📚 Exam by Category
▾
Objective Questions

Latest GATE Production and Industrial Engineering Exam Question (Objective Questions), MCQ in English

Subjects : Production & Industrial Engineering

Question Bank GATE Production & Industrial Engineering Exam - English
Back to Exam

Production & Industrial Engineering

Question 1Single Answer
“The dress ...........her so well that they all immediately ..........her on her appearance.”  The words that best fill the blanks in the above sentence are
  1. A
    complemented, complemented
  2. B
    complimented, complemented
  3. C
    complimented, complimented
  4. D
    complemented, complimented
Question 2Single Answer
though shaken by false allegations of wrong doing, remained .............   The word that best fills the blank in the above sentence is
  1. A
    undiminished
  2. B
    damaged
  3. C
    illegal
  4. D
    uncertain
Question 3Single Answer
Find the missing group of letters in the following series :
BC, FGH, LMNO,...........
  1. A
    UVWXY
  2. B
    TUVWX
  3. C
    STUVW
  4. D
    RSTUV
Question 4Single Answer
The perimeters of a circle, a square and an equilateral triangle are equal. Which one of the following statements is true?
  1. A
    The circle has the largest area.
  2. B
    The square has the largest area,
  3. C
    The equilateral triangle has the largest area.
  4. D
    All the three shapes have the same area.
Question 5Single Answer
he value of the expression  is ...........
  1. A
    –1 
  2. B
    0
  3. C
    1 
  4. D
    3
Question 6Single Answer
Forty students watched films A, B and C over a week. Each student watched either only one film or all three. Thirteen students watched film A, sixteen students watched film B and nineteen students watched film C. How many students watched all three films?
  1. A
    0
  2. B
    2
  3. C
    4 
  4. D
    8
Question 7Single Answer
A wire would enclose an area of 1936 m2, if it is bent into a square. The ware is cut into two pieces. The longer piece is thrice as long as the shorter piece. The long and the short pieces are bent into a square and a circle, respectively. Which of the following choices is closest to the sum of the areas enclosed by the two pieces in square meters?
  1. A
    1096
  2. B
    1111
  3. C
    1243
  4. D
    2486
Question 8Single Answer
A contract is to be completed in 52 days and 125 identical robots were employed, each operational for 7 hours a day. After 39 days, five-seventh of the work was completed. How many additional robots would be required to complete the work on time, if each robot is now operational for 8 hours a day?
  1. A
    7 
  2. B
    89
  3. C
    146 
  4. D
    175
Question 9Single Answer
A house has a number which needs to be identified. The following three statements are given that can help in identifying the house number.
i. If the house number is a multiple of 3, then it is a number from 50 to 59.
ii. If the house number is NOT a multiple of 4, then it is a number from 60 to 69.
iii. If the house number is NOT a multiple of 6. then it is a number from 70 to 79,
What is the house number?
  1. A
    54
  2. B
    65
  3. C
    66
  4. D
    76
Question 10Single Answer
An unbiased coin is tossed six times in a row and four different such trials are conducted.  One trial implies six tosses of the coin. If H stands for head and T stands for tail, the following are the observations from the four trials:
(1) HTHTHT (2) TTHHHT
(3) HTTHHT (4) HHHT .... ....
Which statement describing the last two coin tosses of the fourth trial has the highest probability of being correct?
  1. A
    Two T will occur.
  2. B
    One H and one T will occur.
  3. C
    Two H will occur.
  4. D
    One H will be followed by one T.
Question 11Single Answer
Vector triple product a × (b × c) of three vectors a, b and c is given by
  1. A
    (a · c)b – (a · b)c
  2. B
    (b · c)a – (a · c)b
  3. C
    (a · b)c – (a · c)b
  4. D
    (b · c)a – (a · b)c
Question 12Single Answer
A real-valued function y of real variable is such that y = 5 |x|. At x = 0, the function is
  1. A
    discontinuous but differentiable
  2. B
    both continuous and differentiable
  3. C
    discontinuous and not differentiable
  4. D
    continuous but not differentiable
Question 13Single Answer
Considering the coordinate system shown in the figure, a force of magnitude 10 kN has  x-component of –6 kN. Possible y-component (s) of the force is/are
  1. A
    + 8 kN only
  2. B
    + 5 kN only
  3. C
    + 8 kN and –8 kN
  4. D
    + 5 kN and –5 kN
Question 14Single Answer
When austenite decomposes upon cooling into two phases—ferrite and cementite, the reaction is called
  1. A
    Eutectic
  2. B
    Eutectoid
  3. C
    Peritectic 
  4. D
    Peritectoid
Question 15Single Answer
Match the geometric tolerances with their correct symbols : 

(Circularity)
  1. A
    P - 1, Q - 3, R - 4, S - 2
  2. B
    P - 3, Q - 1, R - 4, S - 2
  3. C
    P - 3, Q - 1. R - 2, S - 4
  4. D
    P - 3, Q - 2, R - 1, S - 4
Question 16Single Answer
Which one of the following instruments makes use of the principle of interference of light?
  1. A
    Optical flat
  2. B
    Auto-collimator
  3. C
    Optical projector
  4. D
    Coordinate measuring machine
Question 17Single Answer
In ASME process chart, the symbol ˆ represents
  1. A
    operation
  2. B
    inspection
  3. C
    delay
  4. D
    transport
Question 18Single Answer
Which one of the following is the most appropriate control chart for measuring the variability of individual readings within a sample?
  1. A
    X-Chart
  2. B
    R-Chart
  3. C
    P-Chart 
  4. D
    C-Chart
Question 19Single Answer
The machines and auxiliary facilities are located according to processing sequence of the product (produced in very large quantities) in
  1. A
    Process Layout
  2. B
    Fixed Position Layout
  3. C
    Product Layout 
  4. D
    Cellular Layout
Question 20Single Answer
Which one of the following defects is NOT associated with the casting process?
  1. A
    Hot tear
  2. B
    Porosity
  3. C
    Blister
  4. D
    Central burst
Question 21Single Answer
In an oxy-acetylene gas welding process, oxygen and acetylene are mixed in a ratio of 1.5 : 1 (by volume). The flame is
  1. A
    neutral 
  2. B
    carburizing
  3. C
    reducing 
  4. D
    oxidizing
Question 22Single Answer
Each of three firms P, Q and R manufactures 100 lakhs components. The number of defective components produced by P, Q and R are 30, 42 and 47, respectively. The firm(s) in conformance with Six Sigma standard is/are
  1. A
    only P
  2. B
    P and Q
  3. C
    P, Q and R 
  4. D
    Q and R
Question 23Single Answer
To make holes of 0.5 mm diameter and 30 mm depth in a mild steel component, the most suitable process is
  1. A
    chemical machining
  2. B
    electrochemical machining
  3. C
    abrasive jet machining
  4. D
    plasma arc machining
Question 24Single Answer
Which one of the following processes is NOT used for producing powders?
  1. A
    Atomization  
  2. B
    Ball milling
  3. C
    Sintering 
  4. D
    Electrolysis
Question 25Single Answer
The process in which molten thermoplastic is forced between rolls to produce thin sheets is called
  1. A
    blow moulding
  2. B
    compression moulding
  3. C
    calendering 
  4. D
    extrusion
Question 26Single Answer
The diagonal elements of a 3-by-3 matrix are –10, 5 and 0, respectively. If two of its eigenvalues are –15 each, the third eigenvalue is .........
  1. A
    24.5 to 25.5 
  2. B
    25.5 to 25.5
  3. C
    24.5 to 25.4 
  4. D
    24.4 to 25.5
Question 27Single Answer
Weights (in kg) of six products are 3, 7, 6, 2, 3 and 4. The median weight (in kg, up to one decimal place) is ..........
  1. A
    3.49 to 3.50
  2. B
    3.49 to 3.52
  3. C
    3.48 to 3.51
  4. D
    3.49 to 3.51
Question 28Single Answer
The probabilities of occurrence of events F and G are P(F) = 0.3 and P(G) = 0.4, respectively. The probability that both events occur simultaneously is P(F  G) = 0.2. The probability of occurrence of at least one event P(F G) is ..........
  1. A
    0.49 to 0.52
  2. B
    0.49 to 0.51
  3. C
    0.50 to 0.51
  4. D
    0.49 to 0.50
Question 29Single Answer
A flywheel in the form of a solid circular disc of radius 100 mm and uniform thickness has a mass of 10 kg. If it is rotating at a uniform angular velocity of 20 rad/s, the kinetic energy (in J) of the flywheel is .........
  1. A
    9.9 to 11.1 
  2. B
    9.8 to 10.1
  3. C
    9.9 to 10.1 
  4. D
    9.9 to 10.2
Question 30Single Answer
A cylindrical wooden block of length 50 cm is floating in water in such a way that its axis is vertical. The densities of wood and water are 800 kg/m3 and 1000 kg/m3, respectively. The submerged depth, i.e., depth of immersion (in cm) of the cylinder is ..............
  1. A
    39 to 41
  2. B
    39 to 42
  3. C
    38 to 41 
  4. D
    39 to 40
Question 31Single Answer
A machine consists of three components P, Q and R connected serially. The reliabilities of P, Q and R are 0.97, 0.86 and 0.93, respectively. To .increase the reliability of the machine, two additional stand-by units of Q are attached. The overall reliability (up to two decimal places) of the machine is............
  1. A
    0.88 to 0.90
  2. B
    0.88 to 0.92
  3. C
    0.90 to 0.91
  4. D
    0.88 to 0.91
Question 32Single Answer
The mean time between failures of a machine is 400 hour. If the availability of the machine is 80%, the mean time to repair (in hour) is ..........
  1. A
    79 to 81 
  2. B
    79 to 80
  3. C
    80 to 81
  4. D
    79 to 82
Question 33Single Answer
Processing times on a single machine for 3 jobs are given below. All the jobs are available at time t = 0.
The mean flow time (in minute) as per the shortest processing time (SPT) sequence is ..........
  1. A
    11.8 to 11.2
  2. B
    11.0 to 12.2
  3. C
    11.8 to 12.2
  4. D
    11.8 to 12.1
Question 34Single Answer
In a two-pass wire drawing process, there is a 40% reduction in wire cross-sectional area in 1st pass and further 30% reduction in 2nd pass. The overall reduction (in percentage) is...........
  1. A
    57 to 50 
  2. B
    57 to 59
  3. C
    58 to 59
  4. D
    57 to 58
Question 35Single Answer
A double-start thread with a pitch of 2 mm is to be cut using a lathe machine. The pitch of the leadscrew of the lathe is 6 mm. The job rotates at 60 revolution per minute (RPM). The RPM of the leadscrew is ...............
  1. A
    39 to 41 
  2. B
    39 to 42
  3. C
    38 to 41 
  4. D
    39 to 40
Question 36Single Answer
Consider the analytic function f(z) = x2 – y2 + 12xy of the complex variable z = x + iy, where i = . The derivative f '(z) is 
  1. A
    2x + i2y
  2. B
    x2 + iy2
  3. C
    x + iy
  4. D
    2x – i2y
Question 37Single Answer
In order to evaluate the integrl  with Simpson’s 1/3rd rule, values of the function e:i are used at x = 0.0, 0.5 and 1.0. The absolute value of the error of numerical integration is 
  1. A
    0.000171
  2. B
    0.000440
  3. C
    0.000579
  4. D
    0.002718
Question 38Single Answer
A rigid link PQ of length 1.0 m is pinned at P. It rotates about P in a vertical plane with a uniform angular acceleration of 1.0 rad/s2. At an instant when the angular velocity of the link is 1.0 rad/s, the magnitude of total acceleration (in m/s2) of point Q relative to point P is
  1. A
    1.41
  2. B
    1.73
  3. C
    2
  4. D
    2.83
Question 39Single Answer
In a shaft-hole system, the dimensions with tolerances (in mm) are as follows
:
where both x and y are positive real numbers. Which one of the following will provide an interference fit?
  1. A
    x = 0.05, y = 0.040
  2. B
    x = 0.04, y = 0.035
  3. C
    x = 0.04, y = 0.032
  4. D
    x = 0.02, y = 0.035
Question 40Single Answer
A machine is procured at a price of Rs. 47000 with a 2-year warranty After two years, the annual maintenance cost (AMC) in Rs. is given by the following formula:
AMC = (i – 2) × 2000, for i > 2, 
where is the number of years elapsed since the machine was purchased. Neglect the scrap value of the machine, inflation, interest, etc. For minimizing the average cost, the machine should be replaced at the end of the year
  1. A
    2 
  2. B
    4
  3. C
    7 
  4. D
    10
Question 41Single Answer
In a service centre, cars arrive according to Poisson distribution with a mean of 2 cars per hour. The time for servicing a car is exponential with a mean of 15 minutes. The expected waiting time (in minute) in the queue is
  1. A
    10
  2. B
    15
  3. C
    25 
  4. D
    30
Question 42Single Answer
Actual and forecasted demands of a product are as follows :
The forecast error measured in terms of mean absolute deviation (MAD) and mean absolute percentage error (MAPE), respectively, are
  1. A
    13 and 7.84% 
  2. B
    13 and 9.85%
  3. C
    17 and 7.84% 
  4. D
    17 and 9.85%
Question 43Single Answer
In a mass production firm, measurements are carried out on 10000 pairs of shaft and hole. The mean diameters of the shaft and the hole are 37.53 mm and 37.59 mm, respectively. The corresponding standard deviations are 0.03 mm and 0.04 mm. The mean clearance and its standard deviation (both in mm), respectively, are
  1. A
    0.06 and 0.07 
  2. B
    0.06 and 0.06
  3. C
    0.06 and 0.05
  4. D
    0.07 and 0.01
Question 44Single Answer
A pressure die casting set-up was tested by injecting water (density 1000 kg/m3) at a pressure of 200 bar. Mould-filling time was found to be 0.05s. Afterwards, the actual casting is made by injecting the liquid metal (density 2000 kg/m3) at an injection pressure of 400 bar. Neglect all losses (friction, viscous-effect, etc.). The approximate mould-filling time (in s) is 
  1. A
    0.05 
  2. B
    0.075
  3. C
    0.1 
  4. D
    0.2
Question 45Single Answer
The value of the surface integral nds over the surface of the sphere x2 + y2 + z2 = 9, where n is the unit outward normal to the surface element ds, is ...............
  1. A
    676 to 681 
  2. B
    675 to 681
  3. C
    675 to 682 
  4. D
    675 to 680
Question 46Single Answer
Consider the differential equation
with initial conditions: 
at t = 0, y = 0 and  = 10
The value of (up to two decimal places) at = 1 is ........
  1. A
    4.53 to 4.51 
  2. B
    4.52 to 4.50
  3. C
    4.50 to 4.56 
  4. D
    4.52 to 4.56
Question 47Single Answer
One kg of air (that can be considered a calorically perfect gas with characteristic gas constant  R = 287 J/kg-K and specific heat ratio y = 1.4) undergoes a constant-volume process from an initial static pressure of 1 bar to a final static pressure of 4 bar. The increase in entropy (in J/kg-K) of air is............
  1. A
    990 to 1000 
  2. B
    990 to 100
  3. C
    990 to 10 
  4. D
    99 to 1000
Question 48Single Answer
If u = 2(x2 – y2) and v = –axy represent the x - and y - components of the two-dimensional velocity field of an incompressible flow, the value of the constant a is ............
  1. A
    3.9 to 4.2
  2. B
    3.0 to 4.1
  3. C
    3.9 to 4.1
  4. D
    3.9 to 41
Question 49Single Answer
A spherical pressure vessel (made of mild steel) of internal diameter 500 mm and thickness 10 mm is subjected to an internal gauge pressure of 4000 kPa. If the yield stress of mild steel is 200 MPa, the factor of safety (up to one decimal place) is ..........
  1. A
    3.5 to 4.1
  2. B
    3.6 to 4.4
  3. C
    3.5 to 4.4 
  4. D
    3.6 to 4.2
Question 50Single Answer
A square cross-section wooden column of length 3140 mm is pinned at both ends. For the wood, Young’s modulus of elasticity is 12 GPa and allowable compressive stress is 12 MPa.  The column needs to support an axial compressive load of200 kN. Using a factor of safety of 2.0 in the computation of Euler’s buckling load, the minimum cross-sectional area (in mm2) of the column is..........
  1. A
    19800 to 20200
  2. B
    1980 to 202000
  3. C
    19800 to 202000
  4. D
    1980 to 2020
Important Questions Package

GATE Production and Industrial Engineering Exam Online Question Bank Package

Buy GATE Production and Industrial Engineering Important Questions, MCQ, question answer in Hindi & English. It will help you to score high marks in GATE Production and Industrial Engineering question bank 2026 in Online, PDF & Print study material.

+ Free Monthly Current Affairs, GK & more PDF Download
Sr.Package NameAmount
1.GATE Production & Industrial Engineering Engineering Exam (Only MCQ ) - English
Description : 1000 Question With Answer
₹101 [₹500]
2.GATE Production & Industrial Engineering Engineering Exam (Only MCQ ) - English
Description : 2000 Question With Answer
₹151 [₹500]
3.GATE Production & Industrial Engineering Engineering Exam (Only MCQ ) - English
Description : 3000 Question With Answer
₹181 [₹500]
4.GATE Production & Industrial Engineering Engineering Exam (Only MCQ ) - English
Description : 4000 Question With Answer
₹210 [₹500]
5.GATE Production & Industrial Engineering Engineering Exam (Only MCQ ) - English
Description : 1000 Question & Answer Download in PDF (Send by Email)
₹151 [₹550]
6.GATE Production & Industrial Engineering Engineering Exam (Only MCQ ) Question Bank Book - English
Description : 1000 Question with Answer (Printed Material)
₹390 [₹650]
Back to Exam
Question for GATE Production & Industrial Engineering 2027 - Quiz / Questions / MCQ - Toppersexam