๐Ÿ“š Exam by Category
โ–พ
Objective Questions

Latest SAMEER Project Technical Assistant Exam Question (Objective Questions), MCQ in English

Subjects : Concerned Subject (Fitter)

Question Bank SAMEER Project Technical Assistant (Fitter) Exam - English
Back to Exam

Concerned Subject (Fitter)

Question 1Single Answer
What is the primary function of dividers in marking off?
  1. A
    Measuring and transferring distances
  2. B
    Cutting metal
  3. C
    Drilling holes
  4. D
    Filing surfaces
Question 2Single Answer
What material is commonly used for making dividers?
  1. A
    Aluminum
  2. B
    Hardened steel
  3. C
    Plastic
  4. D
    Wood
Question 3Single Answer
How should dividers be maintained to ensure accuracy?
  1. A
    Store in a humid environment
  2. B
    Apply heavy grease
  3. C
    Keep points sharp and clean
  4. D
    Leave in direct sunlight
Question 4Single Answer
What is a scribing block used for?
  1. A
    Marking lines parallel to a surface
  2. B
    Measuring angles
  3. C
    Cutting sheet metal
  4. D
    Drilling holes
Question 5Single Answer
What is the main component of a scribing block?
  1. A
    Blade
  2. B
    Scribe needle
  3. C
    Hammer
  4. D
    Protractor
Question 6Single Answer
What type of dividers are used for precise measurements?
  1. A
    Wing dividers
  2. B
    Spring dividers
  3. C
    Straight dividers
  4. D
    Flat dividers
Question 7Single Answer
How should a scribing block be stored?
  1. A
    In a damp place
  2. B
    Exposed to dust
  3. C
    In a protective case
  4. D
    Submerged in water
Question 8Single Answer
What is the classification of dividers based on their design?
  1. A
    Heavy and light
  2. B
    Single and double
  3. C
    Long and short
  4. D
    Fixed and adjustable
Question 9Single Answer
What care should be taken for dividers to prevent rust?
  1. A
    Use sandpaper
  2. B
    Store in water
  3. C
    Apply oil lightly
  4. D
    Heat regularly
Question 10Single Answer
What is the purpose of a surface plate in marking off?
  1. A
    Providing a flat reference surface
  2. B
    Cutting metal
  3. C
    Measuring angles
  4. D
    Drilling holes
Question 11Single Answer
What is the primary use of a try square?
  1. A
    Checking perpendicularity
  2. B
    Measuring lengths
  3. C
    Drilling holes
  4. D
    Cutting metal
Question 12Single Answer
What material is a try square blade typically made of?
  1. A
    Plastic
  2. B
    Hardened steel
  3. C
    Wood
  4. D
    Aluminum
Question 13Single Answer
How should a try square be maintained?
  1. A
    Store in a humid environment
  2. B
    Bend the blade slightly
  3. C
    Apply heavy grease
  4. D
    Keep blade clean and free of burrs
Question 14Single Answer
What is the function of an ordinary depth gauge?
  1. A
    Measuring angles
  2. B
    Cutting metal
  3. C
    Measuring depth of holes or recesses
  4. D
    Marking lines
Question 15Single Answer
What is the typical accuracy of a protractor?
  1. A
    10 degrees
  2. B
    0.1 degree
  3. C
    5 degrees
  4. D
    1 degree
Question 16Single Answer
How should a protractor be stored to prevent damage?
  1. A
    In a protective cover
  2. B
    In a toolbox with other tools
  3. C
    Exposed to moisture
  4. D
    In direct sunlight
Question 17Single Answer
What is the main use of a protractor in a workshop?
  1. A
    Measuring lengths
  2. B
    Drilling holes
  3. C
    Measuring angles
  4. D
    Filing surfaces
Question 18Single Answer
What is the primary component of an ordinary depth gauge?
  1. A
    Depth bar
  2. B
    Vernier scale
  3. C
    Blade
  4. D
    Protractor
Question 19Single Answer
How should a try square be checked for accuracy?
  1. A
    Compare with a known 90-degree angle
  2. B
    Bend the blade
  3. C
    Submerge in water
  4. D
    Heat the blade
Question 20Single Answer
What is the purpose of a protractorโ€™s scale?
  1. A
    Measuring depth
  2. B
    Measuring angles
  3. C
    Measuring length
  4. D
    Cutting metal
Question 21Single Answer
What is the primary use of a cold chisel?
  1. A
    Measuring lengths
  2. B
    Drilling holes
  3. C
    Cutting or chipping metal
  4. D
    Filing surfaces
Question 22Single Answer
What material is commonly used for cold chisels?
  1. A
    Aluminum
  2. B
    Wood
  3. C
    Plastic
  4. D
    High carbon steel
Question 23Single Answer
What is the typical cutting angle of a cold chisel?
  1. A
    30ยฐ
  2. B
    45ยฐ
  3. C
    90ยฐ
  4. D
    60ยฐ
Question 24Single Answer
What type of cold chisel is used for cutting grooves?
  1. A
    Cross-cut chisel
  2. B
    Flat chisel
  3. C
    Round nose chisel
  4. D
    Diamond point chisel
Question 25Single Answer
How should cold chisels be maintained to prevent damage?
  1. A
    Store in water
  2. B
    Use for prying
  3. C
    Keep cutting edge sharp and oiled
  4. D
    Heat regularly
Question 26Single Answer
What is the purpose of a diamond point chisel?
  1. A
    Cutting flat surfaces
  2. B
    Cutting V-shaped grooves
  3. C
    Cutting round holes
  4. D
    Measuring angles
Question 27Single Answer
What care should be taken when using a cold chisel?
  1. A
    Strike with a wooden hammer
  2. B
    Store in a humid environment
  3. C
    Use without a hammer
  4. D
    Wear safety goggles
Question 28Single Answer
What type of cold chisel is used for cutting keyways?
  1. A
    Flat chisel
  2. B
    Cross-cut chisel
  3. C
    Diamond point chisel
  4. D
    Round nose chisel
Question 29Single Answer
What is the cutting angle for a cold chisel used on soft metals?
  1. A
    30ยฐ
  2. B
    45ยฐ
  3. C
    60ยฐ
  4. D
    70ยฐ
Question 30Single Answer
How should a damaged cold chisel be handled?
  1. A
    Continue using it
  2. B
    Store in water
  3. C
    Discard immediately
  4. D
    Grind to restore cutting edge
Question 31Single Answer
Which tool is commonly used for marking straight lines on a metal surface?
  1. A
    Divider
  2. B
    Scriber
  3. C
    Caliper
  4. D
    Reamer
Question 32Single Answer
A scriber is generally made of:
  1. A
    Mild steel
  2. B
    Copper
  3. C
    High carbon steel
  4. D
    Aluminium
Question 33Single Answer
The point of a scriber is generally hardened and tempered so that it can:
  1. A
    Resist wear
  2. B
    Bend easily
  3. C
    Increase weight
  4. D
    Reduce length
Question 34Single Answer
Which tool is used for drawing circles and arcs on metal surfaces?
  1. A
    Try square
  2. B
    Protractor
  3. C
    Surface gauge
  4. D
    Divider
Question 35Single Answer
A divider is mainly used for:
  1. A
    Measuring temperature
  2. B
    Marking circles and transferring dimensions
  3. C
    Cutting threads
  4. D
    Grinding surfaces
Question 36Single Answer
The legs of a divider are generally made of:
  1. A
    Copper
  2. B
    Brass
  3. C
    Cast iron
  4. D
    High carbon steel
Question 37Single Answer
Which instrument is used for marking lines parallel to a datum surface?
  1. A
    Scribing block
  2. B
    Micrometer
  3. C
    Screw pitch gauge
  4. D
    Reamer
Question 38Single Answer
A scribing block is normally used on a:
  1. A
    Wooden bench
  2. B
    Surface plate
  3. C
    Welding table only
  4. D
    Grinding wheel
Question 39Single Answer
The base of a scribing block is generally made of:
  1. A
    Plastic
  2. B
    Rubber
  3. C
    Cast iron
  4. D
    Aluminium foil
Question 40Single Answer
The scriber of a scribing block can generally be:
  1. A
    Used only horizontally
  2. B
    Rotated only
  3. C
    Heated continuously
  4. D
    Adjusted vertically
Question 41Single Answer
Which tool is used to check squareness between two surfaces?
  1. A
    Try square
  2. B
    Divider
  3. C
    Outside caliper
  4. D
    Tap wrench
Question 42Single Answer
A try square normally checks an angle of:
  1. A
    30ยฐ
  2. B
    45ยฐ
  3. C
    90ยฐ
  4. D
    60ยฐ
Question 43Single Answer
The two main parts of a try square are:
  1. A
    Handle and jaw
  2. B
    Blade and stock
  3. C
    Spindle and sleeve
  4. D
    Flute and shank
Question 44Single Answer
The blade of a try square is generally made of:
  1. A
    Wood
  2. B
    Hardened steel
  3. C
    Copper
  4. D
    Zinc
Question 45Single Answer
A depth gauge is mainly used for measuring:
  1. A
    Diameter of a shaft
  2. B
    Depth of holes and recesses
  3. C
    Angle of a surface
  4. D
    Thread pitch
Question 46Single Answer
Which instrument is commonly used to measure angles directly?
  1. A
    Feeler gauge
  2. B
    Protractor
  3. C
    Plug gauge
  4. D
    Divider
Question 47Single Answer
A simple protractor is generally graduated from:
  1. A
    0ยฐ to 180ยฐ
  2. B
    0ยฐ to 90ยฐ only
  3. C
    0ยฐ to 45ยฐ
  4. D
    0ยฐ to 30ยฐ
Question 48Single Answer
Which precaution is important while using a try square?
  1. A
    Keep blade and stock clean
  2. B
    Use it as a hammer
  3. C
    Heat it before use
  4. D
    Grind the blade frequently
Question 49Single Answer
A cold chisel is used for cutting metal in the:
  1. A
    Molten state
  2. B
    Vapour state
  3. C
    Liquid state
  4. D
    Cold state
Question 50Single Answer
Cold chisels are generally made of:
  1. A
    High carbon steel
  2. B
    Lead
  3. C
    Copper
  4. D
    Aluminium
Important Questions Package

SAMEER Project Technical Assistant Exam Online Question Bank Package

Buy SAMEER Project Technical Assistant Important Questions, MCQ, question answer in Hindi & English. It will help you to score high marks in SAMEER Project Technical Assistant question bank 2026 in Online, PDF & Print study material.

+ Free Monthly Current Affairs, GK & more PDF Download
Sr.Package NameAmount
1.SAMEER Project Technical Assistant (Fitter) Exam - English
Description : 1000 Question with Answer
โ‚น101 [โ‚น500]
2.SAMEER Project Technical Assistant (Fitter) Exam - English
Description : 2000 Question with Answer
โ‚น141 [โ‚น500]
3.SAMEER Project Technical Assistant (Electronics) Exam - English
Description : 1000 Question with Answer
โ‚น101 [โ‚น500]
4.SAMEER Project Technical Assistant (Electronics) Exam - English
Description : 2000 Question with Answer
โ‚น141 [โ‚น500]
5.SAMEER Project Technical Assistant (Electronics) Exam - English
Description : 3000 Question with Answer
โ‚น171 [โ‚น500]
Back to Exam
Question for SAMEER Project Technical Assistant 2026 - Quiz / Questions / MCQ - Toppersexam