Which method determines sulfate by weighing BaSO₄?
A
Potentiometry
B
Precipitation gravimetry
C
Flame photometry
D
Complexometric titration
Question 2Single Answer
Which method is classified as instrumental analysis?
A
Acid–base titration with a visual indicator
B
Gravimetric chloride determination
C
Atomic absorption spectrometry
D
Iodometric titration with starch
Question 3Single Answer
In volumetric titrimetry, which quantity is measured directly from the burette?
A
Titrant concentration
B
Moles of analyte
C
Mass of solute
D
Volume of titrant delivered
Question 4Single Answer
At a titration’s equivalence point, what condition is met?
A
Titrant and analyte have reacted in stoichiometric amounts
B
The indicator has just changed colour
C
The solution always has pH 7
D
The titrant and analyte volumes are equal
Question 5Single Answer
An endpoint occurs at 25.20 mL and equivalence at 25.00 mL. What is the signed endpoint error?
A
−0.20 mL
B
+0.80 mL
C
+0.20 mL
D
−0.80 mL
Question 6Single Answer
What molarity of HCl is neutralized when 25.0 mL requires 15.0 mL of 0.200 M NaOH?
A
0.0750 M
B
0.200 M
C
0.120 M
D
0.333 M
Question 7Single Answer
Which primary standard is commonly used to standardize aqueous NaOH?
A
Sodium chloride
B
Potassium hydrogen phthalate
C
Potassium nitrate
D
Calcium chloride
Question 8Single Answer
Why is solid NaOH unsuitable as a primary standard?
A
It has a very low molar mass
B
It reacts with water to form an insoluble product
C
It does not dissociate in water
D
It absorbs moisture and carbon dioxide from air
Question 9Single Answer
Which approach suits a solid that reacts slowly with a measured excess of standard acid?
A
Direct titration with the same acid
B
Indicator-free dilution
C
Back titration of the remaining acid
D
Blank titration without the solid
Question 10Single Answer
A CaCO₃ sample consumes 6.00 mmol of HCl. How much CaCO₃ reacts?
A
3.00 mmol
B
6.00 mmol
C
12.00 mmol
D
1.50 mmol
Question 11Single Answer
What is the mole ratio of EDTA to Ca²⁺ in a hardness titration?
A
1:1
B
1:2
C
2:1
D
2:3
Question 12Single Answer
Which solid gives the brick-red endpoint in a Mohr titration?
A
AgCl
B
AgSCN
C
Ag₂CrO₄
D
AgBr
Question 13Single Answer
In the Fajans method, what causes the indicator’s endpoint colour change?
A
Oxidation of the indicator by nitrate
B
Sublimation of the indicator
C
Hydrolysis of the indicator in bulk solution
D
Adsorption of the indicator onto the precipitate
Question 14Single Answer
One mole of iodine reacts with how many moles of thiosulfate in iodometry?
A
½ mol
B
1 mol
C
4 mol
D
2 mol
Question 15Single Answer
In acidic medium, one mole of permanganate oxidizes how many moles of Fe²⁺?
A
3 mol
B
2 mol
C
5 mol
D
1 mol
Question 16Single Answer
Which property is desirable in the final weighed form of a gravimetric analyte?
A
Rapid moisture uptake
B
Variable hydration
C
High volatility
D
Definite chemical composition
Question 17Single Answer
Which change generally favours larger crystals during precipitation?
A
Lowering relative supersaturation
B
Increasing relative supersaturation
C
Adding precipitant rapidly without mixing
D
Increasing the nucleation rate
Question 18Single Answer
What happens to fine particles during normal digestion of a precipitate?
A
They all become more soluble than before
B
Smaller particles dissolve and material deposits on larger ones
C
They become charged by ignition
D
They are converted into an unrelated compound
Question 19Single Answer
Mother liquor becomes trapped inside a growing crystal. What is this impurity mechanism?
A
Surface desorption
B
Peptization
C
Sublimation
D
Occlusion
Question 20Single Answer
Why may a suitable volatile electrolyte be added to a precipitate wash liquid?
A
It increases the precipitate’s solubility
B
It helps prevent peptization
C
It changes the analyte’s oxidation state
D
It increases the final mass permanently
Question 21Single Answer
A sample yields 0.287 g of AgCl. Using molar masses of 143.3 g mol⁻¹ for AgCl and 35.45 g mol⁻¹ for Cl, what mass of chloride was present?
A
0.0710 g
B
0.0355 g
C
0.142 g
D
0.216 g
Question 22Single Answer
Where should an ignited crucible cool before weighing?
A
In a desiccator
B
Under running water
C
On an exposed bench beside a sink
D
In a steam chamber
Question 23Single Answer
A gravimetric product is weighed while still damp. How is the calculated analyte content affected?
A
It is unaffected
B
It is biased low
C
It is biased high
D
Its precision always improves
Question 24Single Answer
Which method is most suitable for determining trace Pb in a dilute water sample?
A
Visual acid–base titration
B
Graphite furnace atomic absorption spectrometry
C
Pycnometry
D
Capillary viscometry
Question 25Single Answer
A sample exceeds the upper limit of a validated linear calibration. What is the best next step?
A
Extrapolate the calibration
B
Report the upper calibration limit as the result
C
Dilute appropriately and remeasure
D
Force the calibration intercept to zero
Question 26Single Answer
A result is above the detection limit but below the quantification limit. What can be concluded?
A
The analyte is absent
B
The concentration can be reported at full validated precision
C
The analyte is detected below the validated quantification limit
D
The instrument is saturated
Question 27Single Answer
Which property describes a method’s ability to distinguish an analyte from interferents?
A
Selectivity
B
Repeatability
C
Sensitivity
D
Linearity
Question 28Single Answer
A method gives 9.79, 9.80 and 9.81 mg L⁻¹ for a 10.00 mg L⁻¹ standard. What pattern is evident?
A
Good precision and negative bias
B
Good precision and positive bias
C
Poor precision and positive bias
D
Poor precision and no bias
Question 29Single Answer
A balance consistently reads 0.005 g high. Which error does this illustrate?
A
Random error
B
Systematic error
C
Sampling variance
D
Rounding error
Question 30Single Answer
A reference value of 80.0 mg is measured as 78.0 mg. What is the signed relative error?
A
−2.50%
B
−2.00%
C
+2.00%
D
+2.50%
Question 31Single Answer
Which control checks for contamination introduced during digestion?
A
A method blank taken through digestion
B
A second reading of the sample digest
C
An instrument standard prepared after digestion
D
An undigested duplicate sample
Question 32Single Answer
A 4.0 mg L⁻¹ spike increases the measured concentration from 7.0 to 10.6 mg L⁻¹. What is the recovery after dilution correction?
A
85%
B
95%
C
90%
D
110%
Question 33Single Answer
Which calibration approach compensates for constant proportional matrix suppression in a linear response range?
A
Calibration with pure solvent alone
B
Standard additions
C
Blank subtraction alone
D
Repeated readings of the unspiked sample
Question 34Single Answer
Which procedure gives a representative subsample of a heterogeneous crushed solid?
A
Selecting only the largest particles
B
Taking material from the container surface
C
Mixing thoroughly and using a riffle splitter
D
Removing all fine particles
Question 35Single Answer
Which preparation minimizes loss of volatile analytes during digestion?
A
Open dry ashing
B
Closed-vessel digestion
C
Prolonged boiling in an open beaker
D
Evaporation to dryness
Question 36Single Answer
In solid-phase extraction, which step removes a retained analyte from the sorbent?
A
Conditioning
B
Elution
C
Sample loading
D
Cartridge equilibration
Question 37Single Answer
What stock volume is needed to prepare 100.0 mL of 0.0250 M solution from 0.500 M stock?
A
2.50 mL
B
12.50 mL
C
5.00 mL
D
20.00 mL
Question 38Single Answer
How should concentrated sulfuric acid be diluted with water?
A
Add the acid slowly to water while stirring and cooling as needed
B
Mix both liquids in a sealed flask
C
Add the acid to boiling water
D
Add water rapidly to the acid
Question 39Single Answer
Which equipment controls inhalation exposure while dispensing a volatile reagent?
A
Desiccator
B
Laminar-flow clean bench
C
Chemical fume hood
D
Open bench with a fan
Question 40Single Answer
A 25.00 mL pycnometer holds 22.50 g of liquid. What is the density?
A
0.9000 g mL⁻¹
B
1.111 g mL⁻¹
C
0.8000 g mL⁻¹
D
1.125 g mL⁻¹
Question 41Single Answer
Which instrument determines density from the oscillation period of a filled tube?
A
Ostwald viscometer
B
Nephelometer
C
Abbe refractometer
D
Oscillating U-tube densimeter
Question 42Single Answer
In one capillary viscometer, X has twice the flow time and 0.90 times the density of Y. What is the dynamic viscosity ratio X:Y?
A
1.80
B
0.90
C
2.22
D
0.45
Question 43Single Answer
A liquid has a viscosity of 3.00 mPa·s and a density of 1.50 g cm⁻³. What is its kinematic viscosity?
A
0.500 mm² s⁻¹
B
2.00 mm² s⁻¹
C
4.50 mm² s⁻¹
D
200 mm² s⁻¹
Question 44Single Answer
At fixed temperature, which property remains constant with shear rate for a Newtonian liquid?
A
Shear stress
B
Dynamic viscosity
C
Flow velocity
D
Pressure drop
Question 45Single Answer
In the Stokes regime, the same sphere falls in two liquids of equal density. Which liquid is more viscous?
A
The one with the higher terminal speed
B
Both have equal viscosity because their densities match
C
The one in the taller cylinder, regardless of speed
D
The one with the lower terminal speed
Question 46Single Answer
Which laboratory variable is nominal?
A
Sample temperature
B
Reagent manufacturer
C
Number of defects
D
Severity rating
Question 47Single Answer
A sample is rated poor, fair or good. What type of data is recorded?
A
Ordinal
B
Nominal
C
Continuous ratio
D
Continuous interval
Question 48Single Answer
Which variable is discrete quantitative?
A
Sample volume
B
Number of failed blanks
C
Reagent identity
D
Solution temperature
Question 49Single Answer
Which measurement uses an interval scale?
A
Mass in grams
B
Volume in millilitres
C
Time in seconds
D
Temperature in degrees Celsius
Question 50Single Answer
What is the mean of 6, 8, 9, 11 and 16?
A
10
B
11
C
12
D
9
Important Questions Package
OPSC Scientific Officer Chemistry Exam Online Question Bank Package
Buy OPSC Scientific Officer Chemistry Important Questions, MCQ, question answer in Hindi & English. It will help you to score high marks in OPSC Scientific Officer Chemistry question bank 2026 in Online, PDF & Print study material.
+ Free Monthly Current Affairs, GK & more PDF Download
Sr.
Package Name
Amount
1.
OPSC Scientific Officer (Chemistry) Paper I Exam - English
Description : 1000 Questions with Answers
₹101[₹500]
2.
OPSC Scientific Officer (Chemistry) Paper I Exam - English
Description : 2000 Questions with Answers
₹151[₹500]
3.
OPSC Scientific Officer (Chemistry) Paper I Exam - English
Description : 3000 Questions with Answers
₹181[₹500]
4.
OPSC Scientific Officer (Chemistry) Paper I Exam - English
Description : 4000 Questions with Answers
₹201[₹500]
5.
OPSC Scientific Officer (Chemistry) Paper I Exam - English
Description : 5000 Questions with Answers
₹221[₹500]
6.
OPSC Scientific Officer (Chemistry) Paper I Exam - English
Description : 1000 Question & Answer Download in PDF (Send by Email)
₹151[₹450]
7.
OPSC Scientific Officer (Chemistry) Paper I Exam Question Bank Book - English
Description : 1000 Question with Answer (Printed Material)
₹390[₹600]
8.
OPSC Scientific Officer (Chemistry) Paper II Exam - English
Description : 1000 Question with Answer
₹101[₹500]
9.
OPSC Scientific Officer (Chemistry) Paper II Exam - English
Description : 2000 Question with Answer
₹151[₹500]
10.
OPSC Scientific Officer (Chemistry) Paper II Exam - English
Description : 3000 Question with Answer
₹181[₹500]
Concerned Subject (Chemistry)
Question 51Single Answer
What is the median of 3, 5, 8, 12, 19 and 24?
A
11
B
8
C
10
D
12
Question 52Single Answer
Which dataset has two modes?
A
1, 1, 2, 3, 3
B
2, 2, 2, 3, 4
C
1, 2, 3, 4, 5
D
4, 5, 5, 6, 7
Question 53Single Answer
Which measure of centre is least affected by one extremely high reading?
A
Median
B
Arithmetic mean
C
Midrange
D
Root mean square
Question 54Single Answer
Five readings average 12 mg L⁻¹ and 15 readings average 16 mg L⁻¹. What is the combined mean?
A
15 mg L⁻¹
B
14 mg L⁻¹
C
16 mg L⁻¹
D
13 mg L⁻¹
Question 55Single Answer
What is the range?
A
6.5
B
7.5
C
7.9
D
15.9
Question 56Single Answer
What is the interquartile range?
A
6.5
B
24.5
C
13
D
49
Question 57Single Answer
What is the sample variance of 2, 4 and 6 using the n − 1 denominator?
A
2
B
4
C
8
D
2.67
Question 58Single Answer
A variance is 0.0025 (mg L⁻¹)². What is the standard deviation?
A
0.050 mg L⁻¹
B
0.0050 mg L⁻¹
C
0.025 mg L⁻¹
D
0.0025 mg L⁻¹
Question 59Single Answer
A mean is 25.0 mg L⁻¹ and its standard deviation is 0.50 mg L⁻¹. What is the relative standard deviation?
A
5.0%
B
0.50%
C
2.0%
D
12.5%
Question 60Single Answer
By what factor does the variance change?
A
9
B
3
C
1
D
27
Question 61Single Answer
Every measurement is corrected by subtracting 0.20 mg L⁻¹. What happens to its dataset’s standard deviation?
A
It stays the same
B
It falls by 0.20 mg L⁻¹
C
It rises by 0.20 mg L⁻¹
D
It becomes zero
Question 62Single Answer
Sixteen independent replicates give a standard deviation of 0.24 mg L⁻¹. What is the estimated standard error of their mean?
A
0.015 mg L⁻¹
B
0.12 mg L⁻¹
C
0.060 mg L⁻¹
D
0.24 mg L⁻¹
Question 63Single Answer
What does Pearson’s r = −0.92 indicate?
A
No linear association
B
A weak negative linear association
C
A strong positive linear association
D
A strong negative linear association
Question 64Single Answer
A clear U-shaped scatterplot yields Pearson’s r near zero. Which interpretation fits?
A
The variables are independent
B
Both variables have zero variance
C
A nonlinear association can coexist with little linear correlation
D
The association must be strongly negative
Question 65Single Answer
Which coefficient is Pearson’s correlation calculated on ranks?
A
Spearman’s rank correlation
B
Kendall’s tau
C
Phi coefficient
D
Point-biserial correlation
Question 66Single Answer
What is r after one is multiplied by −1?
A
−0.70
B
−0.49
C
+0.49
D
+0.70
Question 67Single Answer
What is C when A = 0.260?
A
6.00
B
4.80
C
5.20
D
5.00
Question 68Single Answer
What is the observed-minus-fitted residual?
A
+0.014
B
−0.856
C
−0.014
D
+0.856
Question 69Single Answer
What quantity does ordinary least squares minimize?
A
The sum of absolute residuals
B
The sum of squared residuals
C
The largest absolute residual
D
The sum of squared fitted values
Question 70Single Answer
What is R²?
A
−0.64
B
0.80
C
0.40
D
0.64
Question 71Single Answer
A straight-line fit gives positive residuals at both ends and negative ones in the middle. What does this suggest?
A
The model fits perfectly
B
The fitted slope must be zero
C
The residual variance is zero
D
The response has curvature
Question 72Single Answer
A calibration fitted from 1 to 8 mg L⁻¹ is used at 12 mg L⁻¹. What is this called?
A
Interpolation
B
Extrapolation
C
Standard addition
D
Normalization
Question 73Single Answer
What null hypothesis is used in a two-sided test of bias against a certified mean?
A
The population variance is zero
B
The method’s population mean exceeds the certified mean
C
The method’s population mean equals the certified mean
D
Every replicate equals the certified mean
Question 74Single Answer
What is the decision?
A
Reject the null hypothesis
B
Accept the alternative hypothesis
C
Fail to reject the null hypothesis
D
Prove the null hypothesis
Question 75Single Answer
What is a Type I error?
A
Failing to reject a false null hypothesis
B
Rejecting a true null hypothesis
C
Rejecting a false null hypothesis
D
Failing to reject a true null hypothesis
Question 76Single Answer
A test has 90% power against a specified bias. What is its Type II error probability at that bias?
A
5%
B
90%
C
95%
D
10%
Question 77Single Answer
Two methods measure each of the same 12 specimens. Which test compares their mean readings using the matching?
A
Pooled independent-samples t-test
B
Paired t-test
C
Chi-square goodness-of-fit test
D
Chi-square test of independence
Question 78Single Answer
Which t-test compares independent means without assuming equal population variances?
A
Paired t-test
B
Welch’s t-test
C
Pooled two-sample t-test
D
One-sample t-test
Question 79Single Answer
What is the t statistic?
A
−0.50
B
+2.00
C
−2.00
D
+0.50
Question 80Single Answer
A two-sided 95% confidence interval for mean bias is −0.7 to +0.1 mg L⁻¹. What follows at the 5% level?
A
The bias is significantly positive
B
Zero bias cannot be rejected
C
The bias is significantly negative
D
The true bias is exactly zero
Question 81Single Answer
What is Pearson’s chi-square statistic?
A
1.20
B
3.60
C
2.40
D
4.80
Question 82Single Answer
A chi-square test of independence uses a 4 × 5 table. What are its degrees of freedom?
A
7
B
12
C
20
D
8
Question 83Single Answer
A goodness-of-fit test has six categories and estimates two parameters. What are its degrees of freedom?
A
2
B
3
C
4
D
5
Question 84Single Answer
Which population assumption is needed for the usual exact chi-square test of a single variance?
A
Uniformity
B
Binomial sampling
C
Normality
D
Equal category probabilities
Question 85Single Answer
Two independent trials each have a 10% failure probability. What is the probability of at least one failure?
A
19%
B
10%
C
20%
D
1%
Question 86Single Answer
Which operation sends (x, y, z) to (−x, −y, −z)?
A
A C₂ rotation about z
B
Reflection in the xy plane
C
Inversion
D
Reflection in the yz plane
Question 87Single Answer
What is the rotation angle of a single C₅ operation?
A
72°
B
60°
C
36°
D
90°
Question 88Single Answer
Which operations combine to give S₄?
A
A 90° rotation and inversion
B
A 180° rotation and reflection perpendicular to the axis
C
A 90° rotation and reflection perpendicular to the axis
D
A 90° rotation and reflection through a plane containing the axis
Question 89Single Answer
What results from two successive S₄ operations about the same axis?
A
Inversion
B
A C₂ rotation
C
A horizontal reflection
D
Identity
Question 90Single Answer
How is a vertical mirror plane oriented relative to the principal axis?
A
It is parallel to the axis and displaced from it
B
It is perpendicular to the axis
C
It contains the axis
D
It intersects the axis at 45°
Question 91Single Answer
Which point group describes ideal bent H₂O?
A
C₂h
B
C₂v
C
D₂h
D
Cₛ
Question 92Single Answer
Which point group describes ideal trigonal-pyramidal NH₃?
A
C₃v
B
D₃h
C
C₃h
D
D₃d
Question 93Single Answer
Which point group describes ideal trigonal-planar BF₃?
A
D₃h
B
D₃d
C
C₃h
D
C₃v
Question 94Single Answer
Which point group describes ideal square-planar XeF₄?
A
D₂d
B
C₄v
C
D₄h
D
C₂h
Question 95Single Answer
Which point group describes ideal staggered ethane?
A
D₃h
B
D₃d
C
C₃v
D
D₂h
Question 96Single Answer
Which point group describes ideal eclipsed ethane?
A
C₂v
B
C₃h
C
D₃d
D
D₃h
Question 97Single Answer
Which point group describes ideal linear HCl?
A
D∞h
B
C₂v
C
C∞v
D
D₂h
Question 98Single Answer
Which point group describes ideal linear CO₂?
A
D∞h
B
C∞v
C
C₂h
D
D₄h
Question 99Single Answer
A molecule has identity and one mirror plane as its only operations. Which point group applies?
A
Cₛ
B
Cᵢ
C
C₁
D
C₂
Question 100Single Answer
What is the order of the tetrahedral point group Td?
A
12
B
48
C
36
D
24
Question 101Single Answer
How many operations are in the 3σᵥ class of C₃v?
A
1
B
2
C
6
D
3
Question 102Single Answer
What does the character under the identity operation equal?
A
The number of classes
B
The group order
C
The dimension of the representation
D
The number of mirror planes
Question 103Single Answer
Which character under inversion identifies a one-dimensional ungerade representation?
A
−1
B
+1
C
0
D
+2
Question 104Single Answer
What is the orbital degeneracy of a T representation in cubic symmetry?
A
Twofold
B
Fourfold
C
Threefold
D
Onefold
Question 105Single Answer
How many irreducible representations does a point group with five conjugacy classes have?
A
2
B
5
C
10
D
4
Question 106Single Answer
In C₂v, a reducible representation has characters (6, 0, 2, 0). How many times does A₁ occur?
A
4
B
1
C
3
D
2
Question 107Single Answer
In C₃v, a representation has characters (9, 0, 1) for E, 2C₃ and 3σᵥ. How many copies of E occur?
A
1
B
2
C
4
D
3
Question 108Single Answer
In C₂v, what is the direct product B₁ × B₂?
A
A₂
B
A₁
C
B₁
D
B₂
Question 109Single Answer
In C₂v with z as the principal axis, which species describes the z translation?
A
A₁
B
A₂
C
B₂
D
B₁
Question 110Single Answer
In C₂v, which species describes rotation about the principal z axis?
A
A₁
B
A₂
C
B₁
D
B₂
Question 111Single Answer
How many vibrational normal coordinates does a nonlinear six-atom molecule have?
A
9
B
11
C
12
D
13
Question 112Single Answer
How many vibrational normal coordinates does a linear four-atom molecule have, counting degeneracies?
A
6
B
8
C
7
D
9
Question 113Single Answer
Which internal coordinate describes twisting about a bond?
A
Bond length
B
Bond angle
C
Centre-of-mass displacement
D
Dihedral angle
Question 114Single Answer
What must vary to first order along an infrared-active normal coordinate?
A
Net molecular charge
B
Total molecular mass
C
Nuclear spin
D
Electric dipole moment
Question 115Single Answer
Which property must vary to first order for a fundamental vibration to be Raman-active?
A
Permanent magnetic moment
B
Molecular mass
C
Nuclear quadrupole moment
D
Polarizability
Question 116Single Answer
In a centrosymmetric molecule, what does mutual exclusion imply for an IR-active fundamental?
A
It is Raman-inactive
B
It must also be Raman-active
C
It must be totally symmetric
D
It must be doubly degenerate
Question 117Single Answer
Which fundamental vibration of ideal CO₂ is Raman-active and IR-inactive?
A
Asymmetric stretching
B
One component of the bending mode
C
Symmetric stretching
D
Both components of the bending mode
Question 118Single Answer
Which C₃v symmetry species describes the NH₃ umbrella vibration?
A
E
B
A₂
C
A₁
D
B₂
Question 119Single Answer
A C₃ rotation cycles three equivalent stretching coordinates. What is its character in that basis?
A
+3
B
+1
C
0
D
−1
Question 120Single Answer
Reflection interchanges orthonormal ligand orbitals φ₁ and φ₂. Which SALC is antisymmetric?
A
(φ₁ + φ₂) ÷ √2
B
(φ₁ − φ₂) ÷ √2
C
(φ₁ − φ₂) ÷ 2
D
(φ₁ + φ₂) ÷ 2
Question 121Single Answer
Three orthonormal ligand orbitals φ₁, φ₂ and φ₃ are permuted by C₃v. Which normalized SALC is totally symmetric?
A
(φ₁ + φ₂ + φ₃) ÷ 3
B
(φ₁ − φ₂) ÷ √2
C
(φ₁ + φ₂ + φ₃) ÷ √3
D
(2φ₁ − φ₂ − φ₃) ÷ √6
Question 122Single Answer
Why do orbitals of different irreducible representations have zero coupling in a symmetry-preserving Hamiltonian?
A
Their off-diagonal Hamiltonian matrix element vanishes by symmetry
B
Their energies must be identical
C
Their occupancies must differ
D
They must lie on different atoms
Question 123Single Answer
Which central orbitals match the E′ ligand σ combinations in planar BF₃ lying in the xy plane?
A
s and p(z)
B
p(x) and p(z)
C
p(x) and p(y)
D
p(y) and p(z)
Question 124Single Answer
Which central valence orbitals match the A₁ + T₂ tetrahedral ligand σ set?
A
One s and three p orbitals
B
One s and two d orbitals
C
Three p orbitals only
D
Five d orbitals only
Question 125Single Answer
Which d orbital belongs to the classical square-planar dsp² set with bonds along x and y?
A
d(xy)
B
d(xz)
C
d(yz)
D
d(x² − y²)
Question 126Single Answer
Which pair generates two equivalent sp hybrids directed along ±z?
A
s and p(x)
B
s and p(z)
C
p(x) and p(y)
D
p(y) and p(z)
Question 127Single Answer
Which reaction occurs at the anode of a Zn–Cu galvanic cell?
A
Zn → Zn²⁺ + 2e⁻
B
Zn²⁺ + 2e⁻ → Zn
C
Cu²⁺ + 2e⁻ → Cu
D
Cu → Cu²⁺ + 2e⁻
Question 128Single Answer
What process occurs at the cathode in both galvanic and electrolytic cells?
A
Reduction
B
Oxidation
C
Neutralization
D
Hydrolysis
Question 129Single Answer
How do electrons travel through the external circuit of a working galvanic cell?
A
From cathode to anode
B
From salt bridge to cathode
C
From anode to cathode
D
From electrolyte to salt bridge
Question 130Single Answer
Oxidation generates metal cations in a galvanic anode compartment. Which salt-bridge ions migrate toward it?
A
Electrons
B
Cations
C
Both ions in equal amounts
D
Anions
Question 131Single Answer
What does the double vertical line in standard galvanic cell notation usually represent?
A
A salt bridge or liquid junction
B
A gas–liquid interface
C
An electrode surface
D
An external wire
Question 132Single Answer
What is the assigned standard potential of the standard hydrogen electrode?
A
+1.00 V
B
−0.0592 V
C
0.00 V
D
+0.0592 V
Question 133Single Answer
Which expression gives E°cell from standard reduction potentials?
A
E°anode + E°cathode
B
E°anode − E°cathode
C
E°cathode ÷ E°anode
D
E°cathode − E°anode
Question 134Single Answer
Cu²⁺/Cu and Zn²⁺/Zn have standard reduction potentials of +0.34 V and −0.76 V. What is the standard emf of the spontaneous cell?
A
−0.42 V
B
+0.42 V
C
+1.10 V
D
−1.10 V
Question 135Single Answer
Which couple contains the strongest oxidizing agent under standard conditions?
A
Ag⁺/Ag, +0.80 V
B
Fe²⁺/Fe, −0.44 V
C
Zn²⁺/Zn, −0.76 V
D
Cu²⁺/Cu, +0.34 V
Question 136Single Answer
Given E° = −0.76 V for Zn²⁺/Zn and −0.25 V for Ni²⁺/Ni, which reaction is spontaneous under standard conditions?
A
Ni + Zn²⁺ → Ni²⁺ + Zn
B
Both reactions
C
Zn + Ni²⁺ → Zn²⁺ + Ni
D
Neither reaction
Question 137Single Answer
A cell reaction is reversed. What happens to its standard emf?
A
It changes sign
B
It is halved
C
It remains unchanged
D
It doubles
Question 138Single Answer
A balanced cell equation is multiplied by three. What happens to E° and ΔG°?
A
Both triple
B
E° stays the same and ΔG° triples
C
E° triples and ΔG° stays the same
D
Both stay the same
Question 139Single Answer
Which relation connects ΔG with the reversible cell emf E?
A
ΔG = +nFE
B
ΔG = −FE ÷ n
C
ΔG = nF ÷ E
D
ΔG = −nFE
Question 140Single Answer
A reaction transfers two electrons and has E° = +0.400 V. What is ΔG°? Use F = 96,485 C mol⁻¹.
A
−38.6 kJ mol⁻¹
B
+38.6 kJ mol⁻¹
C
+77.2 kJ mol⁻¹
D
−77.2 kJ mol⁻¹
Question 141Single Answer
What does a positive standard cell emf imply for the equilibrium constant K?
A
K > 1
B
K = 1
C
K < 1
D
K = 0
Question 142Single Answer
At 25 °C, a two-electron reaction has E° ≈ 0.0887 V. What is K approximately?
A
100
B
10
C
1,000
D
10,000
Question 143Single Answer
Which expression is the reaction quotient for Zn(s) + Cu²⁺ → Zn²⁺ + Cu(s)?
A
Activity of Zn²⁺ divided by activity of Cu²⁺
B
Product of the two ionic activities
C
Activity of Cu²⁺ divided by activity of Zn²⁺
D
Reciprocal of the activity of Cu²⁺ alone
Question 144Single Answer
A two-electron cell has E° = 1.100 V at 25 °C. What is E when Q = 10?
A
1.130 V
B
1.159 V
C
1.041 V
D
1.070 V
Question 145Single Answer
What is the reversible cell emf when Q equals K?
A
E°
B
−E°
C
0 V
D
RT ÷ F
Question 146Single Answer
At 25 °C, how does a tenfold increase in Q change E for a one-electron cell reaction?
A
It decreases E by about 0.0592 V
B
It increases E by about 0.0592 V
C
It decreases E by about 0.0296 V
D
It leaves E unchanged
Question 147Single Answer
For Fe³⁺ + e⁻ → Fe²⁺, how does E change when the Fe³⁺ activity increases at fixed Fe²⁺ activity?
A
It increases
B
It becomes zero
C
It decreases
D
It stays constant
Question 148Single Answer
What is the hydrogen electrode potential at pH 4.00 and 25 °C with hydrogen at standard pressure?
A
+0.237 V
B
−0.118 V
C
−0.237 V
D
+0.118 V
Question 149Single Answer
The half-reaction O₂ + 4H⁺ + 4e⁻ → 2H₂O is at 25 °C. At fixed O₂ pressure, what happens to E when pH rises by one unit?
A
It rises by 0.0592 V
B
It falls by 0.2368 V
C
It falls by 0.0592 V
D
It rises by 0.0148 V
Question 150Single Answer
In a Cu²⁺ concentration cell with identical Cu electrodes, which side acts as the cathode?