rs. 18,00,000
Question 93Single Answer
. Which constituent in cemnt is to be kept minimum to avoid a sulphate attack ?
A
C2A
B
C3S
C
C3A
D
C2 AF
Question 94Single Answer
The saturation capacity, field capacity and the permanent wilting point of a soil are 47%, 27% and 14%, respectively. The available moisture for the crops grown in the soil is:
A
13%
B
27%
C
20%
D
33%
Question 95Single Answer
On a right angle two - lane road intersection with two-way traffic, the total number of potential conflict points are:
A
24
B
44
C
18
D
32
Question 96Single Answer
Which of the following methods is NOT used for finding deflection of beam ?
A
Moment area method
B
Castigliano's method
C
strain energy method
D
Moment distribution method
Question 97Single Answer
Two centrifugal pumps P and R are available for use in a pipe flow system and their head - discharge characteristics are as follows. The following statements (S1, S2 and S3) pertain to the head and discharge values during actual operation. Neglect looses in the system. Which of the following statements are correct ?
S1 : When the two pumps P and R are connected in paralled, the discharge is 0.36 cumecs corresponding to a head 35 m.
S2 : When the two pumps P and R are connected in paralled, the discharge is 0.36 cumecs corresponding to a head 70 m.
S3 : When the two pumps P and R are connected in series.
The discharge is 0.3 cumecs corresponding to a head 46 m.
A
S2 and S3
B
S2 only
C
S1 and S3
D
S1 and S2
Question 98Single Answer
As per IS 1742 - 1983 normally a sewer shall be designed for discharging ____ times the dry-weather flow flowing half-full with a minimum self-cleansing velocity of ____.
A
three; 0.75m/s
B
four; 1.75m/s
C
two; 0.5m/s
D
five; 2.4m/s
Question 99Single Answer
The determination of shear strength of a soft staturated clay deposit in the filed can be done by :
A
the tri - axial test
B
the vane shear test
C
the unconfined compression test
D
the direct shear test
Question 100Single Answer
The total unit weight of the glacial outwash soil is 5 kN/m3. The water content in the soil is 17%. Find dry unit weight :
A
4.27 kN/m3
B
0.29 kN/m3
C
3.40 kN/m3
D
6.27 kN/m3
Question 101Single Answer
What is the purpose of enlarging a scale in drafting ?
A
To fit a larger area on a smaller paper
B
To make the map more aesthetically pleasing
C
To decrease the level of detail
D
To depict smaller objects more clearly
Question 102Single Answer
When a drawing is reduced in scale, what happens to the size of the objects depicted ?
A
They become larger
B
They remain the same size
C
They become smaller
D
They are removed from the drawing
Question 103Single Answer
What is the purpose of a base map in cartography and surveying ?
A
To display artistic designs
B
To indicate political boundaries
C
To provide a foundation for additional map layers
D
To predict weather patterns
Question 104Single Answer
What is the purpose of dimensioning in a technical drawing ?
A
To add visual appeal
B
To indicate the scale
C
To communicate size and location
D
To show the perspective
Question 105Single Answer
Which surveying technique involves directly measuring distances, angles, and elevation on the ground ?z
A
Remote sensing
B
Photogrammetry
C
Aerial photography
D
Physical survey
Question 106Single Answer
What does the term "plan preparation" refer to in the context of cartography and surveying ?
A
Designing interior decor
B
Creating floor plans for buildings
C
Developing marketing plans
D
Plotting geographic data on a map
Question 107Single Answer
Which type of line is used to represent visible edges in a technical drawing ?
A
Hidden line
B
Center line
C
Extension line
D
Object line
Question 108Single Answer
How does aerial photography contribute to mapmaking and surveying ?
A
By predicting future population growth
B
By analysing social media trends
C
By providing high-resolution images of Earth's surface from above
D
By designing fashion accessories
Question 109Single Answer
What is the primary purpose of using scales in technical drawings ?
A
To measure angles
B
To calculate volume
C
To represent different proportions
D
To indicate the type of line used
Question 110Single Answer
What is photogrammetry ?
A
A technique for predicting earthquakes
B
A method of analyzing social media posts
C
The process of extracting measurements from aerial photographs
D
A method of predicting climate change
Question 111Single Answer
What is the term for the ratio between the size of an object on a map and its actual size on the ground ?
A
Scale factor
B
Ratio of enlargement
C
Scale reduction
D
Map factor
Question 112Single Answer
If a map has a scale of 1:10,000, what does this mean ?
A
1 unit on the map represents 10,000 units on the ground
B
10,000 units on the map represent 1 unit on the ground
C
10,000 units on the map represent 10,000 units on the ground
D
1 unit on the map represents 1 unit on the ground
Question 113Single Answer
In a map with a fractional scale, how is the numerator interpreted ?
A
It represents the size of objects on the ground
B
It represents the size of objects on the map
C
It indicates the distance between points on the map
D
It indicates the distance between points on the ground
Question 114Single Answer
How does remote sensing technology contribute to mapmaking and surveying ?
A
By predicting stock market trends
B
By analysing historical novels
C
By collecting data from a distance for mapping and analysis
D
By designing fashion trends
Question 115Single Answer
What is the primary purpose of a scale bar on a map ?
A
To measure distances between points
B
To determine the orientation of the map
C
To indicate the scale of the map
D
To display latitude and longitude lines
Question 116Single Answer
What is the primary purpose of photo interpretation in cartography ?
A
To analyse ancient manuscripts
B
To predict stock market trends
C
To extract meaningful information from aerial photographs
D
To design fashion trends
Question 117Single Answer
What technology is often used to capture aerial images from aircraft for mapping purposes ?
A
Telescopes
B
Cameras
C
Satellites
D
Radios
Question 118Single Answer
Which line is used to represent an edge that is not visible in a technical drawing ?
A
Hidden line
B
Center line
C
Phantom line
D
Object line
Question 119Single Answer
What is the purpose of lettering in technical drawings ?
A
To label the drawing
B
To create visual effects
C
To add color to the drawing
D
To indicate the type of scale
Question 120Single Answer
Which projection shows the front, top, and side views of an object on a single plane ?
A
Isometric projection
B
Orthographic projection
C
Perspective projection
D
Oblique projection
Question 121Single Answer
Which type of projection gives a realistic view of an object with depth perception ?
A
Isometric projection
B
Orthographic projection
C
Perspective projection
D
Planometric projection
Question 122Single Answer
What is the purpose of providing dimensions on a technical drawing ?
A
To make the drawing visually appealing
B
To indicate the type of line used
C
To specify the font size for lettering
D
To define the size and location of features
Question 123Single Answer
Which line type represents the centerline of a circular feature in a technical drawing ?
A
Hidden line
B
Center line
C
Object line
D
Phantom line
Question 124Single Answer
Which type of projection is commonly used in architectural drawings to represent walls and other features accurately ?
A
Isometric projection
B
Oblique projection
C
Orthographic projection
D
Planometric projection
Question 125Single Answer
What is the purpose of a construction line in a technical drawing ?
A
To outline the main object
B
To indicate hidden edges
C
To assist with drawing accuracy
D
To label the drawing
Question 126Single Answer
In an orthographic projection, how many views are typically shown for a three - dimensional object ?
A
1
B
2
C
3
D
4
Question 127Single Answer
Which type of line is used to show the edges of an object that are not directly visible in the current view ?
A
Object line
B
Hidden line
C
Center line
D
Extension line
Question 128Single Answer
What is the purpose of using different line weights in technical drawings ?
A
To indicate different colors
B
To show depth perception
C
To distinguish between different materials
D
To create visual hierarchy and clarity
Question 129Single Answer
What is the purpose of a leader line in dimensioning ?
A
To indicate the center of a circle
B
To show hidden lines
C
To direct the reader's attention to a specific feature
D
To indicate the angle of an object
Question 130Single Answer
Which projection method is commonly used for technical illustrations of mechanical parts ?
A
Oblique projection
B
Orthographic projection
C
Planometric projection
D
Perspective projection
Question 131Single Answer
Which type of scale maintains the proportions of the original object while reducing or enlarging it ?
A
Engineering scale
B
Architectural scale
C
Isometric scale
D
Proportional scale
Question 132Single Answer
What is the purpose of a phantom line in a technical drawing ?
A
To indicate hidden edges
B
To show the extension of an object
C
To outline the main object
D
To indicate alternate positions or paths
Question 133Single Answer
Which type of projection shows all three dimensions of an object at once, with equal foreshortening ?
A
Isometric projection
B
Oblique projection
C
Orthographic projection
D
Perspective projection
Question 134Single Answer
What is the purpose of the title block in a technical drawing ?
A
To label the drawing with the title
B
To indicate the scale used
C
To provide information about the author
D
To contain essential information about the drawing
Question 135Single Answer
In which projection method are the two frontal dimensions of an object shown in full size ?
A
Isometric projection
B
Oblique projection
C
Orthographic projection
D
Perspective projection
Question 136Single Answer
What is the purpose of a projection line in a technical drawing ?
A
To indicate the direction of the light source
B
To show hidden lines
C
To project the object onto the drawing plane
D
To connect dimensions to the object
Question 137Single Answer
Which type of scale is commonly used in civil engineering and architectural drawings ?
A
Engineering scale
B
Architectural scale
C
Metric scale
D
Proportional scale
Question 138Single Answer
What is the purpose of cross - hatching in technical drawings ?
A
To indicate the scale used
B
To create visual effects
C
To show hidden edges
D
To represent different materials or textures
Question 139Single Answer
Which type of projection is used to show a three - dimensional object in a single view ?
A
Isometric projection
B
Orthographic projection
C
Perspective projection
D
Planometric projection
Question 140Single Answer
Which type of line is used to show the centerline of a hole in a technical drawing ?
A
Hidden line
B
Object line
C
Phantom line
D
Center line
Question 141Single Answer
What does the term "foreshortening" refer to in a technical drawing ?
A
The reduction of size in an object
B
The distortion of angles
C
The bending of lines
D
The distortion of proportions due to perspective
Question 142Single Answer
What is the purpose of projection lines in a technical drawing ?
A
To indicate hidden lines
B
To show the direction of light
C
To project features onto a specific plane
D
To connect dimensions to the object
Question 143Single Answer
In technical drawings, which type of line is used to represent a cutting plane ?
A
Hidden line
B
Object line
C
Phantom line
D
Center line
Question 144Single Answer
What is the purpose of a border line in a technical drawing ?
A
To enclose the entire drawing
B
To indicate the centerline
C
To show hidden edges
D
To indicate the scale
Question 145Single Answer
Which type of scale is used for precision measurements and engineering drawings ?
A
Engineering scale
B
Architectural scale
C
Metric scale
D
Proportional scale
Question 146Single Answer
What is the purpose of an extension line in dimensioning ?
A
To extend the length of an object
B
To indicate the direction of light
C
To connect dimensions to the object
D
To show hidden lines
Question 147Single Answer
Which projection method uses a 45 - degree angle for receding lines and true dimensions for all axes ?
A
Isometric projection
B
Oblique projection
C
Orthographic projection
D
Planometric projection
Question 148Single Answer
What is the purpose of a sectional view in a technical drawing ?
A
To indicate hidden lines
B
To show internal details of an object
C
To provide dimensions
D
To indicate the centerline
Question 149Single Answer
Which type of line is used to indicate the dimensions of a feature in a technical drawing ?
A
Object line
B
Hidden line
C
Extension line
D
Center line
Question 150Single Answer
What is the purpose of a dimension line in a technical drawing ?
A
To indicate the size of an object
B
To show hidden edges
C
To indicate the centerline
D
To project the object onto the drawing plane
Question 151Single Answer
In an orthographic projection, what is the relationship between the top view and the front view ?
A
They are the same
B
The top view is rotated 90 degrees
C
The front view is rotated 90 degrees
D
They are perpendicular to each other
Question 152Single Answer
What is the purpose of using auxiliary views in technical drawings ?
A
To indicate hidden lines
B
To provide a detailed view of an angled surface
C
To show internal details
D
To indicate the scale
Question 153Single Answer
Which type of scale is typically used for architectural drawings in which one unit represents one foot or one meter ?
A
Engineering scale
B
Architectural scale
C
Metric scale
D
Proportional scale
Question 154Single Answer
Which technique involves using cameras mounted on aircraft to capture images of the Earth's surface ?
A
GIS mapping
B
Remote sensing
C
Photogrammetry
D
Physical survey
Question 155Single Answer
What is the purpose of a detail view in a technical drawing ?
A
To indicate hidden lines
B
To provide a smaller - scale view of an object
C
To show internal details
D
To indicate the centerline
Question 156Single Answer
What is the role of GIS in the techniques of preparing base maps ?
A
To predict future population growth
B
To analyse social media trends
C
To integrate and manage geographic data for map creation
D
To design fashion accessories
Question 157Single Answer
In an orthographic projection, what is the relationship between the front view and the side view ?
A
They are the same
B
The front view is rotated 90 degrees
C
The side view is rotated 90 degrees
D
They are perpendicular to each other
Question 158Single Answer
Which technique is used to create detailed elevation models and topographic maps from aerial photographs ?
A
Aerial photography
B
Remote sensing
C
Photogrammetry
D
Physical survey
Question 159Single Answer
Which line type represents the outline of a feature that is not directly visible in a particular view ?
A
Hidden line
B
Center line
C
Phantom line
D
Object line
Question 160Single Answer
What is the primary use of remote sensing in mapmaking and surveying ?
A
To predict stock market trends
B
To analyze historical novels
C
To collect data from a distance for mapping, analysis, and monitoring
D
To design fashion trends
Question 161Single Answer
What is the purpose of a section line in a technical drawing ?
A
To indicate hidden lines
B
To indicate the scale
C
To show the direction of light
D
To represent the location of a cutting plane
Question 162Single Answer
How does GIS technology contribute to spatial data analysis in mapmaking ?
A
By predicting future climate patterns
B
By analyzing social media trends
C
By providing tools for visualizing and analyzing geographic data
D
By designing fashion accessories
Question 163Single Answer
What is the main advantage of using aerial photography in mapmaking and surveying ?
A
It can predict stock market trends
B
It provides insights into personal relationships
C
It captures detailed visual information about geographic areas
D
It can forecast climate change patterns
Question 164Single Answer
Which type of line is used to indicate the edges of an object that are not visible in the current view but exist in the other views ?
A
Hidden line
B
Center line
C
Phantom line
D
Object line
Question 165Single Answer
Which method should be used to combine maps of different scales ?
A
Overlaying the maps directly
B
Cutting and pasting sections from different maps
C
Rescaling all maps to the same scale
D
Aligning the maps based on common landmarks
Question 166Single Answer
How does GIS contribute to urban planning and infrastructure design using base maps ?
A
By analyzing ancient manuscripts
B
By predicting stock market trends
C
By providing tools for spatial analysis and decision-making
D
By designing fashion trends
Question 167Single Answer
What is the purpose of an alignment line in a technical drawing ?
A
To indicate hidden lines
B
To show the direction of light
C
To align different views of an object
D
To project the object onto the drawing plane
Question 168Single Answer
Which technology is often used to capture detailed elevation data for creating topographic maps ?
A
GPS
B
GIS
C
LiDAR
D
Remote sensing
Question 169Single Answer
In a technical drawing, what is the purpose of a break line ?
A
To indicate hidden edges
B
To show the direction of light
C
To break a long object for drawing convenience
D
To project the object onto the drawing plane
Question 170Single Answer
Which projection method is used to represent an object by projecting points from different directions ?
A
Isometric projection
B
Oblique projection
C
Orthographic projection
D
Perspective projection
Question 171Single Answer
What is the purpose of a scale reference line in a technical drawing ?
A
To indicate hidden lines
B
To indicate the scale
C
To align different views of an object
D
To provide dimensions
Question 172Single Answer
In an isometric projection, what is the angle between the axes ?
A
30 degrees
B
45 degrees
C
60 degrees
D
90 degrees
Question 173Single Answer
Which type of line is used to represent a repetitive pattern in a technical drawing ?
A
Hidden line
B
Center line
C
Phantom line
D
Section line
Question 174Single Answer
Building bye-laws and development control rules are regulations that govern :
A
National politics
B
Urban planning and construction
C
Agricultural practices
D
Educational institutions
Question 175Single Answer
Which government body is responsible for formulating and implementing building bye - laws in Rajasthan ?
A
State Education Department
B
State Health Department
C
Urban Development and Housing Department
D
State Tourism Department
Question 176Single Answer
What is the primary goal of plan preparation techniques in mapmaking ?
A
To predict stock market trends
B
To analyze social media trends
C
To accurately represent geographic features on a map
D
To design fashion trends
Question 177Single Answer
What is the purpose of building bye - laws and development control rules ?
A
To restrict urban growth
B
To facilitate transparent governance
C
To encourage pollution
D
To discourage public facilities
Question 178Single Answer
What role does GPS play in physical survey techniques ?
A
It predicts climate change patterns
B
It accurately locates positions on Earth's surface
C
It analyzes historical novels
D
It designs interior decor
Question 179Single Answer
What is the term for the process of combining maps to create a larger, more detailed map ?
A
Map overlay
B
Map integration
C
Map synthesis
D
Map enlargement
Question 180Single Answer
Which of the following is NOT a common aspect covered by building bye - laws ?
A
Building height restrictions
B
Zoning regulations
C
Traffic rules
D
Fire safety measures
Question 181Single Answer
What is the main purpose of advanced techniques of aerial photography in cartography ?
A
To predict stock market trends
B
To analyze ancient manuscripts
C
To capture detailed images of Earth's surface from above
D
To design fashion trends
Question 182Single Answer
In Rajasthan, building bye - laws are intended to ensure :
A
Increase in pollution levels
B
Adherence to safety standards
C
Encouragement of illegal construction
D
Overcrowding in urban areas
Question 183Single Answer
What is the primary goal of photo interpretation in mapmaking ?
A
To predict stock market trends
B
To analyze social media trends
C
To extract meaningful information from aerial photographs
D
To design fashion trends
Question 184Single Answer
How does GIS technology assist in data integration for base map creation ?
A
By predicting future climate patterns
B
By analyzing social media trends
C
By providing tools to combine various sources of geographic data
D
By designing fashion accessories
Question 185Single Answer
When combining maps, what is the purpose of a control point ?
A
To mark the center of the map
B
To indicate the scale factor
C
To align and adjust the maps accurately
D
To provide elevation data
Question 186Single Answer
What does FSI stand for in the context of building bye - laws ?
A
Financial and Structural Incentives
B
Floor Space Index
C
Formal Safety Implementation
D
Foundation Support and Integrity
Question 187Single Answer
What is the role of remote sensing in environmental monitoring and mapmaking ?
A
By predicting stock market trends
B
By analyzing historical novels
C
By collecting data from a distance to create maps and models
D
By designing fashion trends
Question 188Single Answer
Which factor determines the permissible height of a building in building bye - laws ?
A
Population density
B
Number of windows
C
Proximity to schools
D
Availability of electricity
Question 189Single Answer
What does the term "cartographic scale" refer to ?
A
The size of the map on paper
B
The accuracy of the map's details
C
The ratio of distances on the map to actual distances on the ground
D
The type of symbols used on the map
Question 190Single Answer
Development Control Rules (DCR) primarily focus on :
A
Environmental conservation
B
Promotion of unauthorized construction
C
Traffic congestion
D
Ensuring accessibility to public facilities
Question 191Single Answer
Which map projection is commonly used for world maps and minimizes distortion near the equator ?
A
Mercator projection
B
Robinson projection
C
Azimuthal projection
D
Conic projection
Question 192Single Answer
Which of the following elements is commonly regulated by development control rules ?
A
Creation of slums
B
Landscaping of private gardens
C
Design of public monuments
D
Land use and zoning
Question 193Single Answer
What is the purpose of a "graphic scale" on a map ?
A
To display images
B
To measure angles
C
To represent physical features
D
To measure distances
Question 194Single Answer
How does GIS contribute to spatial analysis and decision-making in mapmaking and surveying ?
A
By predicting stock market trends
B
By analyzing social media trends
C
By providing tools for visualizing and interpreting geographic data
D
By designing fashion trends
Question 195Single Answer
When measuring distances using a graphic scale, what should you do if the scale is not accurate for a specific area on the map ?
A
Adjust the scale to fit the area
B
Estimate the distance visually
C
Use a different map with a suitable scale
D
Ignore the inaccuracies
Question 196Single Answer
What is the term for a map that shows a specific feature or theme, such as vegetation or population distribution ?
A
Topographic map
B
Thematic map
C
Political map
D
Relief map
Question 197Single Answer
What is the primary use of aerial photography in land use planning and urban development ?
A
It can predict stock market trends
B
It provides insights into personal relationships
C
It captures visual data for analyzing changes in land cover and development
D
It can forecast climate change patterns
Question 198Single Answer
How does remote sensing technology contribute to environmental assessment and monitoring ?
A
By predicting future population growth
B
By analyzing social media trends
C
By collecting data from a distance for analyzing changes in the environment
D
By designing fashion trends
Question 199Single Answer
What is the significance of GIS in plan preparation techniques for creating maps ?
A
To predict stock market trends
B
To analyze ancient manuscripts
C
To provide tools for accurate spatial data representation
D
To design fashion trends
Question 200Single Answer
When combining maps, why is it important to use maps with the same datum and projection ?