📚 Exam by Category
▾
Objective Questions

Latest GATE Mechanical Engineering Exam Question (Objective Questions), MCQ in English

Subjects : General Aptitude, Engineering Mathematics, Mechanical Engineering

Question Bank GATE Mechanical Engineering Exam (Only MCQ) - English
Back to Exam

General Aptitude

Question 1Single Answer
Inhaling the smoke from a burning _____ could _____ you quickly.
  1. A
    tire/tier
  2. B
    tire/tyre
  3. C
    tyre/tire
  4. D
    tyre/tier
Question 2Single Answer
Rice, a versatile and inexpensive source of carbohydrate, is a critical component of diet worldwide. Climate change, causing extreme weather, poses a threat to sustained availability of rice. Scientists are working on developing Green Super Rice (GSR), which is resilient under extreme weather conditions yet gives higher yields sustainably.
Which one of the following is the CORRECT logical inference based on the information given in the above passage ?
  1. A
    GSR is an alternative to regular rice, but it grows only in an extreme weather
  2. B
    GSR be used in future in response to adverse effects of climate change
  3. C
    GSR grows in an extreme weather, but the quantity of produce is lesser than regular rice
  4. D
    Regular rice will continue to provide good yields even in extreme weather
Question 3Single Answer
The cost price of 20 articles is the same as the selling price of x articles. If the profit is 25%, then the value of x is :
  1. A
    15
  2. B
    16
  3. C
    18
  4. D
    25
Question 4Single Answer
Pipes P and Q can fill a storage tank full of water in 10 and 6 minutes, respectively. Pipe R draws the water out from the storage tank at a rate of 34 litres per minute. P, Q and R operate at a constant rate. If it takes one hour to completely empty a full storage tank with all the pipes operating simultaneously, what is the capacity of the storage tank (in litres) ? 
  1. A
    26.8 
  2. B
    60.0 
  3. C
    120.0
  4. D
    127.5
Question 5Single Answer
Choose the grammatically correct sentence?
  1. A
    Neither of the robots are functioning properly
  2. B
    Neither robots is functioning properly
  3. C
    Neither of the robot are functioning properly
  4. D
    Neither of the robots is functioning properly

Engineering Mathematics

Question 6Single Answer
Consider the following expression :
where z, y, and t are variables, and   is a complex number. The partial differential equation derived from the above expression is
  1. A
  2. B
  3. C
  4. D
Question 7Single Answer
For the equation
the correct description is
  1. A
    an ordinary differential equation of order 3 and degree 2 
  2. B
    an ordinary differential equation of order 3 and degree 3 
  3. C
    an ordinary differential equation of order 2 and degree 3 
  4. D
    an ordinary differential equation of order 3 and degree 
Question 8Single Answer
The value of (1 + i)12, where  , is.
  1. A
    – 64 i 
  2. B
    64 i
  3. C
    64 
  4. D
    – 64
Question 9Single Answer
If (A=\begin{bmatrix}1&2\3&4\end{bmatrix}), what is (\det(A))?
  1. A
    2
  2. B
    (-2)
  3. C
    5
  4. D
    10
Question 10Single Answer
If (A) is a (3\times3) matrix with (\det(A)=5), what is (\det(2A))?
  1. A
    10
  2. B
    40
  3. C
    20
  4. D
    80

Mechanical Engineering

Question 11Single Answer
For a rigid body in planar static equilibrium, which set of equations must be satisfied?
  1. A
    ΣM = 0 only
  2. B
    ΣFx = 0 only
  3. C
    ΣFx = ΣFy
  4. D
    ΣFx = 0, ΣFy = 0 and ΣM = 0
Question 12Single Answer
A two-force member in equilibrium carries forces that are?
  1. A
    equal and concurrent but non-collinear
  2. B
    unequal and parallel
  3. C
    equal and perpendicular
  4. D
    equal, opposite and collinear
Question 13Single Answer
The method of joints is primarily used to determine?
  1. A
    beam deflection
  2. B
    member forces in a truss
  3. C
    fluid pressure
  4. D
    gear tooth stress
Question 14Single Answer
In an ideal pin-jointed truss, external loads are assumed to act at?
  1. A
    midpoints of members
  2. B
    joints
  3. C
    centroids of members
  4. D
    random points on members
Question 15Single Answer
For pure translation of a rigid body, the angular velocity is?
  1. A
    equal to linear velocity
  2. B
    zero
  3. C
    infinite
  4. D
    constant and nonzero
Question 16Single Answer
The instantaneous center of zero velocity in plane motion is a point where?
  1. A
    acceleration is always zero
  2. B
    angular velocity is zero
  3. C
    force is zero
  4. D
    velocity is zero at that instant
Question 17Single Answer
Linear impulse is equal to the change in?
  1. A
    potential energy
  2. B
    angular displacement
  3. C
    linear momentum
  4. D
    mass
Question 18Single Answer
Angular impulse about a point equals the change in?
  1. A
    angular momentum about that point
  2. B
    mass moment of area
  3. C
    linear displacement
  4. D
    strain energy only
Question 19Single Answer
Work-energy principle relates net work done to change in?
  1. A
    kinetic energy
  2. B
    Poisson's ratio
  3. C
    mass
  4. D
    temperature
Question 20Single Answer
D'Alembert's principle converts a dynamics problem into an equivalent problem of?
  1. A
    elastic instability only
  2. B
    heat balance
  3. C
    mass diffusion
  4. D
    static equilibrium by adding inertia forces
Question 21Single Answer
The kinetic energy of a rotating rigid body about a fixed axis is?
  1. A
    1/2 mω²
  2. B
    I/ω
  3. C
    Iω
  4. D
    1/2 Iω²
Question 22Single Answer
Normal stress is defined as?
  1. A
    shear force divided by length
  2. B
    strain divided by modulus
  3. C
    normal force divided by area
  4. D
    moment divided by volume
Question 23Single Answer
Within the elastic range, Hooke's law states that stress is proportional to?
  1. A
    strain
  2. B
    density
  3. C
    area
  4. D
    temperature only
Question 24Single Answer
Poisson's ratio is the ratio of?
  1. A
    Young's modulus to density
  2. B
    lateral strain to longitudinal strain in magnitude
  3. C
    shear stress to normal stress
  4. D
    volumetric stress to pressure
Question 25Single Answer
The relation between Young's modulus E, shear modulus G and Poisson's ratio ν is?
  1. A
    E = 2G(1+ν)
  2. B
    E = G(1+ν)
  3. C
    E = 3G(1−ν)
  4. D
    E = G/(1+ν)
Question 26Single Answer
For an isotropic material, the relation between E, bulk modulus K and ν is?
  1. A
    E = 2K(1+ν)
  2. B
    E = Kν
  3. C
    E = 3K(1+2ν)
  4. D
    E = 3K(1−2ν)
Question 27Single Answer
On a principal plane, the shear stress is?
  1. A
    always tensile
  2. B
    zero
  3. C
    equal to normal stress
  4. D
    maximum
Question 28Single Answer
Maximum in-plane shear stress equals?
  1. A
    half the difference between principal stresses
  2. B
    principal stress product
  3. C
    twice the average stress
  4. D
    sum of principal stresses
Question 29Single Answer
For a thin cylindrical pressure vessel, hoop stress is?
  1. A
    4pt/d
  2. B
    pd/(2t)
  3. C
    pt/(2d)
  4. D
    pd/(4t)
Question 30Single Answer
For a thin cylindrical pressure vessel, longitudinal stress is?
  1. A
    2pd/t
  2. B
    pd/(2t)
  3. C
    pd/(4t)
  4. D
    pt/d
Question 31Single Answer
A particle of mass 8 kg moves at 4 m/s. Its kinetic energy is?
  1. A
    32 J
  2. B
    64 J
  3. C
    32 J
  4. D
    128 J
Question 32Single Answer
The slope of the shear-force diagram at a section equals?
  1. A
    negative load intensity under the usual sign convention
  2. B
    Young's modulus
  3. C
    bending moment
  4. D
    deflection
Question 33Single Answer
In pure bending of a homogeneous beam, normal stress varies?
  1. A
    quadratically with depth
  2. B
    linearly with distance from the neutral axis
  3. C
    inversely with depth
  4. D
    uniformly over depth
Question 34Single Answer
The flexure formula is?
  1. A
    M/I = σ/y = E/R
  2. B
    T/J = σ/y
  3. C
    P/A = E/R
  4. D
    M/Z = τ/R
Question 35Single Answer
The polar moment of inertia of a solid circular shaft of diameter d is?
  1. A
    πd²/4
  2. B
    πd⁴/64
  3. C
    πd³/16
  4. D
    πd⁴/32
Question 36Single Answer
Euler buckling load for a pin-ended column is?
  1. A
    πEI/L
  2. B
    π²EI/L²
  3. C
    π²EA/L
  4. D
    2π²EI/L²
Question 37Single Answer
Slenderness ratio of a column is?
  1. A
    area divided by length
  2. B
    effective length divided by radius of gyration
  3. C
    length divided by area
  4. D
    radius of gyration divided by length
Question 38Single Answer
Strain energy per unit volume in uniaxial linear elasticity is?
  1. A
    σ/E
  2. B
    2σ²/E
  3. C
    E/(2σ²)
  4. D
    σ²/(2E)
Question 39Single Answer
A fully restrained bar subjected to temperature rise develops?
  1. A
    compressive thermal stress
  2. B
    tensile thermal stress
  3. C
    no stress under any condition
  4. D
    pure shear stress
Question 40Single Answer
Gauge factor of a metallic strain gauge is approximately the ratio of?
  1. A
    strain to resistance
  2. B
    stress to strain
  3. C
    fractional resistance change to strain
  4. D
    voltage to current
Question 41Single Answer
A three-element rectangular strain rosette is commonly used to determine?
  1. A
    fluid viscosity
  2. B
    hardness number only
  3. C
    gear module
  4. D
    principal strains and their directions
Question 42Single Answer
A universal testing machine is commonly used for?
  1. A
    only creep tests
  2. B
    only hardness tests
  3. C
    tensile and compressive tests
  4. D
    only impact tests
Question 43Single Answer
Brinell hardness testing uses an indenter that is typically?
  1. A
    a knife edge
  2. B
    a hard spherical ball
  3. C
    a sharp diamond cone only
  4. D
    a flat punch
Question 44Single Answer
Grashof's law for a four-bar chain involves the sum of the shortest and longest links being?
  1. A
    less than or equal to the sum of the other two links for at least one link to rotate fully
  2. B
    always greater than the other two
  3. C
    unrelated to link lengths
  4. D
    equal to the product of the other two
Question 45Single Answer
The Coriolis acceleration component appears when a point moves?
  1. A
    along a rotating link
  2. B
    only on a fixed link
  3. C
    only in pure translation
  4. D
    only under static loading
Question 46Single Answer
The fundamental law of gearing requires the common normal at contact to pass through?
  1. A
    the dedendum circle
  2. B
    any point on base circle
  3. C
    the pitch point
  4. D
    the addendum circle center
Question 47Single Answer
For involute gears, the pressure angle during engagement is?
  1. A
    constant
  2. B
    zero
  3. C
    continuously decreasing
  4. D
    continuously increasing
Question 48Single Answer
Interference in involute gears is associated with contact below the?
  1. A
    root circle of both gears simultaneously
  2. B
    addendum circle only
  3. C
    pitch circle only
  4. D
    base circle of one gear
Question 49Single Answer
In a simple gear train, an idler gear changes?
  1. A
    pressure angle
  2. B
    module
  3. C
    direction of rotation but not the magnitude of velocity ratio
  4. D
    velocity ratio magnitude only
Question 50Single Answer
A reverted gear train has?
  1. A
    only internal gears
  2. B
    input and output shafts coaxial
  3. C
    only bevel gears
  4. D
    all shafts parallel but never coaxial
Important Questions Package

GATE Mechanical Engineering Exam Online Question Bank Package

Buy GATE Mechanical Engineering Important Questions, MCQ, question answer in Hindi & English. It will help you to score high marks in GATE Mechanical Engineering question bank 2026 in Online, PDF & Print study material.

+ Free Monthly Current Affairs, GK & more PDF Download
Sr.Package NameAmount
1.GATE Mechanical Engineering Exam (Only MCQ) - English
Description : 1000 Question With Answer
₹101 [₹500]
2.GATE Mechanical Engineering Exam (Only MCQ) - English
Description : 2000 Question With Answer
₹151 [₹500]
3.GATE Mechanical Engineering Exam (Only MCQ) - English
Description : 3000 Question With Answer
₹181 [₹500]
4.GATE Mechanical Engineering Exam (Only MCQ) Question Bank Book - English
Description : 1000 Question with Answer (Printed Material)
₹390 [₹650]
5.GATE Mechanical Engineering Exam (Only MCQ) - English
Description : 1000 Question & Answer Download in PDF (Send by Email)
₹151 [₹550]
6.GATE Mechanical Engineering Exam (Only MCQ) - English (OLD)
Description : 800 Question With Answer
₹181 [₹500]
Back to Exam