📚 Exam by Category
▾
Objective Questions

Latest OPSC AEE Mechanical Exam Question (Objective Questions), MCQ in English

Subjects : Mechanical

Question Bank OPSC AEE Mechanical Prelims Exam - English
Back to Exam

Mechanical

Question 1Single Answer
Which of the following is the unit of kinematic viscosity _________________?
  1. A
    Pascal
  2. B
    Poise
  3. C
    Stoke
  4. D
    Faraday
  5. E
    None of the above
Question 2Single Answer
Consider the following processes:
1. Extension of a spring
2. Plastic deformation of a material
3. Magnetization of a material exhibiting hysteresis
Which of the above process are irreversible?
  1. A
    1 and 2 only            
  2. B
    1 and 3 only
  3. C
    1 only                        
  4. D
    1, 2 and 3
Question 3Single Answer
Which of the following statements are correct for a throttling process?
1. It is an adiabatic steady flow process
2. The enthalpy before and after throttling is same
3. In the processes, due to fall in pressure, the fluid velocity at outlet is always more than inlet velocity
  1. A
    1 and 2 only            
  2. B
    1 and 3 only
  3. C
    2 and 3 only                        
  4. D
    1, 2 and 3
Question 4Single Answer
A Reversed Carnot Engine removes 50 kW from a heat sink. The temperature of the heat sink is 250 K and the temperature of the heat reservoir is 300 K. The power required of the engine is
  1. A
    10 kW      
  2. B
    20 kW
  3. C
    30 kW    
  4. D
    50 kW
Question 5Single Answer
A heat engine receives heat at the rate of 2500 kJ/min and gives an output of 12.4 kW. Its thermal efficiency is, nearly
  1. A
    18%                        
  2. B
    23%
  3. C
    26%                        
  4. D
    30%
Question 6Single Answer
Consider the following motions :
1. Piston reciprocating inside an engine cylinder
2. Motion of a shaft between foot-step bearings
Which of the above can rightly be considered as successfully constrained motion?
  1. A
    1 only                     
  2. B
    2 only
  3. C
    Both 1 and 2           
  4. D
    Neither 1 nor 2
Question 7Single Answer
A rotor weighing 2 kN is supported on bearings A and B which are 1 m apart. The centre of mass of the rotor is at a distance 0.4 m from bearing A. It is observed that there is an unbalanced couple of magnitude 300 N-m which leaves the shaft balanced statically.The dynamic reactions at the supports will be
  1. A
    800 N and 800 N
  2. B
    300 N and 800 N
  3. C
    800 N and – 300 N
  4. D
    300 N and – 300 N
Question 8Single Answer
A cam is a mechanical member used to impart a desired motion to a follower by direct contact. Which one of the under-listed follower motion types will produce the least jerk to the system?
  1. A
    Simple harmonic
  2. B
    Constant acceleration and deceleration
  3. C
    Constant velocity
  4. D
    Cycloidal
Question 9Single Answer
In a circular are cam with a roller follower, acceleration of the follower depends on
1. cam speed and location of centre of circular arc
2. roller diameter and radius of circular arc
Which of the above is/are correct?
  1. A
    1 only                     
  2. B
    2 only
  3. C
    Both 1 and 2           
  4. D
    Neither 1 nor 2
Question 10Single Answer
A manufacturing company is selling a product for 15 per unit with variable cost of  10 per unit. The fixed cost of the asset is 50,000. How many units should be produced to breakeven?
  1. A
    2000                       
  2. B
    5000
  3. C
    8000                       
  4. D
    10000
Question 11Single Answer
A spherical waterdrop of 1 mm in diameter splits up in air into 64 smaller drops of equal size. The surface tension coefficient of water in air is 0.073 N/m. The work required in splitting up the drop is
  1. A
    0.96 × 10–6 J            
  2. B
    0.69 × 10–6 J
  3. C
    0.32 × 10–6 J            
  4. D
    0.23 × 10–6 J
Question 12Single Answer
Consider the following statements pertaining to stability of floating bodies:
1. A floating body will be stable when the centre of gravity is above the centre of buoyancy.
2. The position of metacentres corresponding to different axes of rotation are generally different for the same floating object.
3. For cargo ships, the metacentric height varies with loading.
Which of the above statements are correct?
  1. A
    1, 2 and 3                
  2. B
    1 and 2 only
  3. C
    1 and 3 only                        
  4. D
    2 and 3 only
Question 13Single Answer
Water is coming out from a tap and falls vertically downwards. At the tap opening, the stream diameter is 20 mm with uniform velocity of 2 m/s. Assuming steady inviscid flow, constant pressure atmosphere everywhere, and neglecting curvature and surface tension effects, the diameter of the stream 0.5 m below the tap opening is nearly
  1. A
    11.7 mm                  
  2. B
    14.6 mm
  3. C
    17.5 mm                  
  4. D
    20.4 mm
Question 14Single Answer
Consider the following statements:
1. At low Reynolds numbers of any flow, viscous forces dominate over inertial forces.
2. Transition from laminar to turbulent flow occurs over a range of Reynolds numbers depending on the surface presented to the flow.
Which of the above statements is/are correct?
  1. A
    1 only                     
  2. B
    2 only
  3. C
    Both 1 and 2           
  4. D
    Neither 1 nor 2
Question 15Single Answer
In a steady laminar flow of a given discharge through a circular pipe of diameter D, the head loss is proportional to
  1. A
    D–1                          
  2. B
    D–2
  3. C
    D–3                          
  4. D
    D–4
Question 16Single Answer
A fin will be more effective when Bio number is
  1. A
    Greater than 1
  2. B
    Equal to 1
  3. C
    Between 1 and 3
                   4        4
  4. D
    Less than 1
Question 17Single Answer
A tank of length, breadth and height in the ratio of 2:1:2 is full of water. The ratio of hydrostatic force at the bottom to that at any larger vertical surface is
  1. A
    1
  2. B
    2
  3. C
    3
  4. D
    4
Question 18Single Answer
Which of the following fluids exhibit a certain shear stress at zero shear strain rate followed by a straight line relationship between shear stress and shear strain rate?
  1. A
    Newtonian fluid 
  2. B
    Ideal Bingham plastic fluids
  3. C
    Pseudo-plastic fluids
  4. D
    Dilatent fluids
Question 19Single Answer
What is the specific gravity of a marble stone, which weighs 400N in air, and 200N in water? (g=10m/s2)
  1. A
    8
  2. B
    6
  3. C
    4
  4. D
    2
Question 20Single Answer
What is the intensity of pressure in the following SI units, when specific gravity of mercury is 13.6 and the intensity of pressure is 400KPa ?
  1. A
    0.3 bar or 4.077m of water or 0.29 mm of Hg
  2. B
    4 bar or 5.077m of water or 0.399 mm of Hg
  3. C
    0.3 bar or 5.077m of water or 0.599 mm of Hg
  4. D
    4 bar or 4.077m of water or 0.299 mm of Hg
Question 21Single Answer
If a submerged body displaced from its equilibrium position, returns to its original position, it is called __________.
  1. A
    thermal equilibrium
  2. B
    neutral equilibrium
  3. C
    unstable equilibrium
  4. D
    stable equilibrium
Question 22Single Answer
In a flow measurement, a venturi meter is preferred over an orifice plate because _____.
  1. A
    energy of head loss is less
  2. B
    It is cheaper
  3. C
    pressure drop is more
  4. D
    space is limited  
Question 23Single Answer
Pitot tube measures ______.
  1. A
    dynamic pressure of a moving stream
  2. B
    guage pressure
  3. C
    temperature of moving water
  4. D
    pressure difference between two fluids
Question 24Single Answer
Which of the following is not a property of an ideal fluid ?
  1. A
    flow is irrotational
  2. B
    it has no viscosity
  3. C
    it has viscosity
  4. D
    it is incompressible
Question 25Single Answer
Nozzle used in steam turbines convert ________.
  1. A
    enthalpy of steam into work
  2. B
    enthalpy of steam into kinetic energy
  3. C
    enthalpy of steam into pressure energy
  4. D
    pressure energy into work
Question 26Single Answer
Centroid of a uniform triangular lamina is located at?
  1. A
    1/2 from base
  2. B
    2/3 from base
  3. C
    1/3 from base
  4. D
    1/4 from base
Question 27Single Answer
Centroid of a uniform semicircular lamina from the flat edge is?
  1. A
    R/2
  2. B
    4R/3π
  3. C
    2R/3
  4. D
    R/π
Question 28Single Answer
Centre of gravity of a uniform solid hemisphere is located at?
  1. A
    3R/8 from base
  2. B
    R/2 from base
  3. C
    R/3 from base
  4. D
    4R/3π from base
Question 29Single Answer
Coplanar concurrent forces result in?
  1. A
    Translation only
  2. B
    Rotation only
  3. C
    Both translation and rotation
  4. D
    Equilibrium only
Question 30Single Answer
Lami’s theorem is applicable to?
  1. A
    Two forces
  2. B
    Three forces
  3. C
    Four forces
  4. D
    Any number of forces
Question 31Single Answer
A fluid is a substance that?
  1. A
    Continuously deforms under any applied shear stress
  2. B
    Resists all shear deformation
  3. C
    Has a fixed shape under all conditions
  4. D
    Cannot exert pressure
Question 32Single Answer
Which of the following is considered a fluid?
  1. A
    Liquid only
  2. B
    Both liquids and gases
  3. C
    Gas only
  4. D
    Solid only
Question 33Single Answer
An ideal fluid is generally assumed to be?
  1. A
    Compressible with surface tension only
  2. B
    Compressible and highly viscous
  3. C
    Incompressible and highly viscous
  4. D
    Incompressible and non-viscous
Question 34Single Answer
A real fluid possesses?
  1. A
    Zero density
  2. B
    Viscosity
  3. C
    Zero pressure
  4. D
    Infinite compressibility
Question 35Single Answer
According to Newton's law of viscosity, shear stress is proportional to?
  1. A
    Fluid density only
  2. B
    Pressure gradient only
  3. C
    Velocity gradient
  4. D
    Fluid depth
Question 36Single Answer
A fluid obeying Newton's law of viscosity is called a?
  1. A
    Newtonian fluid
  2. B
    Ideal solid
  3. C
    Perfect gas only
  4. D
    Plastic solid
Question 37Single Answer
The constant of proportionality in Newton's law of viscosity is called?
  1. A
    Bulk modulus
  2. B
    Surface tension
  3. C
    Dynamic viscosity
  4. D
    Specific weight
Question 38Single Answer
The SI unit of dynamic viscosity is?
  1. A
    Pa·s
  2. B
    N/m
  3. C
    kg/m³
  4. D
    m²/s²
Question 39Single Answer
The dimensions of dynamic viscosity are?
  1. A
    L²T⁻¹
  2. B
    MLT⁻²
  3. C
    ML⁻³
  4. D
    ML⁻¹T⁻¹
Question 40Single Answer
Kinematic viscosity is defined as the ratio of dynamic viscosity to?
  1. A
    Specific weight
  2. B
    Mass density
  3. C
    Pressure
  4. D
    Surface tension
Question 41Single Answer
An internal combustion engine is an engine in which fuel combustion occurs?
  1. A
    Only in the exhaust pipe
  2. B
    Only in an external boiler
  3. C
    Inside the engine cylinder or combustion chamber
  4. D
    Outside the engine completely
Question 42Single Answer
In a spark-ignition engine, ignition of the charge is initiated by?
  1. A
    Fuel injector only
  2. B
    Spark plug
  3. C
    Compression alone
  4. D
    Exhaust valve
Question 43Single Answer
In a compression-ignition engine, fuel ignites mainly due to?
  1. A
    Spark plug discharge
  2. B
    High temperature of compressed air
  3. C
    External flame
  4. D
    Battery heating only
Question 44Single Answer
The fuel commonly used in SI engines is?
  1. A
    Heavy furnace oil only
  2. B
    Diesel only
  3. C
    Petrol or gasoline
  4. D
    Coal slurry
Question 45Single Answer
The fuel commonly used in conventional CI engines is?
  1. A
    Kerosene exclusively
  2. B
    Petrol only
  3. C
    Diesel
  4. D
    LPG only
Question 46Single Answer
In a four-stroke SI engine, one power stroke occurs in?
  1. A
    Four crankshaft revolutions
  2. B
    One crankshaft revolution
  3. C
    Two crankshaft revolutions
  4. D
    Half crankshaft revolution
Question 47Single Answer
In a two-stroke engine, one power stroke generally occurs in?
  1. A
    Every four revolutions
  2. B
    Every two crankshaft revolutions
  3. C
    Every crankshaft revolution
  4. D
    Every six revolutions
Question 48Single Answer
The compression ratio of a CI engine is generally?
  1. A
    Always equal to that of an SI engine
  2. B
    Lower than that of an SI engine
  3. C
    Higher than that of an SI engine
  4. D
    Independent of ignition method
Question 49Single Answer
The main reason for using a high compression ratio in CI engines is to?
  1. A
    Eliminate fuel injection
  2. B
    Reduce air temperature
  3. C
    Raise air temperature sufficiently for self-ignition
  4. D
    Reduce cylinder pressure
Question 50Single Answer
The ideal air-standard cycle for an SI engine is the?
  1. A
    Diesel cycle
  2. B
    Otto cycle
  3. C
    Rankine cycle
  4. D
    Brayton cycle
Important Questions Package

OPSC AEE Mechanical Exam Online Question Bank Package

Buy OPSC AEE Mechanical Important Questions, MCQ, question answer in Hindi & English. It will help you to score high marks in OPSC AEE Mechanical question bank 2026 in Online, PDF & Print study material.

+ Free Monthly Current Affairs, GK & more PDF Download
Sr.Package NameAmount
1.OPSC AEE Mechanical Mains Exam Paper I - English
Description : 1000 Question with Answer
₹101 [₹500]
2.OPSC AEE Mechanical Mains Exam Paper I - English
Description : 1500 Question with Answer
₹131 [₹500]
3.OPSC AEE Mechanical Mains Exam Paper I Question Bank Book - English
Description : 1000 Question with Answer (Printed Material)
₹390 [₹600]
4.OPSC AEE Mechanical Mains Exam Paper I - English
Description : 1000 Question & Answer Download in PDF (Send by Email)
₹151 [₹450]
5.OPSC AEE Mechanical Prelims Exam - English
Description : 1000 Quesiton with Answer.
₹101 [₹500]
6.OPSC AEE Mechanical Prelims Exam - English
Description : 2000 Question with Answer.
₹151 [₹500]
7.OPSC AEE Mechanical Prelims Exam - English
Description : 3000 Question with Answer.
₹181 [₹500]
8.OPSC AEE Mechanical Prelims Exam - English
Description : 3500 Question with Answer.
₹191 [₹500]
Back to Exam
Question for OPSC AEE Mechanical 2026 - Quiz / Questions / MCQ - Toppersexam