📚 Exam by Category
▾
Objective Questions

Latest PUNEZP Health Worker Exam Question (Objective Questions), MCQ in English

Subjects : Electrical, Civil, Mechanical

Question Bank PUNEZP Health Worker Exam - English
Back to Exam

Electrical

Question 1Single Answer
Assuming both the voltage sources are in phase, the value of R for which maximum power is transferred from circuit A to circuit B is
  1. A
    0.8 Ω
  2. B
    1.4 Ω
  3. C
    2 Ω
  4. D
    2.8 Ω
Question 2Single Answer
For the intrinsic gallium-arsenide, the conductivity at room temperature 25°C is 10-6 (ohm-m)-1, the electron and hole nobilities are 0.85 m2/V-s and 0.04 m2/V-s respectively. What is the intrinsic carrier concentration at the room temperature?
  1. A
    7.0 × 1012 m-3
  2. B
    7.0 × 10-12 m-3
  3. C
    7.0 × 10-12 m3
  4. D
    7.0 × 1012 m3
Question 3Single Answer
The resistivity of intrinsic germanium at 30°C is 0.46 –m. What is the intrinsic carrier density at 30°C if the electron mobility is 0.38 m2/V-s and the hole mobility is 0.18 m2/V-s?
  1. A
    9.2 × 105/m3
  2. B
    2.77 × 103/m3
  3. C
    2.43 × 1019/m3
  4. D
    8.9 × 1012/m3
Question 4Single Answer
Heat conduction in a semiconductor takes place
  1. A
    By the mobility of the carriers
  2. B
    Due to energy gap between conduction band and valency band
  3. C
    By the holes and thermal vibrations of atoms
  4. D
    By the electrons and thermal vibrations of atoms
Question 5Single Answer
Brewster angle is the angle when a wave is incident on the surface of a perfect dielectric at which there is no reflected wave and the incident wave is
  1. A
    Parallel polarized
  2. B
    Perpendicularly polarized
  3. C
    Normally polarized
  4. D
    None of the above
Question 6Single Answer
An electrical breakdown of a p-n junction occurs if
  1. A
    Forward voltage increases up to the rating
  2. B
    Reverse voltage increases beyond the rating
  3. C
    Forward voltage decreases below the rating
  4. D
    Reverse voltage decreases below the rating
Question 7Single Answer
The chief deterrent to the widespread application of superconducting materials is
  1. A
    Very difficult to form, machine or case
  2. B
    The difficult in attaining and maintaining extremely low temperature
  3. C
    The poor strength-to-weight ratio
  4. D
    The lower oxidation rate at elevated temperatures
Question 8Single Answer
Which one of the following properties is not observed in the carbon nanotubes ?
  1. A
    High stiffness and strengths
  2. B
    Low densities
  3. C
    Unusual electrical property
  4. D
    Non-ductile
Question 9Single Answer
The evidence for the importance of electron-phonon interaction in super-conductors comes from
  1. A
    Meissner effect
  2. B
    Josephson effect
  3. C
    Isotope effect
  4. D
    x quantization experiments
Question 10Single Answer
Which one of the following materials is used for cable insulation ?
  1. A
    Phenol formaldehyde
  2. B
    Polytetrafluoroethylene
  3. C
    Polyvinyl chloride
  4. D
    Acrylonitrile butadiene styrene
Question 11Single Answer
For high speed reading and storing of information in a computer, the material used is
  1. A
    Ferrite
  2. B
    Piezoelectric
  3. C
    Pyroelectric
  4. D
    Ferromagnetic above 768°C
Question 12Single Answer
The temperature above which an anti-ferromagnetic material becomes paramagnetic is called
  1. A
    Peak temperature
  2. B
    Neel temperatur
  3. C
    Critical temperature
  4. D
    Weiss temperature
Question 13Single Answer
Which effect is the converse of Peltier effect ?
  1. A
    Seeback effect
  2. B
    Thomson effect
  3. C
    Hall effect
  4. D
    Joule effect
Question 14Single Answer
Magnetic materials which may be readily magnetized in either direction are
  1. A
    Soft magnetic materials
  2. B
    Hard magnetic materials
  3. C
    High eddy current loss materials
  4. D
    High hysteresis loss materials
Question 15Single Answer
Consider the following statements regarding a ferromagnetic material:
1.Below the ferromagnetic Curie temperature, the ferromagnetic materials exhibit hysteresis effect.
2.The coercive force is the filed required to reduce the flux density to zero. 
Which of the above statements is/are correct?
  1. A
    Both 1 and 2
  2. B
    Neither 1 nor 2
  3. C
    1 only
  4. D
    2 only
Question 16Single Answer
The impact ionization phenomenon in semiconductor may be viewed as the reverse process of
  1. A
    Radiative recombination
  2. B
    Auger recombination
  3. C
    Surface recombination
  4. D
    Shockley-Read-Hall recombination
Question 17Single Answer
Refractive index of a slice glass can be reduced by doping it with tiny amount of
  1. A
    GeO2
  2. B
    B2O3
  3. C
    P2O5x
  4. D
    Al2O3
Question 18Single Answer
If a diameter of a copper wire is increased by two times keeping its terminal voltage same, then the drift velocity will
  1. A
    Become twice
  2. B
    Become half
  3. C
    ecome four times
  4. D
    Remain unchanged
Question 19Single Answer
In an induction type energy meter, the steady speed attained by the rotating disc is
1.Proportional to the deflecting torque.
2.Proportional to the resistance of the path of eddy currents.
3.Inversely proportional to the effective readings of disc from its axis.
4.Inversely proportional to the square of brake magnetic flux. 
Which of the above are correct?
  1. A
    1, 2 and 3 only
  2. B
    1, 2 and 4 only
  3. C
    2, 3 and 4 only
  4. D
    1, 2, 3 and 4
Question 20Single Answer
If ‘KCLFTSB’ stands for ‘best of  luck’ and ‘SHSWDG’ stands for ‘good wishes’, which of the following indicates ‘ace the exam’?
  1. A
    MCHTX
  2. B
    MXHTC
  3. C
    XMHCT
  4. D
    XMHTC
Question 21Single Answer
Consider  the following statements associated with the basic electrostatic properties of ideal conductors:
1.The resultant field inside is zero.
2.The net charge density in the interior is zero.
3.Any net charges reside on the surface.
4.The surface is always equipotential.
5.The field just outside is zero. 
Which of the above statements are correct?
  1. A
    1, 2, 3 and 4
  2. B
    3, 4 and 5 only
  3. C
    1, 2 and 3 only
  4. D
    2 and 3 only
Question 22Single Answer
A semiconductor device made out of a material having very high temperature coefficient of resistance is
  1. A
    Transistor
  2. B
    Varistor
  3. C
    Thyristor
  4. D
    Thermistor
Question 23Single Answer
The electrical conductivity of a semiconductor increases with increase in temperature because
  1. A
    The carrier concentration increases
  2. B
    The mobility of carrier increases
  3. C
    Both carrier concentration and mobility increases
  4. D
    The band gap decreases
Question 24Single Answer
Which of the following are associated with soft superconductors?
1.Silsbee’s rule
2.Meissner effect
3.Faraday rotation
4.Curie-Weiss law
  1. A
    2, 3 and 4
  2. B
    1 and 3 only
  3. C
    1 and 2 only
  4. D
    2 and 3 only
Question 25Single Answer
In a two-channel oscilloscope operating in x-y mode, two in-phase 50 Hz sinusoidal waveforms of equal amplitude are fed to the two channels. What will be the resultant pattern on the screen?
  1. A
    An ellipse
  2. B
    A parabola
  3. C
    Straight line inclined at 45 with respect to x-axis
  4. D
    A circle
Question 26Single Answer
Materials, whose resistivity at very low temperature plunges from a finite value to zero and remains there upon further cooling, are known as
  1. A
    Ferromagnetic materials
  2. B
    High-energy hard magnetic materials
  3. C
    Superconductors
  4. D
    Ferromagnetic materials
Question 27Single Answer
In a superconductor, is the temperature is decreased below its critical temperature, the value of critical magnetic field will
  1. A
    Increase
  2. B
    Decrease
  3. C
    Not change
  4. D
    Increase or decrease depending on the superconductor material
Question 28Single Answer
The imaginary part of dielectric constant determines
  1. A
    Component of current which is in phase with the applied field
  2. B
    Component of energy absorbed per m3
  3. C
    Amount of applied field
  4. D
    Component of voltage which is in phase with the applied field
Question 29Single Answer
Direction: Each of the items consists of two statements, one labeled as the ‘Statement (I)’ and the other as ‘Statement (II)’. Examine these two statements carefully and select the answers to these items using the codes given below
  1. A
    Statement (I):Hard magnetic materials are used for making permanent magnets.
    Statement (II):
    Hard magnetic materials have relatively small and narrow hysteresis loop.
  2. B
    Both Statement (I) and Statement (II) are individually true and Statement (II) is the correct explanation of Statement (I)
  3. C
    Both Statement (I) and Statement (II) are individually true and Statement (II) is NOT the correct explanation of Statement (I)
  4. D
    Statement (I) is true but Statement (II) is false
  5. E
    Statement (I) is false but Statement (II) is true 
Question 30Single Answer
In 8085A microprocessor, the operation performed by the instruction LHLD 2100 H is                                    
  1. A
    (H) ← 21 H, (L) ←00 
  2. B
    (H) ← M (2100 H), (L) ←M(2101H)
  3. C
    (H) ← M (2100 H), (L) ←M(2100H)
  4. D
    (H) ← 00H, (L) ←21H                                                 

Civil

Question 31Single Answer
Consider the following statements :
1. There will be no defects in select grade timbers.
2. The codal values for strength of grade-II timer without defects may be reduced by 37.5%.
3. For timber used as columns, the permissible stress in ungraded timbers is adopted with a multiplying factor of 0.50.
4. In case of wind force and earthquakes, a modification factor of 1.33 is adopted. Which of the above statements are correct ? 
  1. A
    1 and 3 only
  2. B
    1 and 4 only
  3. C
    2 and 4 only
  4. D
    2 and 3 only
Question 32Single Answer
Consider the following statements regarding timber :
1. The strength of timber increases by Kiln seasoning.
 2. Cutting of wood is to be done prior to treatment.
3. Water seasoning is good for prevention of warping.
4. ASCU treatment enhances the strength of wood. Which of the above statements are correct ?
  1. A
    1, 2 and 3 only
  2. B
    2, 3 and 4 only
  3. C
    1, 3 and 4 only
  4. D
    1, 2, 3 and 4
Question 33Single Answer
Gase(s) emitted during rotting or decomposition of timber is /are mainly
  1. A
    Methane and Hydrogen
  2. B
    Hydrogen Sulphide
  3. C
    Carbonic acid and Hydrogen
  4. D
    Ammonia
Question 34Single Answer
Efflorescence of bricks is due to
  1. A
    Excessive burning of bricks
  2. B
    High silt content in brick clay
  3. C
    High porosity of bricks
  4. D
    Soluble salts present in parent clay
Question 35Single Answer
Disintegration of bricks masonry walls is primarily due to
1. Efflorescence
2. Magnesium sulphate in brick  
3. Calcined clay admixtures
4. Kankar nodules
Which of the a above statements are correct ? 
  1. A
    1, 2 and 3 only
  2. B
    1, 2 and 4 only
  3. C
    3 and 4 only
  4. D
    1, 2, 3 and 4
Question 36Single Answer
Consider the following test :
1. Transverse strength test
2. Water absorption test
3. Impact test
4. Breaking strength test
Which of the above are relevant to testing of tiles ?
  1. A
    1, 2 and 3 only
  2. B
    1, 2 and 4 only
  3. C
    3 and 4 only
  4. D
    1, 2, 3 and 4
Question 37Single Answer
Which of the following statements is/are correct regarding the strength of cement ?
1. Particle sizes less than 3 m increases the viscous nature of the cement.
2. Finer particles in cement can be replaced by fly-ash to improve the strength.
  1. A
    1 only
  2. B
    2 only
  3. C
    Both 1 and 2
  4. D
    Neither 1 nor 2
Question 38Single Answer
The constituent compound in Portland cement which reacts immediately with water, and also sets earliest, is
  1. A
    Tricalcium silicate
  2. B
    Dicalcium silicate
  3. C
    Tricalcium aluminate
  4. D
    Tetracalcium aluminoferrite
Question 39Single Answer
Which of the following statements are correct with regard to cement mortar ?
1. Workability of cement mortar can be improved by addition of lime.
2. Fly-ash cement is economical in plastering jobs.
3. Addition of saw dust improves workability.
4. Sand in mortar can be replaced by finely crushed fire bricks.
  1. A
    1, 2, 3 and 4
  2. B
    1, 2 and 3 only
  3. C
    3 and 4 only
  4. D
    1, 2 and 4 only
Question 40Single Answer
In a concrete mix of proportion 1 : 3 : 6, the actual quantity of sand, which is judged to have undergone 15% bulking, per unit volume of cement, will be
  1. A
    3.00
  2. B
    3.45
  3. C
    4.50
  4. D
    6.00
Question 41Single Answer
Which method of curing of concrete is recommendable for rapid gain of strength of concrete ?
  1. A
    Sprinkling water
  2. B
    Membrane curing
  3. C
    High-pressure steam curing
  4. D
    Infrared radiation curing
Question 42Single Answer
Which of the following is appropriate as  simple field method for assesing consistency of concrete ?
  1. A
    Compacting factor
  2. B
    Slump test
  3. C
    Vee-Bee test
  4. D
    Kelly Ball test
Question 43Single Answer
Which of the following are relatable to Autoclaved Aerated Concrete ?
1. Light weight
2. Strong
3 Inorganic
4. Nontoxic
  1. A
    1, 2 and 3 only
  2. B
    1, 2 and 4 only
  3. C
    3 and 4 only
  4. D
    1, 2, 3 and 4
Question 44Single Answer
The workability of concrete becomes more reliable depending on
1. Aggregate-cement ratio
2. Time of transit
3. Grading of the aggregate
  1. A
    1 only
  2. B
    2 only
  3. C
    3 only
  4. D
    1, 2 and 3
Question 45Single Answer
Which of the following statements are correct for stresses acting on mutually perpendicular faces of a plane element ?
1. The sum of the normal stresses in mutually perpendicular planes is equal to the sum of the principal stresses.
2. The shearing stresses in two mutually perpendicular planes are equal in magnitude and direction.
3. Maximum shear stress is half of the difference between principal stresses.
  1. A
    1, 2 and 3 only
  2. B
    1 and 2 only
  3. C
    2 and 3 only
  4. D
    1 and 3 only
Question 46Single Answer
Which of the following statements are correct?
1. Strain in the direction of applied stress is known as longitudinal strain.
2. Tensile stress results in tensile strain in linear and lateral directions.
3. Strains in all directions perpendicular to the applied stress are known as lateral strain. 4. Ratio of change in volume to original volume is known as volumetric strain.
  1. A
    1, 2 and 3 only
  2. B
    1, 3 and 4 only
  3. C
    3 and 4 only
  4. D
    1, 2, 3 and 4
Question 47Single Answer
In the cross-section of a timber, cambium layer can occur in
  1. A
    Inner Bark and Sap Wood
  2. B
    Pith and Heart Wood
  3. C
    Sap Wood and Heart Wood
  4. D
    Outer Bark and Sap Wood
Question 48Single Answer
Consider the following statements :
1. In the infinitesimal strain theory, dilatation is taken as an invariant.
2. Dilatation is not proportional to the algebraic sum of all normal stresses.
3. The shearing modulus is always less than the elastic modulus.
Which of the above statements is/are correct ?
  1. A
    1 only
  2. B
    1 and 2 only
  3. C
    2 only
  4. D
    1, 2 and 3
Question 49Single Answer
Which one of the following represents constitutive relationship ?
  1. A
    Vertical displacements in a structure
  2. B
    Rotational displacements in a structure
  3. C
    System of forces in equilibrium
  4. D
    Stress-strain behavior of a material
Question 50Single Answer
Principal stresses at a point are 80 N/mm2 and 40 N/mm2, both tensile. The yield stress in simple tension for this material is 200 N/mm2. The values of factors of safety according to maximum principal stress theory and maximum shear stress theory, respectively, are
  1. A
    2.5 and 2.5
  2. B
    2.5 and 5
  3. C
    5 and 1.67
  4. D
    6 and 2.50
Important Questions Package

PUNEZP Health Worker Exam Online Question Bank Package

Buy PUNEZP Health Worker Important Questions, MCQ, question answer in Hindi & English. It will help you to score high marks in PUNEZP Health Worker question bank 2026 in Online, PDF & Print study material.

+ Free Monthly Current Affairs, GK & more PDF Download
Sr.Package NameAmount
1.PUNEZP Health Worker Exam - English
Description : 2320 Question With Answer
₹181 [₹500]
2.PUNEZP Health Worker Exam - Hindi
Description : 2220 Question With Answer
₹181 [₹500]
3.PUNEZP Health Worker Exam Question Bank Book - English
Description : 1000 Question with Answer (Printed Material)
₹390 [₹600]
4.PUNEZP Health Worker Exam Question Bank Book - Hindi
Description : 1000 Question with Answer (Printed Material)
₹450 [₹800]
Back to Exam