Assuming both the voltage sources are in phase, the value of R for which maximum power is transferred from circuit A to circuit B is
A
0.8 Ω
B
1.4 Ω
C
2 Ω
D
2.8 Ω
Question 2Single Answer
For the intrinsic gallium-arsenide, the conductivity at room temperature 25°C is 10-6 (ohm-m)-1, the electron and hole nobilities are 0.85 m2/V-s and 0.04 m2/V-s respectively. What is the intrinsic carrier concentration at the room temperature?
A
7.0 × 1012 m-3
B
7.0 × 10-12 m-3
C
7.0 × 10-12 m3
D
7.0 × 1012 m3
Question 3Single Answer
The resistivity of intrinsic germanium at 30°C is 0.46 –m. What is the intrinsic carrier density at 30°C if the electron mobility is 0.38 m2/V-s and the hole mobility is 0.18 m2/V-s?
A
9.2 × 105/m3
B
2.77 × 103/m3
C
2.43 × 1019/m3
D
8.9 × 1012/m3
Question 4Single Answer
Heat conduction in a semiconductor takes place
A
By the mobility of the carriers
B
Due to energy gap between conduction band and valency band
C
By the holes and thermal vibrations of atoms
D
By the electrons and thermal vibrations of atoms
Question 5Single Answer
Brewster angle is the angle when a wave is incident on the surface of a perfect dielectric at which there is no reflected wave and the incident wave is
A
Parallel polarized
B
Perpendicularly polarized
C
Normally polarized
D
None of the above
Question 6Single Answer
An electrical breakdown of a p-n junction occurs if
A
Forward voltage increases up to the rating
B
Reverse voltage increases beyond the rating
C
Forward voltage decreases below the rating
D
Reverse voltage decreases below the rating
Question 7Single Answer
The chief deterrent to the widespread application of superconducting materials is
A
Very difficult to form, machine or case
B
The difficult in attaining and maintaining extremely low temperature
C
The poor strength-to-weight ratio
D
The lower oxidation rate at elevated temperatures
Question 8Single Answer
Which one of the following properties is not observed in the carbon nanotubes ?
A
High stiffness and strengths
B
Low densities
C
Unusual electrical property
D
Non-ductile
Question 9Single Answer
The evidence for the importance of electron-phonon interaction in super-conductors comes from
A
Meissner effect
B
Josephson effect
C
Isotope effect
D
x quantization experiments
Question 10Single Answer
Which one of the following materials is used for cable insulation ?
A
Phenol formaldehyde
B
Polytetrafluoroethylene
C
Polyvinyl chloride
D
Acrylonitrile butadiene styrene
Question 11Single Answer
For high speed reading and storing of information in a computer, the material used is
A
Ferrite
B
Piezoelectric
C
Pyroelectric
D
Ferromagnetic above 768°C
Question 12Single Answer
The temperature above which an anti-ferromagnetic material becomes paramagnetic is called
A
Peak temperature
B
Neel temperatur
C
Critical temperature
D
Weiss temperature
Question 13Single Answer
Which effect is the converse of Peltier effect ?
A
Seeback effect
B
Thomson effect
C
Hall effect
D
Joule effect
Question 14Single Answer
Magnetic materials which may be readily magnetized in either direction are
A
Soft magnetic materials
B
Hard magnetic materials
C
High eddy current loss materials
D
High hysteresis loss materials
Question 15Single Answer
Consider the following statements regarding a ferromagnetic material:
1.Below the ferromagnetic Curie temperature, the ferromagnetic materials exhibit hysteresis effect.
2.The coercive force is the filed required to reduce the flux density to zero.
Which of the above statements is/are correct?
A
Both 1 and 2
B
Neither 1 nor 2
C
1 only
D
2 only
Question 16Single Answer
The impact ionization phenomenon in semiconductor may be viewed as the reverse process of
A
Radiative recombination
B
Auger recombination
C
Surface recombination
D
Shockley-Read-Hall recombination
Question 17Single Answer
Refractive index of a slice glass can be reduced by doping it with tiny amount of
A
GeO2
B
B2O3
C
P2O5x
D
Al2O3
Question 18Single Answer
If a diameter of a copper wire is increased by two times keeping its terminal voltage same, then the drift velocity will
A
Become twice
B
Become half
C
ecome four times
D
Remain unchanged
Question 19Single Answer
In an induction type energy meter, the steady speed attained by the rotating disc is
1.Proportional to the deflecting torque.
2.Proportional to the resistance of the path of eddy currents.
3.Inversely proportional to the effective readings of disc from its axis.
4.Inversely proportional to the square of brake magnetic flux.
Which of the above are correct?
A
1, 2 and 3 only
B
1, 2 and 4 only
C
2, 3 and 4 only
D
1, 2, 3 and 4
Question 20Single Answer
If ‘KCLFTSB’ stands for ‘best of luck’ and ‘SHSWDG’ stands for ‘good wishes’, which of the following indicates ‘ace the exam’?
A
MCHTX
B
MXHTC
C
XMHCT
D
XMHTC
Question 21Single Answer
Consider the following statements associated with the basic electrostatic properties of ideal conductors:
1.The resultant field inside is zero.
2.The net charge density in the interior is zero.
3.Any net charges reside on the surface.
4.The surface is always equipotential.
5.The field just outside is zero.
Which of the above statements are correct?
A
1, 2, 3 and 4
B
3, 4 and 5 only
C
1, 2 and 3 only
D
2 and 3 only
Question 22Single Answer
A semiconductor device made out of a material having very high temperature coefficient of resistance is
A
Transistor
B
Varistor
C
Thyristor
D
Thermistor
Question 23Single Answer
The electrical conductivity of a semiconductor increases with increase in temperature because
A
The carrier concentration increases
B
The mobility of carrier increases
C
Both carrier concentration and mobility increases
D
The band gap decreases
Question 24Single Answer
Which of the following are associated with soft superconductors?
1.Silsbee’s rule
2.Meissner effect
3.Faraday rotation
4.Curie-Weiss law
A
2, 3 and 4
B
1 and 3 only
C
1 and 2 only
D
2 and 3 only
Question 25Single Answer
In a two-channel oscilloscope operating in x-y mode, two in-phase 50 Hz sinusoidal waveforms of equal amplitude are fed to the two channels. What will be the resultant pattern on the screen?
A
An ellipse
B
A parabola
C
Straight line inclined at 45 with respect to x-axis
D
A circle
Question 26Single Answer
Materials, whose resistivity at very low temperature plunges from a finite value to zero and remains there upon further cooling, are known as
A
Ferromagnetic materials
B
High-energy hard magnetic materials
C
Superconductors
D
Ferromagnetic materials
Question 27Single Answer
In a superconductor, is the temperature is decreased below its critical temperature, the value of critical magnetic field will
A
Increase
B
Decrease
C
Not change
D
Increase or decrease depending on the superconductor material
Question 28Single Answer
The imaginary part of dielectric constant determines
A
Component of current which is in phase with the applied field
B
Component of energy absorbed per m3
C
Amount of applied field
D
Component of voltage which is in phase with the applied field
Question 29Single Answer
Direction:Each of the items consists of two statements, one labeled as the ‘Statement (I)’ and the other as ‘Statement (II)’. Examine these two statements carefully and select the answers to these items using the codes given below
A
Statement (I):Hard magnetic materials are used for making permanent magnets. Statement (II):
Hard magnetic materials have relatively small and narrow hysteresis loop.
B
Both Statement (I) and Statement (II) are individually true and Statement (II) is the correct explanation of Statement (I)
C
Both Statement (I) and Statement (II) are individually true and Statement (II) is NOT the correct explanation of Statement (I)
D
Statement (I) is true but Statement (II) is false
E
Statement (I) is false but Statement (II) is true
Question 30Single Answer
In 8085A microprocessor, the operation performed by the instruction LHLD 2100 H is
A
(H) ← 21 H, (L) ←00
B
(H) ← M (2100 H), (L) ←M(2101H)
C
(H) ← M (2100 H), (L) ←M(2100H)
D
(H) ← 00H, (L) ←21H
Question 31Single Answer
If the magnetic susceptibility of a specimen is small and positive, the specimen is
A
Diamagnetic
B
Paramagnetic
C
Ferromagnetic
D
Non-magnetic
Question 32Single Answer
Manganese ferrite is a 1 : 1 mixture of
A
Manganese nitride and iron oxide
B
Manganese oxide and iron nitride
C
Manganese nitride and iron sulphide
D
Manganese oxide and iron sulphide
Question 33Single Answer
When a ferromagnetic substance is magnetized, small changes in dimensions occur. Such a phenomenon is known as
A
Magnetic hysteresis
B
Magnetic expansion
C
Magnetostriction
D
Magneto-calorisation
Question 34Single Answer
In ferromagnetic , anti-ferromagnetic and ferromagnetic materials, the atomic thermal motions counteract the coupling forces between the adjacent atomic dipole moments, thereby causing
A
Some dipole misalignment regardless of whether an external field is present
B
Increase in dipole alignment regardless of whether an external field is present
C
No effect on dipole alignment
D
Atoms tend to de-randomize the direction of moments
Question 35Single Answer
The Hall effect voltage in intrinsic silicon
A
Is positive
B
Is zero
C
Is negative
D
Changes its sign based on application of magnetic field
Question 36Single Answer
Most outstanding property of indium antimonide is
A
A very wide range gap
B
High resistivity at room temperature
C
High carrier mobility
D
Very low conductivity at room temperature
Question 37Single Answer
Which of the following semiconducting compounds is used in photoconductive devices?
A
Caesium antimonide
B
Barium oxide
C
Lead sulphide
D
Zinc oxide
Question 38Single Answer
Consider the following transducers:
1.LVDT
2.Piezoelectric
3.Thermocouple
4.Photovoltaic cell
Which of the above are active transducers?
A
1, 2 and 3
B
1, 2 and 4
C
2 and 3 only
D
2, 3 and 4
Question 39Single Answer
Consider the following statements regarding magnetic materials:
1.A diamagnetic material has no permanent dipole
2.Paramagnetic material has anti-parallel orientation of equal moments with neighboring dipoles
3.Ferrimagnetic material has anti parallel orientation of unequal moments between neighboring dipoles
4.Anti-ferromagnetic material has negligible interaction between neighboring dipoles
Which of these statements are correct?
A
1 and 2
B
3 and 4
C
2 and 4
D
1 and 3
Question 40Single Answer
Consider the following statements regarding hysteresis loops of hard and soft magnetic materials:
1.Hysteresis loss of hard magnetic material will be less than that of soft material
2.Coercivity of hard materials will be greater than that of soft material
3.Retentivity of the two materials will always be equal
Which of these statements are correct?
A
1, 2 and 3
B
2 only
C
3 only
D
1 and 3 only
Question 41Single Answer
Loss-tangent in plane waves in lossy dielectrics will be
A
Proportional to the Y component of the magnetic field intensity (HY)
B
Inversely proportional to the Y component of the magnetic field intensity (HY)
C
Inversely proportional to the X component of the magnetic field intensity (HX)
D
proportional to the X component of the magnetic field intensity (HX)
Question 42Single Answer
Orientational polarization is
A
Inversely proportional to temperature and proportional to the square of the permanent dipole moment
B
proportional to temperature as well as to the square of the permanent dipole moment
C
proportional to temperature and inversely proportional to the square of the permanent dipole moment
D
Inversely proportional to temperature as well as to the square of the permanent dipole moment
Question 43Single Answer
Behavior of conductors, semiconductors and insulators is explained on the basis of
A
Atomic nature
B
Molecular structure
C
Energy band structure
D
All of the above
Question 44Single Answer
In general, for a superconductor, which of the following statements is true?
A
A superconductor is a perfect paramagnetic material with the magnetic susceptibility equals to positive unity
B
A superconductor is a perfect diamagnetic material with the magnetic susceptibility equals to negative one
C
A superconductor is a perfect ferromagnetic material with the magnetic susceptibility equals to positive one
D
A superconductor is a perfect piezoelectric material with the magnetic susceptibility equals to negative one
Question 45Single Answer
Ferro-electric materials have a
A
High dielectric constant which varies non linearly
B
Low dielectric constant and is non-linear
C
High dielectric constant which varies linearly
D
Low dielectric constant but linear
Question 46Single Answer
In the magnetic core the electromotive forces (emf) induced in accordance with Faraday’s law of electromagnetic induction give rise to
A
Eddy current
B
Excitation current
C
Armature current
D
Field current
Question 47Single Answer
Consider the following characterizing parameters of a material:
1.Magnetic permeability
2.Electron relaxation time 3.Electron effective mass
4.Energy band gap
In case of metals, increase in one of the above parameter decreases its conductivity, while increase in another increases the conductivity. There are respectively
A
1 and 3
B
3 and 2
C
4 and 3
D
1 and 2
Question 48Single Answer
Some magnetic materials may be classified on the basis of
1.Susceptibility
2.Saturation
3.Spin arrangement
4.Nature of hysteresis loop
5.Domain structure
6.Critical temperature above which it behaves as a paramagnetic material
Which of these can be used to distinguish between ferri and ferromagnetic materials?
A
1, 3 and 4 only
B
2, 3 and 6 only
C
3, 4 and 5 only
D
1, 2, 3, 4, 5 and 6
Question 49Single Answer
Magnetism is mainly due to only electron spin around their axis in case of
A
Diamagnetic materials
B
Paramagnetic materials
C
Ferromagnetic materials
D
Paramagnetic and Diamagnetic materials
Question 50Single Answer
For Paramagnetic materials, the relative permeability is
A
Less than unity but magnetic susceptibility is relatively small and positive
B
greater than unity and magnetic susceptibility is relatively small but positive
C
equal to unity and magnetic susceptibility is relatively large but positive
D
Less than unity but magnetic susceptibility is relatively large and positive
Important Questions Package
BPCL Apprentice Exam Online Question Bank Package
Buy BPCL Apprentice Important Questions, MCQ, question answer in Hindi & English. It will help you to score high marks in BPCL Apprentice question bank 2026 in Online, PDF & Print study material.
+ Free Monthly Current Affairs, GK & more PDF Download
Sr.
Package Name
Amount
1.
BPCL Apprentice Exam - English
Description : 1500 Question with Answer
₹181[₹500]
2.
BPCL Apprentice Exam - Hindi
Description : 1500 Question with Answer
₹181[₹500]
3.
BPCL Apprentice Exam Question Bank Book - English
Description : 1000 Question with Answer (Printed Material)
₹390[₹600]
4.
BPCL Apprentice Exam Question Bank Book - Hindi
Description : 1000 Question with Answer (Printed Material)
₹450[₹800]
Mechanical
Question 51Single Answer
A fin will be more effective when Bio number is
A
Greater than 1
B
Equal to 1
C
Between 1 and 3
4 4
D
Less than 1
Question 52Single Answer
A tank of length, breadth and height in the ratio of 2:1:2 is full of water. The ratio of hydrostatic force at the bottom to that at any larger vertical surface is
A
1
B
2
C
3
D
4
Question 53Single Answer
Which of the following fluids exhibit a certain shear stress at zero shear strain rate followed by a straight line relationship between shear stress and shear strain rate?
A
Newtonian fluid
B
Ideal Bingham plastic fluids
C
Pseudo-plastic fluids
D
Dilatent fluids
Question 54Single Answer
What is the specific gravity of a marble stone, which weighs 400N in air, and 200N in water? (g=10m/s2)
A
8
B
6
C
4
D
2
Question 55Single Answer
What is the intensity of pressure in the following SI units, when specific gravity of mercury is 13.6 and the intensity of pressure is 400KPa ?
A
0.3 bar or 4.077m of water or 0.29 mm of Hg
B
4 bar or 5.077m of water or 0.399 mm of Hg
C
0.3 bar or 5.077m of water or 0.599 mm of Hg
D
4 bar or 4.077m of water or 0.299 mm of Hg
Question 56Single Answer
Consider the following statements:
1.If a small upward displacement is given to a floating body, it results in the reduction of the buoyant force acting on the body
2.A slight horizontal displacement does not change either the magnitude or the location of the buoyant force
Which of the above statements is/are correct?
A
Both 1 and 2
B
1 only
C
2 only
D
Neither 1 nor 2
Question 57Single Answer
State whether following flow field is physically possible?
A
Possible for steady, incompressible flow
B
Possible for unsteady, incompressible flow
C
Possible for steady, compressible flow
D
Not Possible
Question 58Single Answer
In a differential manometer, a head of 0.5 m of fluid A in limb 1 is found to balance a head of 0.3 m of fluid B in limb 2. The atmospheric pressure is 760 mm of mercury. The ratio of specific gravities of A to B is
A
0.25
B
0.26
C
2
D
4
Question 59Single Answer
A Reversed Carnot Engine removes 50 kW from a heat sink. The temperature of the heat sink is 250 K and the temperature of the heat reservoir is 300 K. The power required of the engine is
A
10 kW
B
20 kW
C
30 kW
D
50 kW
Question 60Single Answer
On which of the following just in time manufacturing philosophy emphasizes ?
A
man power
B
profit
C
inventory
D
manufacturing
Question 61Single Answer
In a stream line steady flow, two points A and B on a stream line are 1m apart and the flow velocity varies uniformly from 2m/s to 5m/s. What is the acceleration of fluid at B?
A
3 m/s2
B
6 m/s2
C
9 m/s2
D
15 m/s2
Question 62Single Answer
The stream function is given by Ψ = 3xy, then the velocity at the point (2,3) is
A
9
B
-6
C
117
D
10.8
Question 63Single Answer
The boundary layer thickness at a given distance from the leading edge of a flat plate is
A
More for lighter fluid
B
More for denser fluid
C
Less for denser fluid
D
Less for lighter fluid
Question 64Single Answer
In a laminar flow through a circular pipe, the discharge varies
A
Linearly with fluid density
B
Inversely with pressure drop
C
Directly as square of pipe radius
D
Inversely with fluid velocity
Question 65Single Answer
A fluid is flowing over a flat plate. At distance of 8 cm from the leading edge, the Reynolds number is found to be 25600. The thickness of the boundary layer at this point is
A
1.5mm
B
2.5mm
C
4.0mm
D
5.0mm
Question 66Single Answer
Air is flowing over a flat plate with a free stream velocity of 24 m/s, and its kinematic viscosity is 72 ×10-6m2/s. If at a particular point, the Reynolds number is 30000, its location from the leading edge is
A
0.05m
B
0.07m
C
0.08m
D
0.09m
Question 67Single Answer
In a refrigerator, the evaporator and condenser coil temperatures are –33°C and 27°C, respectively. Assuming that the maximum COP is realized, the required power input for a refrigerating effect of 4 kW is
A
8 kW
B
4 kW
C
2 kW
D
1 kW
Question 68Single Answer
In a hydraulic coupling
A
The magnitudes of input and output torques are equal
B
The magnitudes of input torque is greater than output torque
C
The magnitudes of input torque is less than output torque
D
The magnitudes of input torque is negligible as compared to output torque
Question 69Single Answer
Consider the following statements:
1.The wheel can be operated freely in air
2.Pressure at the exit of the nozzle is atmospheric
3.Pressure does not vary along the moving vanes
4.Change the direction of momentum imparts thrust over moving vanes Which of the following statements are applied to impulse turbine?
A
1,2 and 3 only
B
1,2 and 4 only
C
3 and 4 only
D
1,2, 3 and 4
Question 70Single Answer
A water jet 0.0015m2in area issues from a nozzle with 15 m/s velocity. It is made to impinge perpendicular on to a plate that moves away from the jet with a velocity of 5 m/s. The force on the plate due to this impact is
A
150 N
B
1470 N
C
340 N
D
900 N
Question 71Single Answer
Consider the following statements with regard to hydraulic turbines:
1.Kaplan turbines are most efficient at part load operations.
2.If n is the number of jets in a Pelton turbine, then the specific speed is proportional to n2.
3.The flow ratio of Francis turbines are in the range of 0.1 – 0.3.
Which of the above statements is/are correct?
A
1,2 and 3
B
1 and 2 only
C
1 and 3 only
D
2 and 3 only
Question 72Single Answer
Which of the following is a Vector quantity ?
A
Energy
B
Mass
C
Momentum
D
Angle
Question 73Single Answer
Bernoulli’s equation is applicable between any two points located in
A
Rotational flow of an incompressible fluid
B
Irrotational flow of compressible or incompressible fluid
C
Steady, rotational flow of an incompressible fluid
D
Steady, irrotational flow of an incompressible fluid
Question 74Single Answer
Water flows through a smooth circular pipe of diameter D and length L because of a pressure difference ΔP across the length. The volume flow rate is Q and the flow is turbulent with Reynolds number 105. If the pressure difference is increased to 4ΔP the volume flow rate will be
A
2Q
B
A little more than 2Q
C
A little less than 2Q
D
4Q
Question 75Single Answer
Heat is lost from a 100 mm diameter steam pipe placed horizontally in ambient air at 30°C. If the Nusselt number is 25 and the thermal conductivity of the air is 0.03 W/m K, then the heat transfer coefficient will be
A
7.5 W/m2K
B
15 W/m2K
C
25 W/m2K
D
35 W/m2K
Question 76Single Answer
For laminar flow through a round pipe, the shear stress
A
Remains constant over the cross-section
B
Varies linearly with the radial distance
C
Must be zero at all point
D
Varies parabolically with radial distance
Question 77Single Answer
Percentage clongation during tensile test is indicative of
A
Creep
B
Malleability
C
Ductility
D
Elasticity in the metal
Question 78Single Answer
Which of the above statements is not correct in the context of laminar flow through a pipeline?
A
Shear stress is zero at the center and varies linearly with pipe radius
B
Head loss is proportional to square of the average flow velocity
C
The friction factor varies inversely with flow Reynolds number
D
No dispersion of die injected into the flow stream
Question 79Single Answer
Laminar flow between closely spaced parallel plates is governed by the consideration of which one of the following pair of forces?
A
Pressure and inertial forces
B
Gravity and inertial forces
C
Viscous and inertial forces
D
Pressure and inertial forces
Question 80Single Answer
Formation and collapse of vapour bubbles are believed to be the root cause for cavitation in hydraulic turbines. Most favorable condition for the formation of bubbles is set in the turbine at
A
Penstock/nozzl
B
Guide vanes/Inlet of the runner
C
Vanes receiving impact of jet
D
Outlet of the runner/Entrance of the draft tube
Question 81Single Answer
For fully developed laminar flow through a circular pipe with Reynolds number Rethe friction factor is
A
Inversely proportional to Re
B
Proportional to Re
C
Proportional to square of Re
D
Independent of Re
Question 82Single Answer
The ratio of power outlet of the pump to the power input to the pump is known as
A
Mechanical efficiency
B
Static efficiency
C
Overall efficiency
D
Manometric efficiency
Question 83Single Answer
A pump is defined as a device which converts
A
Hydraulic energy into Mechanical energy
B
Mechanical energy into Hydraulic energy
C
Kinetic energy into Mechanical energy
D
None of the above
Question 84Single Answer
The specific speed of a pump is defined as the speed of the unit of such a size that is
A
Delivers the unit discharge at unit head
B
Requires unit power to develop unit head
C
Delivers the unit discharge at unit power
D
Produces unit power with unit head available
Question 85Single Answer
Negative slip occurs in reciprocating pumps, when delivery pipe is
A
Long and suction pipe is short and pump is running atlow speed
B
Long and suction pipe is short and pump is running at high speed
C
Short and suction pipe is long and pump is running at low speed
D
Short and suction pipe is long and pump is running at high speed
Question 86Single Answer
The pressure inside a soap bubble of 50 mm diameter is 25 N/m2 above the atmospheric pressure. The surface tension in soap film would be
A
0.156 N/m
B
0.313 N/m
C
0.624 N/m
D
0.078 N/m
Question 87Single Answer
A Newtonian fluid is one which
A
Is viscous but incompressible
B
Has a linear relationship between the shear stress and the rate of angular deflection
C
Exhibits an increase in viscosity with increasing rate of deformation
D
Exhibits a decrease in viscosity with increasing rate of deformation
Question 88Single Answer
Unlike the viscosity of fluids, the viscosity of gases increases with increasing temperature. This is due to
A
Increased cohesive force between the molecule
B
Increased momentum transfer in the molecules
C
Decreased momentum transfer in the molecules
D
Increase in both cohesive force and momentum transfer
Question 89Single Answer
Manometer is a device used for measuring
A
Velocity at a point in a fluid
B
Pressure at a point in a fluid
C
Discharge of a fluid
D
None of the above
Question 90Single Answer
When a dolphin glides through air, it experiences an external pressure of 0.75 m of mercury. The absolute pressure on dolphin when it is 5m below the free surface of the water is
A
0.10 N/m2
B
0.5 N/m2
C
1.0 N/m2
D
0.15 N/m2
Question 91Single Answer
Which of the above statements is correct?
A
For a floating body, the stable equilibrium condition exists when position of metacenter remains higher than the center of gravity of the body
B
For a floating body, the stable equilibrium condition exists when position of metacenter remains lower than the center of gravity of the body
C
For a floating body, the neutral equilibrium condition exists when position of metacenter remains higher than the center of gravity of the body
D
For a floating body, the unstable equilibrium condition exists when position of metacenter remains higher than the center of gravity of the body
Question 92Single Answer
A wall of 0.6m thickness has normal area of 1.5 m2 and is made up of material of thermal conductivity 0.4 W/mK. If the temperature on the two sides of the wall are 800°C and 1000°C, the thermal resistance of the wall is
A
1.8 K/W
B
1.8 W/K
C
1 K/W
D
1 W/K
Question 93Single Answer
A flownet is a graphical representation of streamlines and euqipotnetial lines such as these lines
A
Intersect each other at various different angles forming irregular shaped nets
B
Intersect each other orthogonally forming curvilinearsquares
C
Indicate the direction but not magnitude of vector
D
Indicate the direction and magnitude of vector
Question 94Single Answer
Which of the above statements is correct for the velocity of potential?
A
Existence of velocity potential is an indication of irrotational nature of the flow
B
The velocity potential automatically satisfies the continuity equation
C
Velocity potential can be defined only for 2-dimensional flow
D
All of the above
Question 95Single Answer
Angle of diverging portion of the venturimeter is limited to 7°, because:
1.Flow decelerates in the diverging portion and pressure increases in the downstream direction. Hence, the fluid experience an adverse pressure gradient, if the divergence angle is large.
2 .Flow separation takes place due to adverse pressure gradient when divergence angle is large.
3 .If the divergence angle is large, a negative pressure is created at the throat which obstructs the flow of fluid.
Which of the above reasons are correct?
A
1, 2 and 3
B
1 and 2 only
C
1 and 3 only
D
2 and 3 only
Question 96Single Answer
A gas is flowing through an insulated nozzle. If the inlet velocity of gas is negligible and there is an enthalpy drop of 45kJ/kg, the velocity of gas leaving the nozzle is
A
100m/s
B
200m/s
C
300m/s
D
350m/s
Question 97Single Answer
Which of the above statements are correct for turbo-prop powered aircrafts?
1 .The propulsion efficiency of turbo-prop is higher than that of turbo-jet and rockets for low speeds up to about 800km/hr.
2.For the same thrust the turbine in the turbo prop aircraft is smaller than in the turbo-jet aircraft.
3.For the turbo-prop the flight velocity cannot exceed the jet velocity.
A
1,2 and 3
B
1 and 2 only
C
2 and 3 only
D
1 and 3 only
Question 98Single Answer
If absolute jet exit velocity from a jet engine is 2800m/s and forward flight velocity is 1400m/s then propulsive efficiency is
A
33.33%
B
40%
C
66.66%
D
90%
Question 99Single Answer
An air-breathing aircraft is flying at an altitude where the air density is half the value at ground level. With reference to the ground level, the air fuel ratio at this altitude will be
A
1
2
B
1
C
2
D
4
Question 100Single Answer
Which of the above statements are correct for rockets?
1.Unlike the turbo-jet aircraft, in rockets the flight velocity can exceed the jet velocity.
2.In rockets gases having lower molecular weight increase the specific thrust.
3.In rockets the gases are expanded in the nozzle up to the atmospheric pressure.
A
1,2 and 3
B
1 and 2 only
C
2 and 3 only
D
1 and 3 only
Chemical
Question 101Single Answer
Average yield of a product in different years is shown in the histogram. If the vertical bars indicate variability during the year, then during which year was the per cent variability over the average of that year the least ?
A
2000
B
2001
C
2002
D
2003
Question 102Single Answer
A rectangle of length d and breadth d/2 is revolved once completely around its length and once around its breadth. The ratio of volumes swept in the two cases is
A
1 : 1
B
1 : 2
C
1 : 3
D
1 : 4
Question 103Single Answer
A long ribbon is wound around a spool up to a radius R. Holding the tip of the ribbon, a boy runs away from the spool with a constant speed maintaining the unwound portion of the ribbon horizontal. In 4 minutes, the radius of the wound portion becomes . In what further time, it will become ?
A
min
B
2 min
C
min
D
4 min
Question 104Single Answer
If n is a positive integer, then
n(n + 1) (n + 2) (n + 3) (n + 4) (n + 5) (n + 6) is divisible by
A
3 but not 7
B
3 and 7
C
7 but not 3
D
neither 3 nor 7
Question 105Single Answer
The area (in m2) of a triangular park of dimensions 50 m, 120 m and 130 m is
A
3000
B
3250
C
5550
D
7800
Question 106Single Answer
Lunch-dinner pattern of a person for m days is given below. He has a choice of a VEG or a NON-VEG meal for his lunch/dinner
(1) If he takes a NON-VEG lunch he will have only VEG for dinner.
(2) He takes NON-VEG dinner for exactly 9 days.
(3) He takes VEG lunch for exactly 15 days.
(4) He takes a total of 14 NON-VEG meals.
What is m?
A
18
B
24
C
20
D
38
Question 107Single Answer
A bank offers a scheme wherein deposits made for 1600 days are doubled in value. The interest being compounded daily. The interest accrued on a deposit of 1000 over the first 400 days would be
A
250
B
183
C
148
D
190
Question 108Single Answer
What is the next number of the following sequence?
2, 3, 4, 7, 6, 11, 8, 15, 10...
A
12
B
13
C
17
D
19
Question 109Single Answer
Two locomotives are running towards each other with speeds of 60 and 40 km/h. An object keeps on flying to and fro from the front tip of one locomotive to the front tip of the other with a speed of 70 km/h. After 30 minutes, the two locomotives collide and the object is crushed. What distance did the object cover before being crushed?
A
50 km
B
45 km
C
35 km
D
10 km
Question 110Single Answer
Weights (in kg) of 13 persons are given below
70, 72, 74, 76, 78, 80, 82, 84, 86, 88, 90, 92, 94.
Two new persons having weights 100 kg and 79 kg join the group. The average weight of the group increases by
A
0 kg
B
1 kg
C
1.6 kg
D
1.8 kg
Question 111Single Answer
A code consists of at most two identical letters followed by at most four identical digits. The code must have at least one letter and one digit. How many distinct codes can be generated using letters A to Z and digits 1 to 9?
A
936
B
1148
C
1872
D
2574
Question 112Single Answer
Two solid iron spheres are heated to 100°C and then allowed to cool. One has the size of a football; the other has the size of a pea. Which sphere will attain the room temperature (constant) first?
A
The bigger sphere
B
The smaller sphere
C
Both spheres will take the same time
D
It will depend on the room temperature
Question 113Single Answer
Find the missing letter
A ? Q E
C M S C
E K U A
G I W Y
A
L
B
Q
C
N
D
O
Question 114Single Answer
The least significant bit of an 8-bit binary number is zero. A binary number whose value is 8 times the previous number has
A
12 bits ending with three zeros
B
11 bits ending with four zeros
C
11 bits ending with three zeros
D
12 bits ending with four zeroes
Question 115Single Answer
A person sells two objects at 1035 each. On the first object he suffers a loss of 10% while on the second he gains 15%. What is his net loss/gain percentage?
A ladder rests against a wall as shown. The top and the bottom ends of the ladder are marked A and B. The base B slips. The central point C of the ladder falls along
A
a parabola
B
the arc of a circle
C
a straight line
D
a hyperbola
Question 118Single Answer
Among isomeric amines, tertiary amines have the lowest boiling points because :
A
they have highest molecular mass
B
they are most basic in nature
C
they are more polar in nature
D
they do not form hydrogen bonds
E
100
Question 119Single Answer
Binomial theorem in algebra gives (1 + x)n = a0 + a1x + a2x2 + ....... + anxn, where a0, a1, ......, an are constants depending on n. What is the sum a0 + a1 + a2 +......+ an?
A
2n
B
n
C
n2
D
n2 + n
Question 120Single Answer
A sphere is made up of very thin concentric shells of increasing radii (leaving no gaps). The mass of an arbitrarily chosen shell is
A
equal to the mass of the preceding shell
B
proportional to its volume
C
proportional to its radius
D
proportional to its surface area
Question 121Single Answer
The correct order of the retention of cations on a sulfonated cation exchange resin column is
A
Ag+ > K+ > Na+ > Li+
B
K+ > Na+ > Ag+ > Li+
C
Li+ > Na+ > K+ > Ag+
D
Li+ > Na+ > Ag+ > K+
Question 122Single Answer
Among F–, Na+, O2– and Mg2+ ions, those having the highest and the lowest ionic radii respectively are
A
O2– and Na+
B
F– and Mg2+
C
O2– and Mg2+
D
Mg2+ and O2–
Question 123Single Answer
In a polarographic measurement, (aqueous KCl solution used as supporting electrolyte) an applied potential more than + 0.4 V, results mainly in the formation of
A
HgI
B
HgII
C
Cl2
D
O2
Question 124Single Answer
The reaction between SbF5 and two equivalents of HF leads to the formation of
A
H2SbF3 + 2F2
B
HSbF2 + 3F2
C
SbF3 + H2 + 2F2
D
[SbF6]– [H2F]+
Question 125Single Answer
The extent of p-electron conjugation in macrocyclic rings of (a) heme, (b) coenzyme B12 and (c) chlorophyll follows the order
A
(a) > (c) > (b)
B
(a) > (b) > (c)
C
(c) > (a) > (b)
D
(b) ≈ (a) > (c)
Question 126Single Answer
The S and L values for 15N atom respectively, are
A
1 and 1
2
B
1 and 0
2
C
1 and 0
D
3 and 0
2
Question 127Single Answer
The product of the reaction of propene, CO and H2 in the presence of CO2(CO)8 as a catalyst is
A
butanoic acid
B
butanal
C
2-butanone
D
methylpropanoate
Question 128Single Answer
The rate of the reaction
Ni(CO)4 + PPh3 [Ni(CO)3(PPh3)] + CO depends on
A
concentration of both the reactants
B
concentration of Ni(CO)4 only
C
concentration of PPh3 only
D
the steric bulk of PPh3
Question 129Single Answer
The hapticities ‘x’ and ‘y’ of the arene moieties in the diamagnetic complex [(x – C6H6)
Ru(y – C6H6)] respectively are
A
6 and 6
B
4 and 4
C
4 and 6
D
6 and 2
Question 130Single Answer
The correct order of the isomeric shift in Mossbauer spectra (57Fe source) of iron compounds is
A
Fe(II) > Fe(III) > Fe(IV)
B
Fe(III) > Fe(II) > Fe(IV)
C
Fe(IV) > Fe(III) > Fe(II)
D
Fe(IV) > Fe(II) > Fe(III)
Question 131Single Answer
The -bond is formed via the overlap of
A
dx2 -y2 and dx2 -y2 orbitals
B
dxz and dxz orbitals
C
dxy and dxy orbitals
D
dyz and dyz orbitals
Question 132Single Answer
Reductive elimination step in hydrogenation of alkenes by Wilkinson catalyst results in (neglecting solvent in coordination sphere of Rh)
A
T-shaped [Rh(PPh3)2Cl]
B
Trigonal-planar [Rh(PPh3)2Cl]2+
C
T-shaped [Rh(H)(PPh3)Cl]+
D
Trigonal-planar [Rh(H)(PPh3)2]
Question 133Single Answer
In the following reaction
[PtCl4]2– + NO2 → AB
compound B is
A
trans-[PtCl2(NO2)(NH3)]–
B
cis[PtCl2(NO2)(NH3)]–
C
trans-[PtCl2(NH3)2]
D
cis-[PtCl2(NO2)2]2–
Question 134Single Answer
Co4(CO)12 adopts the
A
closo—structure
B
nido—structure
C
arachno—structure
D
hypho—structure
Question 135Single Answer
The major product formed in the following reaction is
A
B
C
D
Question 136Single Answer
The compound that is antiaromatic is
A
I
B
II
C
III
D
IV
Question 137Single Answer
The decreasing order of basicity of the following compounds is
A
III > II > III > IV
B
IV > I > II > III
C
III > II > I > IV
D
IV > III > II > 1
Question 138Single Answer
The configurations of carbon atoms C3 and C4 in D-ribose, respectively, are
A
R and S
B
S and R
C
R and R
D
S and S
Question 139Single Answer
The number of histidine amino acid nitrogen atoms coordinated to bimetallic active site of oxyhemocyanin and oxyhemerythrin, respectively, are
A
2, 3 and 3, 3
B
3, 3 and 2, 3
C
3, 3 and 2, 2
D
2, 4 and 3, 2
Question 140Single Answer
In the most stable conformation of neomenthol, stereochemical orientation of the three substituents on the cyclohexane ring are
A
OH : equatorial; i-Pr : equatorial and Me; equatorial
B
OH : axial; i-Pr : equatorial and Me : equatorial
C
OH : equatorial; i-Pr : equatorial and Me ; axial
D
OH ; equatorial; i-Pr : axial and Me : I equatorial
Question 141Single Answer
The reaction of 1-bromo-2-fluorobenzene with furan in the presence of one equivalent of Mg gives
A
B
C
D
Question 142Single Answer
Identify correct statements for mercury as an environment pollutant :
1. Carbanionic biomethylation converts it to MeHg+.
2. Thiol group of cysteine has strong affinity for mercury.
3. Mercury containing industrial catalyst release caused Minamata disaster.
The correct answer is
A
1 and 2
B
1 and 3
C
2 and 3
D
1, 2 and 3
Question 143Single Answer
The increasing order of pKa value of the circled hydrogens in the following compounds is
A
I < II < III
B
I < III < II
C
II < I < III
D
II < III < I
Question 144Single Answer
The absolute configurations of the chiral centres of starting ketone in the following reaction is
A
3R, 6S
B
3S, 6S
C
3R, 6R
D
3S, 6R
Question 145Single Answer
The product for the following sequence of reactions is
A
B
C
D
Question 146Single Answer
A compound with molecular formula C4H6O2 shows band at 1770 cm–1 in IR spectrum and peaks at 178, 68, 28, and 22 ppm in 13C NMR spectrum. The correct structure of the compound is
A
B
C
D
Question 147Single Answer
The cyclic product(s) of the following photochemical reaction is(are)
A
only cis-1, 2-dimethylcyclopentane
B
only trans-1, 2-dimethylcyclopentane
C
a mixture of cis- and trans-1, 2-dimethy-lcyclopentanes
D
only 2, 6-dimethylcyclohexanol
Question 148Single Answer
The major product of the following reaction is
A
B
C
D
Question 149Single Answer
The major product of the following reaction is
A
B
C
D
Question 150Single Answer
For the cell reaction,
Sn(s) + Sn4+ (aq) 2Sn2+(aq),
separate electrode reactions could be written with the respective standard electrode potential data at 25 ºC as
Sn4+ (aq) + 2e → Sn2+ (aq), E0 = +0.15 V
Sn2+ (aq) + 2e → Sn(s), E0 = +0.14 V
When RT/F is given as 25.7 mV, logarithm of the equilibrium constant (In K) is obtained as