📚 Exam by Category
▾
Objective Questions

Latest BHEL Artisan Fitter Exam Question (Objective Questions), MCQ in English

Subjects : Trade Related Question (Fitter), Engineering Calculations, Test of Reasoning

Question Bank BHEL Artisan (Fitter) Exam - English
Back to Exam

Trade Related Question (Fitter)

Question 1Single Answer
What is the primary function of dividers in marking off?
  1. A
    Measuring and transferring distances
  2. B
    Cutting metal
  3. C
    Drilling holes
  4. D
    Filing surfaces
Question 2Single Answer
What material is commonly used for making dividers?
  1. A
    Aluminum
  2. B
    Hardened steel
  3. C
    Plastic
  4. D
    Wood
Question 3Single Answer
How should dividers be maintained to ensure accuracy?
  1. A
    Store in a humid environment
  2. B
    Apply heavy grease
  3. C
    Keep points sharp and clean
  4. D
    Leave in direct sunlight
Question 4Single Answer
What is a scribing block used for?
  1. A
    Marking lines parallel to a surface
  2. B
    Measuring angles
  3. C
    Cutting sheet metal
  4. D
    Drilling holes
Question 5Single Answer
What is the main component of a scribing block?
  1. A
    Blade
  2. B
    Scribe needle
  3. C
    Hammer
  4. D
    Protractor
Question 6Single Answer
What type of dividers are used for precise measurements?
  1. A
    Wing dividers
  2. B
    Spring dividers
  3. C
    Straight dividers
  4. D
    Flat dividers
Question 7Single Answer
How should a scribing block be stored?
  1. A
    In a damp place
  2. B
    Exposed to dust
  3. C
    In a protective case
  4. D
    Submerged in water
Question 8Single Answer
What is the classification of dividers based on their design?
  1. A
    Heavy and light
  2. B
    Single and double
  3. C
    Long and short
  4. D
    Fixed and adjustable
Question 9Single Answer
What care should be taken for dividers to prevent rust?
  1. A
    Use sandpaper
  2. B
    Store in water
  3. C
    Apply oil lightly
  4. D
    Heat regularly
Question 10Single Answer
What is the purpose of a surface plate in marking off?
  1. A
    Providing a flat reference surface
  2. B
    Cutting metal
  3. C
    Measuring angles
  4. D
    Drilling holes
Question 11Single Answer
What is the primary use of a try square?
  1. A
    Checking perpendicularity
  2. B
    Measuring lengths
  3. C
    Drilling holes
  4. D
    Cutting metal
Question 12Single Answer
What material is a try square blade typically made of?
  1. A
    Plastic
  2. B
    Hardened steel
  3. C
    Wood
  4. D
    Aluminum
Question 13Single Answer
How should a try square be maintained?
  1. A
    Store in a humid environment
  2. B
    Bend the blade slightly
  3. C
    Apply heavy grease
  4. D
    Keep blade clean and free of burrs
Question 14Single Answer
What is the function of an ordinary depth gauge?
  1. A
    Measuring angles
  2. B
    Cutting metal
  3. C
    Measuring depth of holes or recesses
  4. D
    Marking lines
Question 15Single Answer
What is the typical accuracy of a protractor?
  1. A
    10 degrees
  2. B
    0.1 degree
  3. C
    5 degrees
  4. D
    1 degree
Question 16Single Answer
How should a protractor be stored to prevent damage?
  1. A
    In a protective cover
  2. B
    In a toolbox with other tools
  3. C
    Exposed to moisture
  4. D
    In direct sunlight
Question 17Single Answer
What is the main use of a protractor in a workshop?
  1. A
    Measuring lengths
  2. B
    Drilling holes
  3. C
    Measuring angles
  4. D
    Filing surfaces
Question 18Single Answer
What is the primary component of an ordinary depth gauge?
  1. A
    Depth bar
  2. B
    Vernier scale
  3. C
    Blade
  4. D
    Protractor
Question 19Single Answer
How should a try square be checked for accuracy?
  1. A
    Compare with a known 90-degree angle
  2. B
    Bend the blade
  3. C
    Submerge in water
  4. D
    Heat the blade
Question 20Single Answer
What is the purpose of a protractor’s scale?
  1. A
    Measuring depth
  2. B
    Measuring angles
  3. C
    Measuring length
  4. D
    Cutting metal
Question 21Single Answer
Which tool is commonly used for marking straight lines on a metal surface?
  1. A
    Divider
  2. B
    Scriber
  3. C
    Caliper
  4. D
    Reamer
Question 22Single Answer
A scriber is generally made of:
  1. A
    Mild steel
  2. B
    Copper
  3. C
    High carbon steel
  4. D
    Aluminium
Question 23Single Answer
The point of a scriber is generally hardened and tempered so that it can:
  1. A
    Resist wear
  2. B
    Bend easily
  3. C
    Increase weight
  4. D
    Reduce length
Question 24Single Answer
Which tool is used for drawing circles and arcs on metal surfaces?
  1. A
    Try square
  2. B
    Protractor
  3. C
    Surface gauge
  4. D
    Divider
Question 25Single Answer
A divider is mainly used for:
  1. A
    Measuring temperature
  2. B
    Marking circles and transferring dimensions
  3. C
    Cutting threads
  4. D
    Grinding surfaces
Question 26Single Answer
The legs of a divider are generally made of:
  1. A
    Copper
  2. B
    Brass
  3. C
    Cast iron
  4. D
    High carbon steel
Question 27Single Answer
Which instrument is used for marking lines parallel to a datum surface?
  1. A
    Scribing block
  2. B
    Micrometer
  3. C
    Screw pitch gauge
  4. D
    Reamer
Question 28Single Answer
A scribing block is normally used on a:
  1. A
    Wooden bench
  2. B
    Surface plate
  3. C
    Welding table only
  4. D
    Grinding wheel
Question 29Single Answer
The base of a scribing block is generally made of:
  1. A
    Plastic
  2. B
    Rubber
  3. C
    Cast iron
  4. D
    Aluminium foil
Question 30Single Answer
The scriber of a scribing block can generally be:
  1. A
    Used only horizontally
  2. B
    Rotated only
  3. C
    Heated continuously
  4. D
    Adjusted vertically
Question 31Single Answer
Which tool is used to check squareness between two surfaces?
  1. A
    Try square
  2. B
    Divider
  3. C
    Outside caliper
  4. D
    Tap wrench
Question 32Single Answer
A try square normally checks an angle of:
  1. A
    30°
  2. B
    45°
  3. C
    90°
  4. D
    60°
Question 33Single Answer
The two main parts of a try square are:
  1. A
    Handle and jaw
  2. B
    Blade and stock
  3. C
    Spindle and sleeve
  4. D
    Flute and shank
Question 34Single Answer
The blade of a try square is generally made of:
  1. A
    Wood
  2. B
    Hardened steel
  3. C
    Copper
  4. D
    Zinc
Question 35Single Answer
A depth gauge is mainly used for measuring:
  1. A
    Diameter of a shaft
  2. B
    Depth of holes and recesses
  3. C
    Angle of a surface
  4. D
    Thread pitch
Question 36Single Answer
Which instrument is commonly used to measure angles directly?
  1. A
    Feeler gauge
  2. B
    Protractor
  3. C
    Plug gauge
  4. D
    Divider
Question 37Single Answer
A simple protractor is generally graduated from:
  1. A
    0° to 180°
  2. B
    0° to 90° only
  3. C
    0° to 45°
  4. D
    0° to 30°
Question 38Single Answer
Which precaution is important while using a try square?
  1. A
    Keep blade and stock clean
  2. B
    Use it as a hammer
  3. C
    Heat it before use
  4. D
    Grind the blade frequently
Question 39Single Answer
A cold chisel is used for cutting metal in the:
  1. A
    Molten state
  2. B
    Vapour state
  3. C
    Liquid state
  4. D
    Cold state
Question 40Single Answer
Cold chisels are generally made of:
  1. A
    High carbon steel
  2. B
    Lead
  3. C
    Copper
  4. D
    Aluminium
Question 41Single Answer
Which part of a cold chisel is struck by a hammer?
  1. A
    Cutting edge
  2. B
    Flank
  3. C
    Point
  4. D
    Head
Question 42Single Answer
The cutting edge angle of a cold chisel for mild steel is approximately:
  1. A
    30°
  2. B
    40°
  3. C
    60°
  4. D
    90°
Question 43Single Answer
Which chisel is used for cutting keyways and narrow grooves?
  1. A
    Flat chisel
  2. B
    Cross-cut chisel
  3. C
    Round nose chisel
  4. D
    Diamond-point chisel
Question 44Single Answer
Which chisel is suitable for making semicircular grooves?
  1. A
    Round-nose chisel
  2. B
    Flat chisel
  3. C
    Cape chisel
  4. D
    Diamond-point chisel
Question 45Single Answer
A diamond-point chisel is commonly used for:
  1. A
    Drilling holes
  2. B
    Cutting sheet metal circles only
  3. C
    Measuring angles
  4. D
    Cutting corners and V-grooves
Question 46Single Answer
Mushrooming on the head of a chisel should be:
  1. A
    Allowed to grow
  2. B
    Removed by grinding
  3. C
    Heated red hot
  4. D
    Covered with grease only
Question 47Single Answer
A power hacksaw is primarily used for:
  1. A
    Measuring metal
  2. B
    Cutting metal stock
  3. C
    Welding metal
  4. D
    Checking threads
Question 48Single Answer
In a power hacksaw, cutting usually takes place during the:
  1. A
    Return stroke only
  2. B
    Forward stroke
  3. C
    Both strokes equally in every machine
  4. D
    Vertical stroke
Question 49Single Answer
A band saw uses a blade in the form of a:
  1. A
    Straight strip with open ends
  2. B
    Circular disc only
  3. C
    Continuous loop
  4. D
    Chain
Question 50Single Answer
A circular saw machine uses a:
  1. A
    Reciprocating blade
  2. B
    Wire blade
  3. C
    Rotating toothed disc
  4. D
    Abrasive belt only
Important Questions Package

BHEL Artisan Fitter Exam Online Question Bank Package

Buy BHEL Artisan Fitter Important Questions, MCQ, question answer in Hindi & English. It will help you to score high marks in BHEL Artisan Fitter question bank 2026 in Online, PDF & Print study material.

+ Free Monthly Current Affairs, GK & more PDF Download
Sr.Package NameAmount
1.BHEL Artisan (Fitter) Exam - Hindi
Description : 1000 Question with Answer
₹101 [₹500]
2.BHEL Artisan (Fitter) Exam - Hindi
Description : 2000 Question with Answer.
₹141 [₹500]
3.BHEL Artisan (Fitter) Exam - Hindi
Description : 3000 Question with Answer
₹171 [₹500]
4.BHEL Artisan (Fitter) Exam - Hindi
Description : 4000 Question with Answer
₹201 [₹500]
5.BHEL Artisan (Fitter) Exam - English
Description : 1000 Question with Answer
₹101 [₹500]
6.BHEL Artisan (Fitter) Exam - English
Description : 2000 Question with Answer
₹141 [₹500]
7.BHEL Artisan (Fitter) Exam - English
Description : 3000 Question with Answer
₹171 [₹500]
8.BHEL Artisan (Fitter) Exam - English
Description : 4000 Question with Answer
₹201 [₹500]
9.BHEL Artisan (Fitter) Exam - Hindi
Description : 1000 Question & Answer Download in PDF (Send by Email)
₹151 [₹450]
10.BHEL Artisan (Fitter) Exam - English
Description : 1000 Question & Answer Download in PDF (Send by Email)
₹151 [₹450]
11.BHEL Artisan (Fitter) Exam Question Bank Book - Hindi
Description : 1000 Question with Answer (Printed Material)
₹450 [₹800]
12.BHEL Artisan (Fitter) Exam Question Bank Book - English
Description : 1000 Question with Answer (Printed Material)
₹390 [₹600]
Back to Exam
Question for BHEL Artisan (Fitter) 2026 - Quiz / Questions / MCQ - Toppersexam