📚 Exam by Category
▾
Objective Questions

Latest SAMEER Project Engineer Exam Question (Objective Questions), MCQ in English

Subjects : Concerned Subject (Mechanical)

Question Bank SAMEER Project Engineer Exam (Mechanical Engineering) - English
Back to Exam

Concerned Subject (Mechanical)

Question 1Single Answer
Which of the following is the unit of kinematic viscosity _________________?
  1. A
    Pascal
  2. B
    Poise
  3. C
    Stoke
  4. D
    Faraday
  5. E
    None of the above
Question 2Single Answer
Consider the following motions :
1. Piston reciprocating inside an engine cylinder
2. Motion of a shaft between foot-step bearings
Which of the above can rightly be considered as successfully constrained motion?
  1. A
    1 only                     
  2. B
    2 only
  3. C
    Both 1 and 2           
  4. D
    Neither 1 nor 2
Question 3Single Answer
A rotor weighing 2 kN is supported on bearings A and B which are 1 m apart. The centre of mass of the rotor is at a distance 0.4 m from bearing A. It is observed that there is an unbalanced couple of magnitude 300 N-m which leaves the shaft balanced statically.The dynamic reactions at the supports will be
  1. A
    800 N and 800 N
  2. B
    300 N and 800 N
  3. C
    800 N and – 300 N
  4. D
    300 N and – 300 N
Question 4Single Answer
A spherical waterdrop of 1 mm in diameter splits up in air into 64 smaller drops of equal size. The surface tension coefficient of water in air is 0.073 N/m. The work required in splitting up the drop is
  1. A
    0.96 × 10–6 J            
  2. B
    0.69 × 10–6 J
  3. C
    0.32 × 10–6 J            
  4. D
    0.23 × 10–6 J
Question 5Single Answer
Consider the following statements pertaining to stability of floating bodies:
1. A floating body will be stable when the centre of gravity is above the centre of buoyancy.
2. The position of metacentres corresponding to different axes of rotation are generally different for the same floating object.
3. For cargo ships, the metacentric height varies with loading.
Which of the above statements are correct?
  1. A
    1, 2 and 3                
  2. B
    1 and 2 only
  3. C
    1 and 3 only                        
  4. D
    2 and 3 only
Question 6Single Answer
A fin will be more effective when Bio number is
  1. A
    Greater than 1
  2. B
    Equal to 1
  3. C
    Between 1 and 3
                   4        4
  4. D
    Less than 1
Question 7Single Answer
A tank of length, breadth and height in the ratio of 2:1:2 is full of water. The ratio of hydrostatic force at the bottom to that at any larger vertical surface is
  1. A
    1
  2. B
    2
  3. C
    3
  4. D
    4
Question 8Single Answer
Which of the following fluids exhibit a certain shear stress at zero shear strain rate followed by a straight line relationship between shear stress and shear strain rate?
  1. A
    Newtonian fluid 
  2. B
    Ideal Bingham plastic fluids
  3. C
    Pseudo-plastic fluids
  4. D
    Dilatent fluids
Question 9Single Answer
What is the specific gravity of a marble stone, which weighs 400N in air, and 200N in water? (g=10m/s2)
  1. A
    8
  2. B
    6
  3. C
    4
  4. D
    2
Question 10Single Answer
What is the intensity of pressure in the following SI units, when specific gravity of mercury is 13.6 and the intensity of pressure is 400KPa ?
  1. A
    0.3 bar or 4.077m of water or 0.29 mm of Hg
  2. B
    4 bar or 5.077m of water or 0.399 mm of Hg
  3. C
    0.3 bar or 5.077m of water or 0.599 mm of Hg
  4. D
    4 bar or 4.077m of water or 0.299 mm of Hg
Question 11Single Answer
Consider the following statements:
1.If a small upward displacement is given to a floating body, it results in the reduction of the buoyant force acting on the body
2.A slight horizontal displacement does not change either the magnitude or the location of the buoyant force 
Which of the above statements is/are correct? 
  1. A
    Both 1 and 2
  2. B
    1 only 
  3. C
    2 only
  4. D
    Neither 1 nor 2 
Question 12Single Answer
State whether following flow field is physically possible? 
  1. A
    Possible for steady, incompressible flow
  2. B
    Possible for unsteady, incompressible flow
  3. C
    Possible for steady, compressible flow 
  4. D
    Not Possible 
Question 13Single Answer
In a differential manometer, a head of 0.5 m of fluid A in limb 1 is found to balance a head of 0.3 m of fluid B in limb 2. The atmospheric pressure is 760 mm of mercury. The ratio of specific gravities of A to B is
  1. A
    0.25
  2. B
    0.26
  3. C
    2
  4. D
    4
Question 14Single Answer
A Reversed Carnot Engine removes 50 kW from a heat sink. The temperature of the heat sink is 250 K and the temperature of the heat reservoir is 300 K. The power required of the engine is
  1. A
    10 kW 
  2. B
    20 kW
  3. C
    30 kW
  4. D
    50 kW
Question 15Single Answer
On which of the following just in time manufacturing philosophy emphasizes ?
  1. A
    man power
  2. B
    profit
  3. C
    inventory
  4. D
    manufacturing
Question 16Single Answer
In a stream line steady flow, two points A and B on a stream line are 1m apart and the flow velocity varies uniformly from 2m/s to 5m/s. What is the acceleration of fluid at B?
  1. A
    3 m/s2
  2. B
    6 m/s2
  3. C
    9 m/s2
  4. D
    15 m/s2
Question 17Single Answer
The stream function is given by Ψ = 3xy, then the velocity at the point (2,3) is
  1. A
    9
  2. B
    -6
  3. C
    117
  4. D
    10.8
Question 18Single Answer
The boundary layer thickness at a given distance from the leading edge of a flat plate is
  1. A
    More for lighter fluid
  2. B
    More for denser fluid
  3. C
    Less for denser fluid
  4. D
    Less for lighter fluid
Question 19Single Answer
In a laminar flow through a circular pipe, the discharge varies
  1. A
    Linearly with fluid density
  2. B
    Inversely with pressure drop
  3. C
    Directly as square of pipe radius
  4. D
    Inversely with fluid velocity
Question 20Single Answer
A fluid is flowing over a flat plate. At distance of 8 cm from the leading edge, the Reynolds number is found to be 25600. The thickness of the boundary layer at this point is
  1. A
    1.5mm
  2. B
    2.5mm
  3. C
    4.0mm
  4. D
    5.0mm
Question 21Single Answer
If a submerged body displaced from its equilibrium position, returns to its original position, it is called __________.
  1. A
    thermal equilibrium
  2. B
    neutral equilibrium
  3. C
    unstable equilibrium
  4. D
    stable equilibrium
Question 22Single Answer
In a flow measurement, a venturi meter is preferred over an orifice plate because _____.
  1. A
    energy of head loss is less
  2. B
    It is cheaper
  3. C
    pressure drop is more
  4. D
    space is limited  
Question 23Single Answer
Pitot tube measures ______.
  1. A
    dynamic pressure of a moving stream
  2. B
    guage pressure
  3. C
    temperature of moving water
  4. D
    pressure difference between two fluids
Question 24Single Answer
Which of the following is not a property of an ideal fluid ?
  1. A
    flow is irrotational
  2. B
    it has no viscosity
  3. C
    it has viscosity
  4. D
    it is incompressible
Question 25Single Answer
Nozzle used in steam turbines convert ________.
  1. A
    enthalpy of steam into work
  2. B
    enthalpy of steam into kinetic energy
  3. C
    enthalpy of steam into pressure energy
  4. D
    pressure energy into work
Question 26Single Answer
Which of the following assumptions is the most relevant in air-standard cycle analysis ?
  1. A
    All the processes within the cycle are irreversible
  2. B
    Working fluid is a fixed mass
  3. C
    Specific heat of air changes during the cycle
  4. D
    Cycle is assumed to be an open cycle
Question 27Single Answer
The modern Francis turbine is a ___________flow turbine .
  1. A
    tangential 
  2. B
    axial
  3. C
    radial
  4. D
    mixed
Question 28Single Answer
Variation of stress with strain rate for a Newtonian fluid is ______ .
  1. A
    hyperbolic
  2. B
    linear
  3. C
    elliptical
  4. D
    parabolic
Question 29Single Answer
Which of the following is NOT a part of refrigeration systems ?
  1. A
    Turbine
  2. B
    Evaporator
  3. C
    Compressor
  4. D
    Condenser
Question 30Single Answer
Which of the following is NOT an intensive property ?
  1. A
    Temperature
  2. B
    Total volume
  3. C
    Pressure
  4. D
    Density
Question 31Single Answer
What is the state of a substance at the critical point on a phase diagram?
  1. A
    Solid
  2. B
    Liquid
  3. C
    Gas
  4. D
    Indistinguishable liquid-vapor phase
Question 32Single Answer
What does the triple point on a phase diagram represent?
  1. A
    Only solid exists
  2. B
    Solid, liquid, and vapor coexist
  3. C
    Only liquid exists
  4. D
    Only vapor exists
Question 33Single Answer
Which property is constant during a phase change at constant pressure?
  1. A
    Temperature
  2. B
    Volume
  3. C
    Entropy
  4. D
    Internal energy
Question 34Single Answer
What is the quality of a saturated liquid-vapor mixture defined as?
  1. A
    Ratio of liquid mass to total mass
  2. B
    Ratio of vapor mass to total mass
  3. C
    Ratio of liquid volume to total volume
  4. D
    Ratio of vapor volume to total volume
Question 35Single Answer
What is the specific volume of a substance in the saturated liquid state?
  1. A
    vf
  2. B
    vg
  3. C
    vfg
  4. D
    vavg
Question 36Single Answer
Which chart is used to represent the properties of a superheated vapor?
  1. A
    T-s diagram
  2. B
    P-v diagram
  3. C
    Mollier diagram
  4. D
    Psychrometric chart
Question 37Single Answer
What happens to the pressure of a substance at the triple point of water?
  1. A
    It is zero
  2. B
    It is kPa
  3. C
    Resolver 
  4. D
    It is infinite
Question 38Single Answer
What is the slope of the sublimation curve on a P-T diagram?
  1. A
    Zero
  2. B
    Negative
  3. C
    Positive
  4. D
    Infinite
Question 39Single Answer
Which property is used to determine the state of a substance in a compressed liquid region?
  1. A
    Entropy
  2. B
    Specific volume
  3. C
    Quality
  4. D
    Enthalpy
Question 40Single Answer
Which diagram shows constant pressure lines as horizontal?
  1. A
    P-v diagram
  2. B
    T-s diagram
  3. C
    h-s diagram
  4. D
    P-T diagram
Question 41Single Answer
The moment of a force about a point is equal to:
  1. A
    Force × Time
  2. B
    Force × Distance from point
  3. C
    Force × Area
  4. D
    Force ÷ Distance
Question 42Single Answer
Which of the following statements is true?
  1. A
    A particle has mass but no dimensions.
  2. B
    A rigid body can deform under load.
  3. C
    A force cannot be represented by a vector.
  4. D
    Varignon’s theorem applies only to particles.
Question 43Single Answer
Varignon’s theorem states that the moment of a force about any point is equal to:
  1. A
    The algebraic sum of the moments of the components
  2. B
    Twice the product of the force and distance
  3. C
    Half the sum of the components
  4. D
    Product of mass and acceleration
Question 44Single Answer
A rigid body is in equilibrium when:
  1. A
    Net force
  2. B
    Net moment
  3. C
    Net force and net moment
  4. D
    Either net force or net moment
Question 45Single Answer
Which of the following is not a type of force system?
  1. A
    Concurrent
  2. B
    Parallel
  3. C
    Non-concurrent
  4. D
    Perpendicular
Question 46Single Answer
The unit of moment is:
  1. A
    N
  2. B
    N/m
  3. C
    N•m
  4. D
    m/N
Question 47Single Answer
In a force diagram, the direction of a force is represented by:
  1. A
    Length of the arrow
  2. B
    Angle of the arrow
  3. C
    Thickness of the arrow
  4. D
    Color of the arrow
Question 48Single Answer
A free body diagram shows:
  1. A
    Internal forces
  2. B
    Only horizontal forces
  3. C
    All external forces acting on a body
  4. D
    Only vertical forces
Question 49Single Answer
The resultant of two equal forces acting at right angles is:
  1. A
    Equal to one of the forces
  2. B
    times one force
  3. C
    Twice one force
  4. D
    Zero
Question 50Single Answer
The force which keeps a body in equilibrium is:
  1. A
    Resultant
  2. B
    Balanced force
  3. C
    Equilibrant
  4. D
    Reaction
Important Questions Package

SAMEER Project Engineer Exam Online Question Bank Package

Buy SAMEER Project Engineer Important Questions, MCQ, question answer in Hindi & English. It will help you to score high marks in SAMEER Project Engineer question bank 2026 in Online, PDF & Print study material.

+ Free Monthly Current Affairs, GK & more PDF Download
Sr.Package NameAmount
1.SAMEER Project Engineer Exam (Electronics Engineering) - English
Description : 1000 Question with Answer
₹101 [₹500]
2.SAMEER Project Engineer Exam (Electronics Engineering) - English
Description : 2000 Question with Answer
₹151 [₹500]
3.SAMEER Project Engineer Exam (Electronics Engineering) - English
Description : 3000 Question with Answer
₹181 [₹500]
4.SAMEER Project Engineer Exam (Electronics Engineering) - English
Description : 4000 Question with Answer
₹201 [₹500]
5.SAMEER Project Engineer Exam (Mechanical Engineering) - English
Description : 1000 Question with Answer
₹101 [₹500]
6.SAMEER Project Engineer Exam (Mechanical Engineering) - English
Description : 2000 Question with Answer
₹151 [₹500]
7.SAMEER Project Engineer Exam (Mechanical Engineering) - English
Description : 3000 Question with Answer
₹181 [₹500]
8.SAMEER Project Engineer Exam (Mechanical Engineering) - English
Description : 4000 Question with Answer
₹201 [₹500]
9.SAMEER Project Engineer Exam (Electronics Engineering) - English
Description : 1000 Question & Answer Download in PDF (Send by Email)
₹151 [₹550]
10.SAMEER Project Engineer Exam (Mechanical Engineering) - English
Description : 1000 Question & Answer Download in PDF (Send by Email)
₹151 [₹450]
11.SAMEER Project Engineer Exam (Electronics Engineering) Question Bank Book - English
Description : 1000 Question with Answer (Printed Material)
₹390 [₹600]
12.SAMEER Project Engineer Exam (Mechanical Engineering) Question Bank Book - English
Description : 1000 Question with Answer (Printed Material)
₹390 [₹600]
13.SAMEER Project Engineer Exam (Electronics Engineering) - English (Old)
Description : 1000 Question With Answer
₹101 [₹500]
Back to Exam