📚 Exam by Category
▾
Objective Questions

Latest AMC Inspector Exam Question (Objective Questions), MCQ in English

Subjects : Core Subject, Gujarati Grammar, English basics, Quantitative aptitude, Logical reasoning, Gujarat & India current affairs

Question Bank AMC Inspector Exam - English
Back to Exam

Core Subject

Question 1Single Answer
A water supply distribution system for an averagely-populated township is to be designed for
  1. A
    Maximum daily demand 
  2. B
    Maximum hourly demand and fire demand 
  3. C
    Average demand 
  4. D
    Maximum daily demand and fire demand or maximum hourly demand, whichever is higher
Question 2Single Answer
 A combined sewerage system is more appropriate for developed areas where
  1. A
    Rainfall occurs for a very few days in a year 
  2. B
    Rainfall occurs almost uniformly throughout the year 
  3. C
    Air temperatures are nearly uniform throughout the year 
  4. D
    Air temperatures through the year include extremes during certain runs of days 
Question 3Single Answer
100 m3 of sludge holds a moisture content of 95%. If its moisture content chagnes to 90%, the volume of this sludge will then be
  1. A
    40.5m3
  2. B
    50m3
  3. C
    75m3
  4. D
    94.7m3
Question 4Single Answer
The design overflow rate of a sedimentation tank is chosen considering
  1. A
    Flow rate through the tank 
  2. B
    Diameter of the particle intended to be removed 
  3. C
    Volume of the sedimentation tank 
  4. D
    Detention time in the tank
Question 5Single Answer
Consider the following statements in respect of flow equalization in a waste water treatment plant : 
1. Biological treatment is enhanced because shock loadings are eliminated or minimized
2. Flow equalizations is an attractive option for upgrading the performance of overloaded treatment plants.
3. Inhibiting substances can be diluted and pH can be stabilized
4. Thickening performance of primary sedimentation tanks following grit removal is improved.
 Which of the above statements are correct? 
  1. A
    1, 2, 3 and 4 
  2. B
    1, 2 and 3 only 
  3. C
    1, 2 and 4 only 
  4. D
    3 and 4 only   
Question 6Single Answer
Consider the following statements :
1. There will be no defects in select grade timbers.
2. The codal values for strength of grade-II timer without defects may be reduced by 37.5%.
3. For timber used as columns, the permissible stress in ungraded timbers is adopted with a multiplying factor of 0.50.
4. In case of wind force and earthquakes, a modification factor of 1.33 is adopted. Which of the above statements are correct ? 
  1. A
    1 and 3 only
  2. B
    1 and 4 only
  3. C
    2 and 4 only
  4. D
    2 and 3 only
Question 7Single Answer
Consider the following statements regarding timber :
1. The strength of timber increases by Kiln seasoning.
 2. Cutting of wood is to be done prior to treatment.
3. Water seasoning is good for prevention of warping.
4. ASCU treatment enhances the strength of wood. Which of the above statements are correct ?
  1. A
    1, 2 and 3 only
  2. B
    2, 3 and 4 only
  3. C
    1, 3 and 4 only
  4. D
    1, 2, 3 and 4
Question 8Single Answer
Gase(s) emitted during rotting or decomposition of timber is /are mainly
  1. A
    Methane and Hydrogen
  2. B
    Hydrogen Sulphide
  3. C
    Carbonic acid and Hydrogen
  4. D
    Ammonia
Question 9Single Answer
Efflorescence of bricks is due to
  1. A
    Excessive burning of bricks
  2. B
    High silt content in brick clay
  3. C
    High porosity of bricks
  4. D
    Soluble salts present in parent clay
Question 10Single Answer
Disintegration of bricks masonry walls is primarily due to
1. Efflorescence
2. Magnesium sulphate in brick  
3. Calcined clay admixtures
4. Kankar nodules
Which of the a above statements are correct ? 
  1. A
    1, 2 and 3 only
  2. B
    1, 2 and 4 only
  3. C
    3 and 4 only
  4. D
    1, 2, 3 and 4
Question 11Single Answer
Consider the following statements:
1. IS 3583 refers to Burnt Clay Paving Bricks.
2. IS 5779 refers to Burnt Clay Soling Bricks.
3. IS 3952 refers to Burnt Clay Hollow Bricks.
4. IS 2222 refers to Burnt Clay Lay Bricks.
Which of the above statements are correct?
  1. A
    1, 2 and 3 only
  2. B
    1, 2 and 4 only
  3. C
    3 and 4 only
  4. D
    1, 2, 3 and 4
Question 12Single Answer
Consider the following statements:
1. A high aggregate impact value indicates strong aggregates.
2. A low aggregate crushing value indicates high crushing strength of aggregates.
3. Aggregates having elongation index values greater than 15% are generally considered suitable for pavement construction.
4. Flakiness index of aggregates should not be less than 25% for use in road construction.
Which of the above statements are correct?
  1. A
    2 and 3 only
  2. B
    2 and 4 only
  3. C
    1 and 3 only
  4. D
    1 and 4 only
Question 13Single Answer
Consider the following statements regarding refractory bricks in furnaces:
1. The furnace is fired at temperatures more than 1700°C.
2. Silica content in the soil should be less than 40%.
3. Water absorption of bricks should not exceed 10%
4. Chrome bricks are known as basic bricks. Which of the above statements are correct?
  1. A
    1 and 2 only
  2. B
    2 and 4 only
  3. C
    1 and 3 only
  4. D
    3 and 4 only
Question 14Single Answer
Consider the following statements about lime:
1. Calcination of limestone results in quick lime.
2. Lime produced from pure variety of chalk is hydraulic lime.
3. Hydrated lime is obtained by treating quick lime with water.
Which of the above statements are correct?
  1. A
    1, 2 and 3
  2. B
    1 and 2 only
  3. C
    2 and 3 only
  4. D
    1 and 3 only
Question 15Single Answer
Consider the following statements:
1. If more water is added to concrete for increasing its workability, it results into concrete of low strength.
2. No slump is an indication of a good workable concrete.
3. Higher the slump of concrete, lower will be its workability.
4. Workability of concrete is affected by water content as well as water-cement ratio.
Which of the above statements are correct?
  1. A
    1 and 3 only
  2. B
    2 and 3 only
  3. C
    1 and 4 only
  4. D
    2 and 4 only
Question 16Single Answer
One bag of Portland cement, 50 kg in weight, would normally have a bulk volume of
  1. A
    30 l 
  2. B
    35 l
  3. C
    40 l
  4. D
    45 l
Question 17Single Answer
AsCu, a preservative for wood, developed by the Forest Research Institute, Dehradun, comprises of chemicals:
  1. A
    1 : 1 : 1
  2. B
    1 : 2 : 3
  3. C
    1 : 2 : 4
  4. D
    1 : 3 : 4
Question 18Single Answer
Consider the following statements related to autoclave bricks:
1.Less water absorption compared to other bricks.
2.Noise reduction
3.It is cheap compared to other types of bricks.
4.Requirement of bulk volume of mortar in joints being relatively less compared to other types of brick masonry.
5.Not recommended for outer walls. 
Which of the above statements are relevant to the use of ‘autoclave’ bricks? 
  1. A
    1, 2 and 4
  2. B
    1, 3 and 5
  3. C
    2, 3 and 4
  4. D
    2, 4 and 5
Question 19Single Answer
The minimum number of annular rings to be seen in every 2.54 cm in the radial direction from the core for timber to be classified as ‘Dense’ is
  1. A
    10
  2. B
    20
  3. C
    25
  4. D
    30
Question 20Single Answer
If the actual thickness of a brick masonry wall is 19 cm, its effective length is 2.70 m, its effective height is 2.82 m and its code specified stiffening coefficient is 1.2 then, for design considerations, the slenderness ratio of the wall will be taken as
  1. A
    11.8
  2. B
    12.4
  3. C
    14.2 
  4. D
    14.8
Question 21Single Answer
What will be the depth of penetration of the plunger in Vicat Apparatus (IS : 5513 - 1976) from the bottom of the Vicat Mould, when the cement paste is tested for standard consistency, according to IS 4031 – 1988 ?
  1. A
    11 to 15 mm
  2. B
    8 to 10 mm
  3. C
    15 to 17 mm
  4. D
    5 to 7 mm
Question 22Single Answer
Two sewer pipelines A and B (having the same diameter and made of the same material) are laid at a bed slope of 1 in 225 and 1 in 625, respectively. Determine the ratio of their carrying capacities (QA to QB) .
  1. A
  2. B
  3. C
    1
  4. D
Question 23Single Answer
Select the correct statement with respect to an over - reinforced cement concrete section under the working stress method .
  1. A
    The compressive stress in steel reaches the allowable limit before the maximum tensile stress in concrete reaches the allowable limit
  2. B
    Tensile steel stress and maximum compressive stress in concrete simultaneously reach their allowable limits
  3. C
    The allowable limiting stress is reached in concrete before the steel stress reaches the limiting value
  4. D
    The tensile stress in steel reaches the allowable limit before the maximum compressive stress in concrete reaches the allowable limit
Question 24Single Answer
A cantilever beam of span L is built - in at the support. It is restrained against lateral deflection and torsion at the free end. The effective length of compression flange for the beam as per IS 800 : 2007 is
  1. A
    0.5 L
  2. B
    0.85 L
  3. C
    2 L
  4. D
    0.75 L
Question 25Single Answer
What is the principle of plane surveying ?
  1. A
    Working from part to whole
  2. B
    Working from point to area
  3. C
    Working from angle to volume
  4. D
    Working from whole to part
Question 26Single Answer
According is IS 5968 : 1987, the minimum radius of radius of curve to be provided in the alignment of unlined canals carrying a discharge of less than 30 cumecs up to 15 cumecs is :
  1. A
    100 m
  2. B
    1000 m
  3. C
    600 m
  4. D
    150 m
Question 27Single Answer
A Pelton wheel is to be designed for a pitch diameter of 1 m and jet diameter of 0.1 m. The number of buckets on the runner computed by Taygun’s formula is :
  1. A
    20
  2. B
    25
  3. C
    15
  4. D
    10
Question 28Single Answer
What is the effect of fly ash in concrete ?
  1. A
    Reduces the secondary hydration process
  2. B
    Increases the heat of hydration
  3. C
    Increases the amount of air entrainment
  4. D
    Reduces the heat of hydration
Question 29Single Answer
As per IS 456 : 2000, the minimum grade of concrete to be used for plain concrete and reinforced concrete, respectively, in concrete works exposed directly along the sea coast are :
  1. A
    M 20 and M 30
  2. B
    M 20 and M 25
  3. C
    M 22 and M 40
  4. D
    M 15 and M 25
Question 30Single Answer
Identify the property that changes as a function of the geometrical dimensions of a section in structural materials :
  1. A
    Mass density
  2. B
    Moment of inertia
  3. C
    Poission’s ratio
  4. D
    Modulus of elasticity
Question 31Single Answer
What is the main purpose of Environmental Impact Assessment (EIA)?
  1. A
    To assess the environmental pollution levels
  2. B
    To assess the sustainability of a project
  3. C
    To evaluate the potential environmental impacts of a proposed project
  4. D
    To measure the economic benefits of a project
Question 32Single Answer
Which of the following is a major method for assessing the environmental impact of projects?
  1. A
    Environmental Cost-Benefit Analysis
  2. B
    SWOT Analysis
  3. C
    Impact Matrix Method
  4. D
    Delphi Method
Question 33Single Answer
The methodology of EIA typically includes which of the following steps?
  1. A
    Project screening and scoping
  2. B
    Identification of stakeholders
  3. C
    Formulation of legal framework
  4. D
    Both a and b
Question 34Single Answer
Which type of assessment focuses on identifying potential impacts of a project before it is implemented?
  1. A
    Pre-Project Environmental Impact Assessment
  2. B
    Post-Project Environmental Impact Assessment
  3. C
    Environmental Auditing
  4. D
    Cumulative Impact Assessment
Question 35Single Answer
Which is the first stage of the Environmental Impact Assessment process?
  1. A
    Impact prediction
  2. B
    Scoping
  3. C
    Impact assessment
  4. D
    Mitigation
Question 36Single Answer
The main source of carbon monoxide pollution in urban areas is:
  1. A
    Industrial emissions
  2. B
    Vehicular emissions
  3. C
    Forest fires
  4. D
    Agricultural activities
Question 37Single Answer
Which gas is the main contributor to acid rain?
  1. A
    Nitrogen gas
  2. B
    Sulfur dioxide
  3. C
    Methane
  4. D
    Carbon monoxide
Question 38Single Answer
Photochemical smog is mainly caused by:
  1. A
    Carbon monoxide
  2. B
    Sulfur dioxide
  3. C
    Hydrocarbons and nitrogen oxides
  4. D
    Lead compounds
Question 39Single Answer
Which air pollutant is responsible for ozone layer depletion?
  1. A
    Carbon dioxide
  2. B
    Methane
  3. C
    Chlorofluorocarbons (CFCs)
  4. D
    Nitrogen dioxide
Question 40Single Answer
The major source of particulate matter (PM10 and PM2.5) in the air is:
  1. A
    Power plants
  2. B
    Diesel engines
  3. C
    Wildfires
  4. D
    All of the above
Question 41Single Answer
Which parameter is most critical for determining pavement thickness in flexible pavement design as per IRC:37?
  1. A
    Subgrade CBR
  2. B
    Pavement width
  3. C
    Surface roughness
  4. D
    Traffic speed
Question 42Single Answer
In pavement design, the term “design traffic” refers to?
  1. A
    Number of standard axle repetitions over design life
  2. B
    Annual average daily traffic
  3. C
    Peak hour traffic
  4. D
    Maximum axle load in a day
Question 43Single Answer
The standard axle load used in India for pavement design is?
  1. A
    70 kN
  2. B
    120 kN
  3. C
    100 kN
  4. D
    80 kN
Question 44Single Answer
Elastic modulus of bituminous layer primarily depends on?
  1. A
    Subgrade moisture
  2. B
    Bitumen grade and temperature
  3. C
    Air temperature
  4. D
    Shoulder width
Question 45Single Answer
The “structural number” concept is used in which pavement design method?
  1. A
    Westergaard’s method
  2. B
    McLeod method
  3. C
    CBR method
  4. D
    AASHTO method
Question 46Single Answer
Rigid pavement design mainly resists loads through?
  1. A
    Individual layer strength
  2. B
    Beam action and slab rigidity
  3. C
    Load spreading through granular layers
  4. D
    Surface friction
Question 47Single Answer
The fatigue cracking in flexible pavements is caused mainly due to?
  1. A
    Heavy rainfall
  2. B
    Low temperature
  3. C
    Oxidation of bitumen
  4. D
    Repeated traffic load applications
Question 48Single Answer
The primary factor influencing dowel bar diameter in rigid pavement?
  1. A
    Slab width
  2. B
    Joint spacing
  3. C
    Surface texture
  4. D
    Wheel load
Question 49Single Answer
“Radius of relative stiffness” in a concrete pavement depends on?
  1. A
    Concrete grade only
  2. B
    Slab thickness only
  3. C
    Modulus of subgrade reaction and slab stiffness
  4. D
    Pavement joint type
Question 50Single Answer
Which bitumen grade is more suitable for high-temperature zones?
  1. A
    VG-40
  2. B
    VG-20
  3. C
    VG-30
  4. D
    VG-10
Important Questions Package

AMC Inspector Exam Online Question Bank Package

Buy AMC Inspector Important Questions, MCQ, question answer in Hindi & English. It will help you to score high marks in AMC Inspector question bank 2026 in Online, PDF & Print study material.

+ Free Monthly Current Affairs, GK & more PDF Download
Sr.Package NameAmount
1.AMC Inspector Exam - English
Description : 1000 Question with Answer.
₹101 [₹50]
2.AMC Inspector Exam - English
Description : 2000 Question with Answer.
₹151 [₹500]
3.AMC Inspector Exam - English
Description : 3000 Question with Answer.
₹181 [₹500]
4.AMC Inspector Exam - English
Description : 4000 Question with Answer.
₹201 [₹500]
5.AMC Inspector Exam - English
Description : 1000 Question & Answer Download in PDF (Send by Email)
₹151 [₹450]
6.AMC Inspector Exam Question Bank Book - English
Description : 1000 Question with Answer (Printed Material)
₹390 [₹600]
Back to Exam
Question for Ahmedabad Municipal Inspector 2026 - Quiz / Questions / MCQ - Toppersexam