A boat can travel with a speed of 13 km/hr in still water. If the speed of the stream is 4 km/hr, find the time taken by the boat to go 68 km downstream .
A
2 hours
B
3 hours
C
4 hours
D
5 hours
Question 2Single Answer
Sum of digit of a two-digit number is 15 and the difference between the digits is 3. What is the two digit number ?
A
69
B
96
C
78
D
Cannot be determined
E
None of these
Question 3Single Answer
The sum of three consecutive integers is 30. Which of the following is the largest among the three ?
A
12
B
13
C
14
D
10
E
None of these
Question 4Single Answer
Mr. Sinha distributes a certain sum of money among his five sons, one daughter and his wife in such a way that each son gets double the amount of his daughter and the wife gets double the amount of each son. If each son gets Rs. 15000, what was the total amount distributed ?
A
Rs. 123000
B
Rs. 112500
C
Rs. 138500
D
Rs. 132500
Question 5Single Answer
Which is the largest of the following fractions ?
A
B
C
D
Question 6Single Answer
The sum of 3 consecutive even numbers is 198. Which of the following will be the smallest number among them ?
A
42
B
38
C
32
D
72
E
None of these
Question 7Single Answer
Two third of half of a number is 18. What is one third of that number ?
A
18
B
16
C
19
D
17
E
None of these
Question 8Single Answer
The difference between th of th of a number and of th of the same number is 9. What in the number.
A
45
B
35
C
40
D
30
E
None of these
Question 9Single Answer
If is subtracted from and the difference is multiplied by 504, what will be the number ?
A
2024
B
2104
C
2004
D
2014
E
None of these
Question 10Single Answer
‘a’ is greater than ‘b’ by 2 and ‘b’ is greater than ‘c’ by 10. If a+b+c = 130 then (b+c) - a = ?
A
38
B
42
C
44
D
34
E
None of these
Question 11Single Answer
The product of two successive positive integers is 462. Which is the smaller integer ?
A
20
B
22
C
21
D
23
E
None of these
Question 12Single Answer
If the difference between a number and two fifth of the number is 30, find the number .
A
50
B
75
C
57
D
60
E
None of these
Question 13Single Answer
IF the sum of four consecutive even number is 228. Which is the smallest of the number ?
A
52
B
54
C
56
D
48
E
None of these
Question 14Single Answer
If the following fractions are arranged in descending order which will be the last in the series ?
A
B
C
D
Question 15Single Answer
What is the least number to be added to 3986 to make it a perfect square ?
A
118
B
95
C
110
D
100
E
None of these
Question 16Single Answer
What is 234 time 167 ?
A
48768
B
41184
C
40581
D
39078
E
None of these
Question 17Single Answer
The product of two consecutive even number is 4488. Which is the smaller number ?
A
62
B
71
C
66
D
65
E
None of these
Question 18Single Answer
If the fractions are arranged in ascending order of their values, which one will be the fourth ?
A
B
C
D
Question 19Single Answer
What is the least number to be added to 1416 to make it perfect square ?
A
47
B
38
C
28
D
25
E
None of these
Question 20Single Answer
What is 147 times 329 ?
A
48069
B
48363
C
49021
D
48723
E
None of these
Question 21Single Answer
The sum of 5 consecutive even number A, B, C, D and E is 410. What is the product of A and E ?
A
6708
B
6880
C
6552
D
Cannot be determined
E
None of these
Question 22Single Answer
The product of two consecutive odd number is 6399. What is the smaller number ?
A
83
B
79
C
81
D
77
E
None of these
Question 23Single Answer
If the fractions are arranged in descending order of their values, which one will be the fourth ?
A
B
C
D
E
None of these
Question 24Single Answer
What is 394 times 113 ?
A
44402
B
44632
C
44802
D
44522
E
None of these
Question 25Single Answer
What is the least number to be added to 7700 to make it a perfect square ?
A
131
B
221
C
77
D
98
E
None of these
Question 26Single Answer
What least number should be added to 8602 to make if a perfect square ?
A
234
B
47
C
128
D
36
E
None of these
Question 27Single Answer
What is 846 times 323 ?
A
280872
B
276488
C
273258
D
272412
E
None of these
Question 28Single Answer
The sum of the two digits of a two digit number is 15 and the difference between the two digits of the two digit number is 3 . What is the product of the two digits of the two digit number ?
A
72
B
56
C
54
D
Cannot be determined
E
None of these
Question 29Single Answer
If the fractions are arranged in ascending order of their values, Which fraction will be the fifth ?
A
B
C
D
E
None of these
Question 30Single Answer
The product of two consecutive odd numbers is 4623. What is the product of the next two consecutive odd numbers ?
A
4899
B
4891
C
5037
D
5183
E
None of these
Reasoning
Question 31Single Answer
How many such pairs of letters are there in the word ‘CLEANLINESS’ each of the which has as many letters between them in the word as they have in the English alphabet, in the same sequence?
A
Two
B
Three
C
Five
D
Four
E
None of these
Question 32Single Answer
Team A has scored more goals than Team B
Team C has scored fewer goals than Team B
Team A has scored fewer goals than Team C .
If the first two statements are true, the third statement is
A
True
B
False
C
Uncertain
D
None
Question 33Single Answer
If it is possible to make only one meaningful word with the second, the third, the sixth and the eight letters of the word FRAGMENT using each only once, which of the following will be the third letter of that word ? If no such word can be formed, give ‘X’ as the answer and if more than one such word can be formed, give ‘Y’ as the answer.
A
A
B
E
C
T
D
X
E
Y
Question 34Single Answer
How many such letters are there in the word ORIENTAL each of which is as far away from the beginning of the word as when they are arranged alphabetically?
A
None
B
One
C
Two
D
Three
E
More than three
Question 35Single Answer
How many such pairs of letters in the word CREDIT each of which has as many letters between them in the word as in the English alphabet?
A
None
B
One
C
Two
D
Three
E
More than three
Question 36Single Answer
How many meaningful words can be made from the letters ‘LMEA’ using each letter only once in each word?
A
None
B
One
C
Two
D
Three
E
More than three
Question 37Single Answer
If it is possible to make only one meaningful word with the first, the second, the seventh and the eighth letters of the word TEMPORAL, which of the following will be the first letter of that word? If more than one such word can be made, give ‘Y’ as the answer and if no such word can be made, give ‘X’ as the answer.
A
T
B
L
C
E
D
Y
E
X
Question 38Single Answer
If the letters of the word HANDOVER are arranged alphabetically from left to right how many letters will remain at the same position?
A
None
B
One
C
Two
D
Three
E
More than three
Question 39Single Answer
How many such pairs of letters are there in the word EXCURSION, each of which has as many letters between them in the word as they have in the English alphabet?
A
None
B
One
C
Two
D
Three
E
More than three
Question 40Single Answer
If it is possible to make only one meaningful word with the first, the second, the third, the sixth and the eighth letters of the word DEVIATION first letter of that word is your answer? If more than one such word can be made formed your answer is ‘A’ and if no such word can be formed your answer is ‘B’.
A
V
B
T
C
E
D
A
E
B
English
Question 41Single Answer
I go to Madurai by —– Vaigai Express
A
a
B
an
C
some
D
the
Question 42Single Answer
Have the car stolen!
A
Steal the car
B
You should have the stolen car
C
Get someone to steal the car
D
They have stolen the car
Question 43Single Answer
The payment was collected by the hardworking salesman.
A
The hardworking salesman collected the payment.
B
the salesman who worked heard was able to collect the payment.
C
to collect the payment the salesman had to work hard.
D
The hardworking salesman was able to collect the payment.
Question 44Single Answer
I had to stop all my work to complete this project.
A
All other work had to be stopped to complete this project by me
B
For completing this project all other work must be stopped
C
For completing this project I had to stop all my work
D
To complete this project all other work had been stopped by me
Question 45Single Answer
They have published the names of all the successful candidates.
A
The candidates who have succeeded their names they had published.
B
The names of all the successful candidates have been published by them
C
The candidates who have succeeded their names have been published by them.
D
The names of all the successful candidate were published by them.
Question 46Single Answer
The online shopping site lowered the prices.
A
Lowering of the prices was done by the online shopping site
B
The prices were lowered by the online shopping site
C
The prices had been lowered by the online shopping site
D
The prices have been lowered by the online shopping site
Question 47Single Answer
Who taught you to drive a truck ?
A
To drive a truck by whom were you taught?
B
Driving a truck by who were you taught?
C
Driving a truck by who were you being taught?
D
By whom were you taught to drive a truck?
Question 48Single Answer
We shall invite Suresh.
A
Suresh would be invited by us
B
Suresh would have been invited by us
C
Suresh will be invited by us
D
Suresh will have been invited by us
Question 49Single Answer
Dark clouds have overcast the evening sky.
A
By the dark clouds the evening sky was overcast.
B
The evening sky has been overcast by the dark clouds.
C
Dark clouds overcastted the evening sky.
D
The sky of the evening was overcasted by dark clouds.
Question 50Single Answer
The partners will celebrate their triumph tomorrow.
A
The triumph would be celebrated by the partners a day before
B
The triumph would be celebrated by the partners a day after
C
The triumph would have been celebrated by the partners a day after
D
The triumph will have been celebrated by the partners tomorrow
Important Questions Package
HEC Diploma Engineer Trainee Exam Online Question Bank Package
Buy HEC Diploma Engineer Trainee Important Questions, MCQ, question answer in Hindi & English. It will help you to score high marks in HEC Diploma Engineer Trainee question bank 2026 in Online, PDF & Print study material.
+ Free Monthly Current Affairs, GK & more PDF Download
Sr.
Package Name
Amount
1.
HEC Diploma Engineer Trainee Exam (Civil) - English
Description : 2000 Question With Answer
₹151[₹500]
2.
HEC Diploma Engineer Trainee Exam (Civil) - Hindi
Description : 2000 Question With Answer
₹181[₹500]
Civil Engineering
Question 51Single Answer
One bag of Portland cement, 50 kg in weight, would normally have a bulk volume of
A
30 l
B
35 l
C
40 l
D
45 l
Question 52Single Answer
AsCu, a preservative for wood, developed by the Forest Research Institute, Dehradun, comprises of chemicals:
A
1 : 1 : 1
B
1 : 2 : 3
C
1 : 2 : 4
D
1 : 3 : 4
Question 53Single Answer
Consider the following statements related to autoclave bricks:
1.Less water absorption compared to other bricks.
2.Noise reduction
3.It is cheap compared to other types of bricks.
4.Requirement of bulk volume of mortar in joints being relatively less compared to other types of brick masonry.
5.Not recommended for outer walls.
Which of the above statements are relevant to the use of ‘autoclave’ bricks?
A
1, 2 and 4
B
1, 3 and 5
C
2, 3 and 4
D
2, 4 and 5
Question 54Single Answer
The minimum number of annular rings to be seen in every 2.54 cm in the radial direction from the core for timber to be classified as ‘Dense’ is
A
10
B
20
C
25
D
30
Question 55Single Answer
If the actual thickness of a brick masonry wall is 19 cm, its effective length is 2.70 m, its effective height is 2.82 m and its code specified stiffening coefficient is 1.2 then, for design considerations, the slenderness ratio of the wall will be taken as
A
11.8
B
12.4
C
14.2
D
14.8
Question 56Single Answer
Consider the following forms of water in a hydrated cement paste:
1.Capillary water
2.Chemically combined water
3.Interlayer water
4.Adsorbed water
Which of the above forms of water will, on its/their removal, cause shrinkage of the paste?
A
1, 2 and 3
B
1, 2 and 4
C
2, 3 and 4
D
1, 3 and 4
Question 57Single Answer
Consider the following statements:High early strength of cement is obtained as a result of
1.Fine grinding.
2.Decreasing the lime content
3.Burning at higher temperature
4.Increasing the quality of gypsum.
Which of the above statements are correct?
A
1 and 2
B
1 and 3
C
2 and 3
D
3 and 4
Question 58Single Answer
Consider the following statements related to ‘composite mortar’:
1.Addition of lime to cement mortar improves its workability
2.Composite mortar is obtained by adding 10% by weight of cement and mixing with water.
3.Composite mortar is not preferred in tall buildings.
4.Mechanical grinding is essential for developing composite mortar.Which of the above statements are true in this case?
A
1, 2 and 3 only
B
1, 3 and 4 only
C
2, 3 and 4 only
D
1, 2, 3 and 4
Question 59Single Answer
Consider the following statements related to ‘non-destructive testing’ of concrete:
1.Indentation test is used to assess the quality of concrete.
2.Resonant Frequency Method is based on a laboratory test.
3.Compressive strength of concrete is estimated through Pulse Velocity Measurement.
4.Dynamic modulus of Elasticity is determined by a Sonometer Test.
5.Thickness of concrete can be estimated by in-situ Rebound Hammer Test.
Which of the above statements are correct?
A
1, 2 and 3 only
B
1, 2 and 5 only
C
1, 2, 3 and 4 only
D
1, 2, 3, 4 and 5
Question 60Single Answer
What is the amount of water required for a workable RC of mix 1 : 2: 4 by weight., when W/C is 0-60 and unit weight of concrete is 2400 kg/m3?
A
165 l
B
205 l
C
245 l
D
285 l
Question 61Single Answer
Which IS code is used for classification of timber for seasoning purposes?
A
IS : 4970-1973
B
IS : 1708-1969
C
IS : 1141-1958
D
IS : 399-1963
Question 62Single Answer
Consider the following with regard to the application of preservation of timber:
1.Increase in the life span of the member
2.Increase in the strength of the timber
3.Removal of moisture
4.Prevention of growth of fungi by killing them
Which of the above are correct?
A
1, 2, 3 and 4
B
2 and 4 only
C
1 and 4 only
D
2 and 3 only
Question 63Single Answer
The plies in plywood are so placed that the grains of each ply are
A
Parallel to each other
B
At right angle to one another
C
45° oblique to adjacent grain
D
Not constrained by any consideration
Question 64Single Answer
Which of the following is an ODD one as regards ‘requirement of good brick-earth’?
A
It must be free from lumps of lime
B
It should not be mixed with salty water
C
It must be non-homogeneous
D
It should not contain vegetable and organic matter
Question 65Single Answer
The compressive strength of heavy-duty bricks, as per IS : 2980-1962, should not be less than
A
440 kg/cm2
B
175 kg/cm2
C
100kg/cm2
D
75kg/cm2
Question 66Single Answer
Consider the following statements:
1.Brickwork will have high water tightness.
2.Brickwork is preferred for monument structures.
3.Bricks resist fire better than stones
4.Bricks of good quality shall have thin mortar bonds.
Which of the above statements are correct?
A
1 and 2
B
3 and 4
C
2 and 3
D
1 and 4
Question 67Single Answer
Consider the following statements:A good soil for making bricks should contain
1.30% alumina
2.10% lime nodules
3.Only small quantity of iron oxides
4.15% magnesia
Which of the above statements are correct?
A
1 and 2 only
B
1 and 3
C
1, 2 and 4
D
2, 3 and 4
Question 68Single Answer
Which compound of cement is responsible for strength of cement?
A
Magnesium oxide
B
Silica
C
Alumina
D
Calcium sulphate
Question 69Single Answer
Which type of cement is recommended in large mass concrete works such as a dam?
A
Ordinary Portland
B
High Alumina
C
Low-heat Portland
D
Portland Cement
Question 70Single Answer
Consider the following statements regarding ‘setting of cement’:
1.Low-heat cement sets faster than OPC.
2.Final setting time decides the strength of cement
3.Initial setting time of Portland Pozzollona is 30 minutes
4.Air-induced setting is observed when stored under damp conditions.
4.Addition of gypsum retards the setting time.
Which of the above statements are correct?
A
1, 2 and 3
B
2, 3 and 4
C
3, 4 and 5
D
2, 3 and 5
Question 71Single Answer
Consider the following statements regarding ‘strength of cement’:
1.Strength test on cement is made on cubes of cement-sand mix.
2.Water to be used for the paste is 0.25 P, where P is the water needed for normal consistency.
3.The normal consistency is determined on Le Chatelier’s principle.
4.Cubes are cast in two layers in leak-proof moulds further compacted in each layer by vibration on a machine.
Which of the above statements are correct?
A
1 and 2
B
2 and 3
C
1 and 4
D
3 and 4
Question 72Single Answer
Which of the following ingredients refer to binding material of mortar?
1.Cement
2.Lime
3.Sand
4.Ashes
Select the correct answer using the code given below.
A
1 and 4
B
3 and 4
C
1 and 2
D
2 and 3
Question 73Single Answer
Consider the following statements:
1.Bricks in masonry are bound by mortar.
2.Mortars make brick damp-proof.
3.Strength of brick in masonry is improved by plastering.
4.Addition of lime improves workability.
5.Marine construction needs sulphate-resistant cement mortar.
Which of the above statements are relevant for ‘cement mortar’?
A
1, 2 and 3
B
2, 3 and 4
C
1, 4 and 5
D
3, 4 and 5
Question 74Single Answer
Consider the following parameters of concrete:
1.Impermeability
2.Compactness
3.Durability
4.Desired consistency
5.Workability
Which of the above parameters are relevant for ‘water-cement ratio’?
A
4 and 5
B
1 and 2
C
2 and 4
D
3 and 5
Question 75Single Answer
Consider the following statements:Presence of Na2O and K2O in concrete leads to
1.Expansive reaction in concrete
2.Cracking of concrete
3.Disruption of concrete
4.Shrinkage of concrete
Which of the above statements are correct?
A
1 and 2 only
B
2 and 3 only
C
1, 2 and 3
D
3 and 4
Question 76Single Answer
The maximum total quantity of dry aggregate by mass per 50 kg of cement, to be taken as the sum of the individual masses of fine and coarse aggregates (kg), for M20 grade of concrete is
A
625
B
480
C
330
D
250
Question 77Single Answer
Absorption capacity of an aggregate refers to the difference expresses in appropriate proportion in water content between
A
A wet aggregate and a dry aggregate
B
A dry aggregate and a wet aggregate
C
A saturated surface-dry aggregate and a dry aggregate
D
A saturated surface-dry aggregate and an over dry aggregate
Question 78Single Answer
Consider the following statements concerning ‘elasticity of concrete’:
1.Stress-strain behavior of concrete is a straight line up to 10% ultimate stress.
2.Strain determination is obtained from tangent modulus.
3.Modulus of elasticity of concrete is also called as secant modulus.
Which of the above statements are correct?
A
1, 2 and 3
B
1 and 3 only
C
1 and 2 only
D
2 and 3 only
Question 79Single Answer
Consider the following statements :The addition of CaCl2 in concrete results in
1.Increased shrinkage
2.Decreased setting time
3.Decreased shrinkage
4.Increased setting time
Which of the above statements are correct?
A
1 only
B
2 and 3
C
3 and 4
D
1 and 2
Question 80Single Answer
Which of the following statements are correct ?
1.Knots in a tree affect the continuity of fibres.
2.Nail knots do not influence the strength of timber.
3.Druxiness of wood is not a defect.
4.Tall trees with twisted fibers give good timber for poles.
A
1, 2, 3 and 4
B
1, 2 and 4 only
C
1, 2 and 3 only
D
2, 3 and 4 only
Question 81Single Answer
Excrescences in wood are
1.Defects found in trees
2.Formed due to injuries inflicted on trees when they are growing
3.Defects which render wood suitable as firewood only
A
1, 2 and 3
B
1 and 2 only
C
1 and 3 only
D
2 and 3 only
Question 82Single Answer
What treatment is adopted for making timber fire-resistant?
A
ASCU treatment
B
Abel’s process
C
Creosoting
D
Tarring
Question 83Single Answer
Deterioration of structure of timber due to dry rot is:
1.Caused by fungi
2.Due to dry-spell after heavy rains
3.Due to attack of termites
4.ndicated by surface stripes on scantlings
A
1 and 2
B
3 and 4
C
2 and 3
D
1 and 4
Question 84Single Answer
Alternate wetting and drying of timber :
1.Results in shrinkage and swelling
2.Brings about wet rot onset
3.Increases the durability
4.Causes transmission of spores from germination
A
1, 2, 3 and 4
B
1, 2 and 4 only
C
1, 2 and 3 only
D
2, 3 and 4 only
Question 85Single Answer
As per I.S. classification, the minimum compressive strength of a first class brick should be
A
75 kg/cm3
B
100kg/cm3
C
125 kg/cm3
D
150 kg/cm3
Question 86Single Answer
When provided with alternating courses of (a) all headers and (b) all stretchers, the front elevation of such brick masonry is designated as
A
English bond
B
Single Flemish bond
C
Double Flemish bond
D
Rat-trap bond
Question 87Single Answer
I.S. code specifies that the compressive strength of brick shall be determined by keeping the brick:
1.On edge
2.On bed
3.After soaking in water for 2 hrs
4.After soaking in water for 24 hrs
A
1 and 2
B
2 and 3
C
3 and 4
D
2 and 4
Question 88Single Answer
Soundness test of cement is carried out to determine its
A
Alumina content
B
Iron oxide content
C
Free lime content
D
Durability under sea water
Question 89Single Answer
The objectives of producing cement include:
1.Incorporating industrial wastes
2.Increasing free lime
3.Increasing fineness
4.Saving energy needed in the process
A
1, 2, 3 and 4
B
1, 3 and 4 only
C
1, 2 and 4 only
D
2, 3 and 4 only
Question 90Single Answer
A mild steel rod tapers uniformly from 24 mm mm dia. over its length of 400 mm. The rod when held vertical is subjected to an axial tensile load of 12 kN. E = 2 × 105 N/mm2. The extension of the rod in mm would be:
A
3
2
B
2
3
C
3
D
1
3
Question 91Single Answer
Two different liquids are flowing through different pipes of the same diameter. In the first pipe, the flow is laminar with centerline velocity,Vmax.1,Whereas in the second pipe, the flow is turbulent. For turbulent flow, the average velocity is 0.82 times the centerline velocity,vmax.2 . For equal volumetric flow rates in both the pipes, the ratio Vmax.1/Vmax.2(up to two decimal place) is_____.
A
1.64
B
2.45
C
0.25
D
1.44
Question 92Single Answer
Poisson’s ratio of a material is 0.3. Then the ratio of Young’s modulus to bulk modulus is
A
0.6
B
0.8
C
1.2
D
1.4
Question 93Single Answer
For a gas phase cracking reaction A→B+C at 300℃ , the Gibbs free energy of the reaction at this temperature is ∆G°= -2750J/mol . The pressure is 1 bar and the gas phase can be assumed to be ideal. The universal gas constant =8.314J/mol. K. The fractional molar conversion of A at equilibrium is________.
A
0.44
B
0.50
C
0.64
D
0.80
Question 94Single Answer
Which of the following statements are correct ?
1.In a ductile material elastic deformation is more predominant than plastic one.
2.Brittleness is not an absolute property of a metal.
3.Rate of loading has no influence in changing the behavior of a metal from ‘ductile’ to ‘brittle’ at low temperatures
4.Under hydrostatic compression, a brittle metal may change into a ductile one.
A
1 and 2
B
2 and 3
C
3 and 4
D
2 and 4
Question 95Single Answer
The total deflection of a structure when subjected simultaneously to different sets of loading is equal to the sum of the deflections under each such set of loads as if acting separately on the structure. Which one the following justifies this statement?
A
Elastic limit is not exceeded
B
Elastic limit including buckling is not exceeded
C
Limit state is not exceeded
D
Proportional limit without buckling is not exceeded
Question 96Single Answer
A rectangular bar of cross-sectional area a is subjected to an axial tensile load P. The maximum shear stress will occur on a plane at X° to any normal cross-section where X° is
A
90°
B
27°
C
180°
D
45°
Question 97Single Answer
A solid circular shaft has been subjected to a pure torsion moment. The ratio of maximum shear stress to maximum normal stress at any point would be
A
1 : 2
B
1 : 1
C
2 : 3
D
2 : 1
Question 98Single Answer
Which of the following statements are correct?
1.All load carrying members transmit load through basic modes of tension, compression, torsion and shear only.
2.Beams carry transverse loads.
3.Combined loading is a complicated loading.
4.Nature of internal forces decides the aspect of combines loading.
A
1 and 2
B
2 and 3
C
3 and 4
D
2 and 4
Question 99Single Answer
Identify the WRONG statement amongst the following:
A
steam distillation is used for mixtures that re immiscible with water.
B
Vacuum distillation is used for mixtures that are miscible with water.
C
Steam distillation is used for mixtures that are miscible with water.
D
vacuum distillation columns have larger diameter as compared to atmospheric columns for the same throughout
Question 100Single Answer
Which of the following statements are correct?
1.Experimental results on thin-walled tubes show that maximum normal stress theory is valid.
2.Normal-stress theory is valid in case of brittle materials.
3.In case of pure shear, St. Venant’s theory is more valid than other theories.
4.Tresca’s theory is very closely substantiated by experimental results.
5.In maximum stress theory, the yield locus is a hexagon.
A
1, 2 and 3
B
2, 4 and 5
C
1, 2 and 4
D
2, 3 and 4
Question 101Single Answer
A thin cylindrical shell made of mild steel plate is 1000 mm in diameter. It is to be subjected to an internal pressure of 2 N/mm2. If the material yields at 200N/mm2, the thickness of the plate in mm on the basis of Rankine’s theory of failure with assuming a factor of safety of 3 would be
A
10
B
12
C
15
D
18
Question 102Single Answer
Which of the following can change if only the catalyst is changed for a reaction system?
A
Enthalpy of reaction
B
Activation energy
C
Free Energy of the reaction
D
Equilibrium constant
Question 103Single Answer
Which of the following loads should be applied on a simply supported beam, so that the shear force is constant throughout its span?
A
U.D.L. over the entire span.
B
Two concentrated loads equally spaced in the span.
C
A central concentrated load and a U.D.L. over the entires pan.
D
A couple anywhere in the span.
Question 104Single Answer
A simply supported rolled steel joist of I-section has flange width 250 mm and overall depth 600 mm. Its moment of inertia IXX = 12 × 106 mm4. The steel joist is used as a beam over a simply supported span of 6m. It carries a load of 40 kN/m including its self weight throughout the span. The maximum stress induced in the beam in N/mm2 due to bending would be
A
30
B
90
C
45
D
60
Question 105Single Answer
Which of the following terms represents the torque that produces a twist of one radian in a shaft of unit length?
A
Torsional stress
B
Torsional rigidity
C
Flexural rigidity
D
Moment of resistance
Question 106Single Answer
A 60 mm dia. shaft is subjected to a torque of 6 kN-m. C = 8 × 104 N/mm2. The maximum shear stress induced in the shaft in N/mm2will be
A
8000
92
B
4000
9
C
12000
9
D
16000
9
Question 107Single Answer
A water main 160 cm dia. contains water at a pressure head of 200m. Take weight of water to be 1000 kg/m3. The thickness of the metal shell required for the water main, given that the maximum permissible stress in the metal is 400kg/cm2, will be
A
1 cm
B
2 cm
C
3 cm
D
4 cm
Question 108Single Answer
The radial splits which are wider on the outside of the log and narrower towards the pith are known as
A
Star shakes
B
Annular rings
C
Cup shakes
D
Hear shakes
Question 109Single Answer
Consider the following distinguishing characteristics of hardwood:
1.They have distinct annular rings.
2.They are not resinous.
Which of these characteristics of hardwood is/are correct?
A
1 only
B
2 only
C
Both 1 and 2
D
Neither 1 nor 2
Question 110Single Answer
Consider the following statements on the specific gravity of wood:
1.It is always greater than 2.
2.It is less than 1.
3.It is not dependent upon temperature and equilibrium moisture content.
Which of these statements are correct?
A
1, 2, 3 and 4
B
1 and 3 only
C
2 and 3 only
D
2 and 4 only
Question 111Single Answer
The age of a log of timber can be estimated by
A
Diameter of pith
B
Thickness of bark
C
Number of annular rings
D
Number of medullary rays
Question 112Single Answer
Consider the following statements:Seasoning of timber results in
1.Increased strength
2.Increased durability
3.Reduced resilience
4.Increased dimensional stability
Which of these statements are correct?
A
1, 2 and 4
B
1, 2 and 3
C
1, 3 and 4
D
2, 3 and 4
Question 113Single Answer
Match List-I and List-II and select the correct answer using the code given below the lists: List-I List-II
Plywood 1. Furniture
Fiberboard 2. Cantilever arches
Laminated lumber 3. Insulation
Commercial blockboard 4. Lining of form-work in concrete Codes:
A
A B C D
1 2 3 4
B
4 3 2 1
C
4 2 3 1
D
4 2 3 1
Question 114Single Answer
Consider the following statements:Perforated bricks are preferred in construction since
1.They are lighter
2.They are stronger than class 1 bricks
3.They have heat-insulating properties
4.They are cheaper and need less mortar
Which of these statements are correct?
A
1, 2, 3 and 4
B
2 and 3 only
C
1 and 3 only
D
3 and 4 only
Question 115Single Answer
The standard size of a brick is
A
20 cm × 10 cm × 10 cm
B
19 cm × 9 cm × 9 cm
C
18 cm × 9 cm × 9 cm
D
18 cm × 10 cm × 10 cm
Question 116Single Answer
Consider the following statements:More than 6% magnesium oxide by weight in cement results in
1.High early strength and high heat generation
2.Less tendency towards volume change and formation of cracks
Which of these statements is/are correct?
A
1 only
B
2 only
C
Neither 1 nor 2
D
Both 1 and 2
Question 117Single Answer
Fineness if cement is measured in the units of
A
Volume/mass
B
Mass/volume
C
Area/mass
D
Mass/area
Question 118Single Answer
The initial setting time of cement depends most on
A
Tricalcium aluminate
B
Tricalciumaluminoferrite
C
Dicalcium silicate
D
Dicalcium silicate
Question 119Single Answer
Consider the following statements:Sand in cement mortar is used for
1.Increasing the strength
2.Reducing the shrinkage
3.Decreasing the surface area of the binding material
4.Decreasing the quantity of cement
Which of these statements are correct?
A
1, 2 and 4
B
1, 2 and 3
C
1, 3 and 4
D
2, 3 and 4
Question 120Single Answer
Consider the following statements:
1.The compressive strength of concrete decreases with increase in water-cement ratio of the concrete mixture.
2.Water is added to the concrete mix for hydration of cement and workability.
3.Creep and shrinkage of concrete are independent of the water-cement ratio in the concrete mix.
Which of these statements are correct?
A
1 and 4 only
B
1 and 3 only
C
2 and 3 only
D
1, 2 and 3
Question 121Single Answer
According to the Indian Standard Specifications, concrete should be cured under a humidity of
A
90%
B
80%
C
60%
D
70%
Question 122Single Answer
Consider the following statements:In a typical compression test with a cylindrical concrete specimen, failure is initiated by
1.Crushing in compression
2.Inclined shear failure
3.Longitudinal tensile cracks
Which of these statements are correct?
A
1 only
B
2 only
C
3 only
D
1, 2 and 3
Question 123Single Answer
If one intends to obtain the best workability of concrete, the preferred shape of aggregate is
A
Round
B
Annular
C
Triangular
D
Flinty
Question 124Single Answer
Consider the following statements as regards rheology of concrete:
1.It deals with strength of concrete.
2.It deals with deformation in concrete.
3.It is the study of deformation and flow of concrete.
4.It deals with rate of shear and shear stress in concrete.
Which of these statements are correct?
A
1, 2, 3 and 4
B
3 and 4 only
C
2 and 3 only
D
1 and 2 only
Question 125Single Answer
Consider the following for durability of well-graded concrete:
1.The environment
2.Cover to embedded reinforcement
3.Shape and size of concrete member
Which of these are correct?
A
1 and 2 only
B
1 and 3 only
C
2 and 3 only
D
1, 2 and 3
Question 126Single Answer
Consider the common methods related to testing of concrete:
1.Consistency
2.Compacting factor
3.Vee-Bee
4.Setting time
5.Slump
Which of these methods refer to measuring workability ofconcrete?
A
1, 2 and 3
B
1, 2 and 5
C
2, 3 and 4
D
2, 3 and 5
Question 127Single Answer
Gypsum is added into the raw materials during manufacture of cement so that the final product exhibits
A
Retarded initial setting time
B
Improved mouldability for cornices, etc
C
Increases compressive strength
D
Augmented bond strength
Question 128Single Answer
Consider the following constituents of a high performance concrete (HPC):
1.Cement
2.Fine aggregate
3.Coarse aggregate
4.Water
5.Mineral admixture
6.Chemical admixture
Which of these constituentsare relevant for HPC?
A
1, 2, 3, 4, 5 and 6
B
1, 2, 3, 4 and 5 only
C
2, 3, 4, 5 and 6 only
D
1, 2, 3, 5 and 6 only
Question 129Single Answer
A specimen is subjected to a pure shear stress regime of intensity.The resulting tensile and compressive stresses, which occur on planes inclined at 45° to the direction of the shear stresses, would be
A
T
B
T
2
C
T2
D
T3
Question 130Single Answer
For a given elastic material, the Elastic modulus E is 210 GPa and its Poisson’s ratio is 0.27. What is the approximate value if its modulus of Rigidity ?
A
105 GPa
B
83 GPa
C
159 GPa
D
165 GPa
Question 131Single Answer
Which of the following is not a basic type of strain ?
A
Compressive strain
B
Shear strain
C
Area strain
D
Volume strain
Question 132Single Answer
Young's Modulus of elasticity is
A
Tensile stress / Tensile strain
B
Shear stress / Shear strain
C
Tensile stress / Shear strain
D
Shear stress / Tensile strain
Question 133Single Answer
Which of the following stresses is measured on inclined surface in Mohr’s Circle Method ?
A
Principal stress
B
Normal stress
C
Tangential stress
D
Maximum stress
Question 134Single Answer
Hooke's law is applicable within
A
Elastic limit
B
Plastic limit
C
Fracture point
D
Ultimate strength
Question 135Single Answer
Lead, as a material used in construction, has E = 15 GPa and K = 50 GPa. What is its Poisson’s ratio?
A
0.225
B
0.30
C
0.40
D
0.45
Question 136Single Answer
Crushing strength of good building stone should be more than:
A
500 kg/cm2
B
1000 kg/cm2
C
1400 kg/cm2
D
2000 kg/cm2
Question 137Single Answer
Two planks each of 50 mm × 50 mm section are glued together along the length to form as section 50 mm × 100 mm; and used as a beam. If the shear force at the section is 1000 N, what is the maximum shear stress on the glue?
A
0.15 MPa
B
0.3MPa
C
0.6MPa
D
2.4MPa
Question 138Single Answer
The probability distribution taken to represent the completion time in PERT analysis is
A
Gamma distribution
B
Normal distribution
C
Beta distribution
D
Log-normal distribution
Question 139Single Answer
The state of stress at a point in 2-D stress system is characterized by direct stresses of 40 MPa compressive and 80 MPa tensile, on mutually perpendicular planes. Shear stress is absent on these planes. The maximum shear stress sat this point (along a duly identified plane) is
A
20 MPa
B
40MPa
C
60MPa
D
80MPa
Question 140Single Answer
An electrical resistance strain rosette indicates strain of -400, +800 and +500 along the x,y and 45° axes. What is the shearing ratio yxy?
A
100
B
800
C
600
D
-200
Question 141Single Answer
In a diagonal scale only
A
Units can be shown
B
Units, tenths can be shown
C
Units, tenths, hundredths can be shown
D
Units, tenths, hundredths and thousandths can be shown
Question 142Single Answer
A cylindrical pressure vessel is 1200 mm in diameter. It is made of rolled mild steel plate. The vessel is subjected to an internal pressure of 2 N/mm2. If the material yields at 200 N/mm2, what should be the minimum safe thickness of the plate, based on Maximum Principle Stress Theory?
A
18 mm
B
15 mm
C
12 mm
D
9 mm
Question 143Single Answer
The constituent compound in Portland cement which reacts immediately with water, and also sets earliest, is
A
Tricalcium silicate
B
Dicalcium silicate
C
Tricalcium aluminate
D
Tetracalcium aluminoferrite
Question 144Single Answer
A simply subjected beam of length 4 m is subjected to a uniformly distributed load of 2 kN/m. What is the maximum shear stress is the cross-section is rectangular, 100 mm wide and 200 mm deep?
A
0.2 N/mm2
B
0.1 N/mm2
C
0.4 N/mm2
D
0.3 N/mm2
Question 145Single Answer
A mild steel structural section is an unsymmetrical I-section, with the greater width at the top and the smaller width at the bottom. The overall depth of the beam is 300 mm, and the flange stresses at the top and the bottom of the beam are 150 N/mm2and 50 N/mm2 respectively. What is the height of the neutral axis of the beam from its bottom?
A
125 mm
B
100 mm
C
75 mm
D
50 mm
Question 146Single Answer
The surveying used to determine additional details such as boundaries of fields, is called
A
City surveying
B
Location surveying
C
Cadastral surveying
D
Topographical surveying
Question 147Single Answer
A circular shaft of diameter ‘D’ is made of a material for which the Young’s modulus of elasticity is ‘E’ and Poisson’s ratio is ‘v’. the ratio of flexural rigidity to torsional rigidity for the shaft is
A
4(1+v)
B
1.5(1-2v)
C
(1+v)
D
0.25(1+v)
Question 148Single Answer
A closely coiled helical spring of round steel wire 5mm in diameter having 12 complete coils of 50 mm mean diameter is subjected to an axial load of 100 N. Modulus of rigidity of the spring is 80kn/mm2. What is the deflection of the spring?
A
12 mm
B
24 mm
C
36 mm
D
48 mm
Question 149Single Answer
What is the shear stress at the neutral axis in a beam of isosceles triangular section with a base of 40 mm and height 20 mm subjected to a shear force of 2 kN?
A
3 MPa
B
6MPa
C
10MPa
D
20MPa
Question 150Single Answer
A beam of square cross-section is placed such that its neutral axis coincides with its diagonal, and it is subjected to a shear force F. What is the ratio of the maximum shear stress to the shear stress at the neutral axis?